-
GD Commerce EDA-M300 - page 1
GD Systems Page - 1 Windmill Hardware Specification In order to run Windmill or PanCom software the following system req uirements must be satisfied: 1.1 PC Requirements Pentium Processor running Windows 95 or late r The display must be run in a resolutions mode of 80 0 x 600 or greater. Serial port Com1, Com2 or Com3 As som ...
-
GD Commerce EDA-M300 - page 2
GD Systems Page - 2 Windmill 3.2 Installing Program files 3.2.1 Installing Windmill from CD · Before starting any installation ensure any oth er applications have terminated to avoid so ftware conflicts. · Insert the CD in the CD player. · Using Windows Explorer or My Computer select the CD dr ive. - usually D: · Double ...
-
GD Commerce EDA-M300 - page 3
GD Systems Page - 3 Windmill You will be prompted to change the disk at various stages but apart from this the procedure is ve ry similar to that detailed in section 3.2.1. 3.2.4 Installing PanCom software from 3.5" disks This is again very similar to the above installation of Windmill from 3.5" disks. Instead of copying ...
-
GD Commerce EDA-M300 - page 4
GD Systems Page - 4 Windmill 5.0 Using Windmill Software 5.1 Defining a new system. In order to create a new system click on the ‘crea te new’ button. The screen will display blank pa nel and device information as shown i n figure 5.2. To change t he settings go to section 5. 4 5.2 Loading from an earlier system stored on a d ...
-
GD Commerce EDA-M300 - page 5
GD Systems Page - 5 Windmill Device Type The device type of the unit installed . To ensure correct operation this value must be correct. The codes follow the product code. If you are unsure then the ‘X’ option must be used. Zone The zone number must be programmed betwee n the following values EDA-M100 system 1 – 999 zones ED ...
-
GD Commerce EDA-M300 - page 6
GD Systems Page - 6 Windmill Location text The location text cannot be changed on this scr een and is displayed for refer ence only. Zone number The zone number cannot be changed on this screen and is d isplayed fore reference only. Initial Delay: Setting the initial delay will cause the system to display an a larm condition immediately ...
-
GD Commerce EDA-M300 - page 7
GD Systems Page - 7 Windmill Radio Sounders Tone The tone for the rad io sounder can be set. The default tone is ton e 4 (swept Tone). If EDA-A910 hard wired soun ders are being used to matc h the tone of the radio units then the tone for the hardwired sounders is set inside the ind ividual units. Radio Sounder Auxiliary If the radio so ...
-
GD Commerce EDA-M300 - page 8
GD Systems Page - 8 Windmill Alert When Alert is pressed on the corresponding panel the sounder circuits, auxiliary relays and radio sounders operate as progra mmed. For a more detailed description of the sounder c ircuits, auxiliary relays and radio sounders see the device progr amming section (5.4.1) R elay operation silence alarm Whe ...
-
GD Commerce EDA-M300 - page 9
GD Systems Page - 9 Windmill Display Low Batteries NOT IMPLEMENTED Timeout Values The system has many settings or ope rations, which after a predetermined period o f time automatically cancel. This is where these value s are set. Refer to the EDA-M100 manual for descriptions of these values Analogue Global Options Only required fo ...
-
GD Commerce EDA-M300 - page 10
GD Systems Page - 10 Windmill When downloading settings to the EDA-M200 pa nel, the options and messages must be pe rformed sepa- rately. Select messages first and download the m to the panel. Then select options and downlo ad them to the panel. 5.9 Print System Settings to Disk In order to print the settings , the system allows t ...
-
GD Commerce EDA-M300 - page 11
GD Systems Page - 11 Windmill Since we want to download from a panel click 'Dow nload from Panels' 6.1.1 Site Information Screen Clicking 'Download from Panels' you will be pres ented with the screen shown Below: Our site name is 'College' so this is entered in the site na me field. In the next field we ...
-
GD Commerce EDA-M300 - page 12
GD Systems Page - 12 Windmill Simply select the location and click Save. Once you are happy with the save loc ation click next >>. 6.1.3 File Control and Panel Download Screens Following on from the previous screen you are presented wit h the screen shown Below: From this screen you can add new panels to the system, go to t ...
-
GD Commerce EDA-M300 - page 13
GD Systems Page - 13 Windmill Providing the details shown are correc t connect the PC to the module port of the panel, click con tinue with the mouse and press the dump button insid e the panel Twice. After a few seconds the panel will start communicating with the PC an d a progress bar will appear where the continue button was previ ...
-
GD Commerce EDA-M300 - page 14
GD Systems Page - 14 Windmill Data analysis is made up of three main stages: i) Processing of Downloaded Data, ii) Correction of corrupted lines (if any), iii) Report Generation. At this stage files can be added or removed us ing the corresponding buttons. Clicking on Process Files proceeds with the analysis. 6.1.4i File Pro ...
-
GD Commerce EDA-M300 - page 15
GD Systems Page - 15 Windmill If the corrected line did not pas s the validity checks or was altered by the user in suc h a way that it no longer passed its validity checks then the Use >> button would be de-activated un til the line passed these checks. For more information on corrupt files see Appendix A. Once the processi ...
-
GD Commerce EDA-M300 - page 16
GD Systems Page - 16 Windmill If this highest strength is below the standard 37 then two warning stars are displayed after the strength. The highest strength is also flagged if it is stored as 0, this time using a '-?', to ind icate that it may be a panel anomaly. The highest panel strength is again in cluded along with the ...
-
GD Commerce EDA-M300 - page 17
GD Systems Page - 17 Windmill Our example uses townhall files 1, 2 and 3. As stated thes e are selected by holding the control key and selecting each file. Upon clicking Open yo u will be returned back to the control screen where the selected files will be displayed in the downloaded files list. If required, files can b e removed by ...
-
GD Commerce EDA-M300 - page 18
GD Systems Page - 18 Windmill Example M200 Download ...
¿Tienes una pregunta acerca de GD Commerce EDA-M300?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con GD Commerce EDA-M300, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con GD Commerce EDA-M300 probablemente compartirá una forma de solucionarlo.