-
Cisco Systems 3750 - page 1
Table of Contents Configuring Inter−VLAN Routing with Catalyst 3750 Series Switches in a Stacked Configuration .........1 Document ID: 45002 ................................................................................................................................1 Introduction ................................................................ ...
-
Cisco Systems 3750 - page 2
Configuring Inter−VLAN Routing with Catalyst 3750 Series Switches in a Stacked Configuration Document ID: 45002 Introduction Before You Begin Conventions Prerequisites Components Used Background Theory IP Routing on a Stack of 3750s Related Products Configure Network Diagram Practical Tips Configurations Verify Troubleshoot Troubleshooting Proced ...
-
Cisco Systems 3750 - page 3
Components Used The information in this document is based on the software and hardware versions below. Two Catalyst 3750G−24T switches running 12.1(14)EA1 EMI Software Release stacked together • Catalyst 2950G−48 running 12.1(12c)EA1 EI Software Release • Catalyst 2948G running 6.3(10) Software Release • Note: The configuration from the C ...
-
Cisco Systems 3750 - page 4
Generating and distribution of the Distributed Cisco Express Forwarding (dCEF) database to the different stack members • The MAC address of the master is used as source MAC of routed packets • Packets that need process switching are handled by CPU of the master • The stack members perform the following tasks: They act as routing standby switc ...
-
Cisco Systems 3750 - page 5
The above diagram shows a small sample network with the stack of Catalyst 3750s providing inter−VLAN routing between the various segments. The following are the three user defined VLANs: VLAN 2 − user VLAN • VLAN 3 − server VLAN • VLAN 10 − management VLAN • The default gateway configured on each server and host device should be the c ...
-
Cisco Systems 3750 - page 6
VLAN 1 is not used for management. All ports in Catalyst switches default to VLAN 1, and any devices connected to non−configured ports will be in VLAN 1. This may cause potential issues for the management of switches, as explained above. • A Layer 3 (L3) (routed) port is used to connect to the default gateway port. In this diagram, a Cisco 7200 ...
-
Cisco Systems 3750 - page 7
description To 2950 switchport trunk encapsulation dot1q ! !−−− Dot1q trunking (with negotiation) is configured on the L2 switch. !−−− If DTP is not supported on the far switch, issue the !−−− switchport mode trunk command !−−− to force the switch port to trunk mode. !−−− Note: The default trunking mode is dynamic auto ...
-
Cisco Systems 3750 - page 8
interface GigabitEthernet1/0/22 ! interface GigabitEthernet1/0/23 ! interface GigabitEthernet1/0/24 ! interface GigabitEthernet2/0/1 description To 2948G switchport trunk encapsulation dot1q ! !−−− Output suppressed. ! interface GigabitEthernet2/0/23 ! interface GigabitEthernet2/0/24 ! interface Vlan1 no ip address shutdown ! interface Vlan2 ...
-
Cisco Systems 3750 - page 9
Note: Since the 3750 is configured as a VLAN Trunk Protocol (VTP) server, the VTP configuration is not displayed by the switch. This is standard behavior. The commands below are used on this switch to create a VTP server with the three user−defined VLANs from global configuration mode. C3750G−24T(config)# vtp domain cisco C3750G−24T(config)# ...
-
Cisco Systems 3750 - page 10
switchport mode access no ip address spanning−tree portfast ! !−−− Output suppressed. interface GigabitEthernet0/1 switchport trunk encapsulation dot1q no ip address ! interface GigabitEthernet0/2 no ip address ! interface Vlan1 no ip address no ip route−cache shutdown ! interface Vlan10 description MANAGEMENT !−−− IP address used t ...
-
Cisco Systems 3750 - page 11
begin ! # ***** NON−DEFAULT CONFIGURATION ***** ! ! #time: Fri Jun 30 1995, 05:04:47 ! #version 6.3(10) ! ! #system web interface version(s) ! #test ! #system set system name Cat2948G ! #frame distribution method set port channel all distribution mac both ! #vtp !−−− VTP domain is configured to be that same as the 3550 (VTP server). set vtp ...
-
Cisco Systems 3750 - page 12
Verify This section provides information you can use to confirm your configuration is working properly. Certain show commands are supported by the Output Interpreter Tool ( registered customers only ) , which allows you to view an analysis of show command output. Catalyst 3750 show switch − The show switch command tells what the stack consists of ...
-
Cisco Systems 3750 - page 13
E1 − OSPF external type 1, E2 − OSPF external type 2, E − EGP i − IS−IS, L1 − IS−IS level−1, L2 − IS−IS level−2, ia − IS−IS inter area * − candidate default, U − per−user static route, o − ODR P − periodic downloaded static route Gateway of last resort is 200.1.1.2 to network 0.0.0.0 200.1.1.0/30 is subnetted, 1 ...
-
Cisco Systems 3750 - page 14
200.1.1.1 disabled disabled 2−1000 show trunk Cat2948G> (enable) show trunk * − indicates vtp domain mismatch Port Mode Encapsulation Status Native vlan −−−−−−−− −−−−−−−−−−− −−−−−−−−−−−−− −−−−−−−−−−−− −−−−−−−−−−− 2/49 desirable dot1q ...
-
Cisco Systems 3750 - page 15
Updated: Mar 10, 2005 Document ID: 45002 Cisco − Configuring Inter−VLAN Routing with Catalyst 3750 Series Switches in a Stacked Configuration ...
¿Tienes una pregunta acerca de Cisco Systems 3750?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cisco Systems 3750, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cisco Systems 3750 probablemente compartirá una forma de solucionarlo.