-
Zenoah G6200 - page 1
G6200 G B GB-1 G6200 OWNER’S MANUAL CHAIN SA W G B 848C9F93A0 (807) ...
-
Zenoah G6200 - page 2
G6200 GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Read operator's instruction book before operating this machine. W ear head, e ye and ear protection. Use the chain saw with two hands. Wa r ning! Danger of kickback. Read, understand and follow all warnings. APPRO V AL NUMBER OF CE EXHA UST EMISSION REGULA TION (2002/88/EC) e13 * 97/68SH3 ...
-
Zenoah G6200 - page 3
G6200 G B GB-3 Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 6 3. Installing Guide Bar and Saw Chain ......................................... 7 4. Fuel and Chain Oil .................................................... ...
-
Zenoah G6200 - page 4
G6200 GB-4 10. Keep all parts of your body away from the saw chain when the engine is run- ning. 11. Before you start the engine, make sure the saw chain is not contacting anything. 12. Always carry the chain saw with the engine stopped, the guide bar and saw chain to the rear , and the muffler away from your body . 13. Always inspect the chain saw ...
-
Zenoah G6200 - page 5
G6200 G B GB-5 (3) Make certain that the area in which you are cutting is fr ee from obstruc- tions. Do not let the nose of the guide bar contact a log, branch, or any other obstruction which could be hit while you are operating the saw . (4) Cut at high engine speeds. (5) Do not overreach or cut above shoul- der height. (6) Follow the manufacturer ...
-
Zenoah G6200 - page 6
G6200 GB-6 2. Explanation of Symbols on the Machine W ARNING • For safe operation and maintenance, symbols are car ved in relief on the machine. According to these indications, please be careful not to make any mistake. The screw under the “H” stamp is The High-speed adjustment scr ew . The port to refuel “MIX GASOLINE” Position: Fuel cap ...
-
Zenoah G6200 - page 7
G6200 G B GB-7 5. Fit the chain cover to the power unit and fasten the nuts to finger tightness. 6. While holding up the tip of the bar , adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail. 7. Tighten the nuts securely with the bar tip held up (12 ~ 15 N·m). Then check the chain ...
-
Zenoah G6200 - page 8
G6200 GB-8 4. Fuel and Chain Oil ■ FUEL W ARNING • Gasoline is very flammable. A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool bef ore refuel- ing the unit. Select outdoor bare ground f or fuel- ing and move at least 3 m (10 ft) a way fr om the fueling point before starting the engine. 4. ...
-
Zenoah G6200 - page 9
G6200 G B GB-9 7. Allow the engine to warm up with the throttle lever pulled slightly . W ARNING •K eep clear of the sa w chain as it will start rotating upon starting of engine . ■ CHECKING THE OIL SUPPL Y W ARNING • Make sure to set up the bar and the chain when c hec king the oil supply . If not, the rotating parts may be e xposed. It is v ...
-
Zenoah G6200 - page 10
G6200 GB-10 ■ ICING PREVENTION SYSTEM This system prevents icing of the carbur etor which some- times happen while sawing in winter . When your saw has stopped or slowed down abruptly , use the system as follows: 1. Remove the air cleaner cover , air filter , and silencer . 2. Unhook the hatch on the rear wall of the cylinder cover and turn it up ...
-
Zenoah G6200 - page 11
G6200 G B GB-11 6. Sawing • Before pr oceeding to your job, read the section “For Safe Op- eration”. It is recommended to first practice sa wing easy logs. This also helps you get accus- tomed to your unit. •A lwa ys follo w the safety regu- lations. The chain saw m ust only be used f or cutting wood. It is forbid den to cut other types of ...
-
Zenoah G6200 - page 12
G6200 GB-12 A log lying on the gr ound Saw down halfway , then roll the log over and cut from the opposite side. A log hanging off the ground In area A, saw up fr om the bottom one-third and finish by sawing down from the top. In ar ea B, saw down from the top one-third and finish by sawing up fr om the bot- tom. Cutting the limbs of Fallen T ree 2 ...
-
Zenoah G6200 - page 13
G6200 G B GB-13 ■ PERIODICAL SER VICE POINTS 1. Cylinder fins Dust clogging between the cylinder fins will cause overheat- ing of the engine. Periodically check and clean the cylinder fins after removing the air cleaner and the cylinder cover . When installing the cylinder cover , make sure that switch wires and grommets ar e positioned correctly ...
-
Zenoah G6200 - page 14
G6200 GB-14 W ARNING • This saw is equipped with one of the f ollowing low kickbac k bar/chain combinations: Zenoah Part Number Bar Size Guide Bar Saw Chain 16 3670-52112 848CC3LG60 (73LGX) 18 3673-52113 848CC3LG66 (73LGX) 20 3674-52113 848CC3LG72 (73LGX) W ARNING • Be sure to round off the fr ont edge to reduce the c hance of kic kback or tie- ...
-
Zenoah G6200 - page 15
G6200 G B GB-15 9. T r oubleshooting Guide Case 1. Starting failure W ARNING • Make sure the icing prevention system is not w orking. 11. Specifications Power unit: Displacement (cm 3 ): ............................................. 62.0 Fuel: ................ Mixture (Gasoline 50 : T wo-cycle oil 1) (when using ZENOAH genuine oil) Fuel tank capa ...
-
Zenoah G6200 - page 16
G6200 GB-16 Limited warranty Should any failure occur on the pr oduct under normal operating conditions within the applicable warranty pe- riod, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer . W ARRANTY PERIOD: 1 year (6 months if used profes- sionally , and 30 days if used for rental purpose) from the d ...
¿Tienes una pregunta acerca de Zenoah G6200?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Zenoah G6200, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Zenoah G6200 probablemente compartirá una forma de solucionarlo.