-
Husqvarna 322L - page 1
322C 322L 325L 325L X-SERIES Operator's manual (EP A) Read through the Operator‘s Manual carefully and understand the content before using the machine. 101 91 71-95 325L XT-SERIES 325C 325C X-SERIES ...
-
Husqvarna 322L - page 2
2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine. Always use • A protective helmet where ther ...
-
Husqvarna 322L - page 3
English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal pr otective equipment ............................................. 4 The ...
-
Husqvarna 322L - page 4
4 – English The machine ‘ s saf ety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “What is what“ to locate where this equipment is positioned on your machine.) P ersonal pr otective equipment SAFETY INS ...
-
Husqvarna 322L - page 5
English – 5 SAFETY INSTR UCTIONS 4. Vibration damping system Y our machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. U se of incorrectly wound cord or incorr ect cutting equipment increases the level of vibration. The machine ’ s vibration damping system reduces the ...
-
Husqvarna 322L - page 6
6 – English 3. Cutting attachment guard • Ensure that the spray guard is undamaged and is not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" . SAFETY INSTR UCTIONS Contr ol, maintenance and service of the machine ‘ ...
-
Husqvarna 322L - page 7
English – 7 SAFETY INSTR UCTIONS 6. Cutting equipment The section describes how through corr ect maintenance and through using the right type of cutting equipment you can: • Obtain maximum clearing capacity. • Increase the service life of the cutting equipment. T wo basic rules: 1) Only use the cutting and guard equipment we recommend! See ch ...
-
Husqvarna 322L - page 8
8 – English SAFETY INSTR UCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like. • When storing and tra ...
-
Husqvarna 322L - page 9
English – 9 ! General w orking instructions SAFETY INSTR UCTIONS Basic working techniques • Always drop to idling speed after each working operation. Longer periods running at full throttle without loading the engine (that is without resistance, which the engine feels from the cutting equipment when trimming) can lead to serious engine damage. ...
-
Husqvarna 322L - page 10
10 – English SAFETY INSTR UCTIONS Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. NOTE! This technique increases the wear on the cord. • The cord wears quicker and must be fed forward ...
-
Husqvarna 322L - page 11
English – 11 WHA T IS WHA T? What is what on the trimmer? 1. T rimmer head 2. Gr ease filler cap 3. Angle gear 4. Spray guar d 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. C ylinder cov er 11. S tarter handle 12. F uel tank 13. Choke 14. Air purge 15. Air filter co ver 16. Clutch co ver 17. Handlebar adjustme ...
-
Husqvarna 322L - page 12
12 – English ASSEMBL Y Assembl y of the trimmer head ! W ARNING! Under no circumstances ma y the cutting equipment be used without an appro ved guard fitted. See the chapter “ T echnical data ” . If the wrong guard or a def ective guard is fitted this can cause serious personal injury . Assembling the loop handlebar (322L, 325L-X/L-XT) Assemb ...
-
Husqvarna 322L - page 13
English – 13 ASSEMBL Y Fitting the spra y guard and trimmer head (322C) Guard • Fit the guard as shown in the diagram. Tighten securely. Trimmer head • Fit the dust cup on the shaft. The nut must be completely covered by the dust cup. • Hold the dust cup with a spanner to prevent the shaft from rotating. • Screw the trimmer head onto the ...
-
Husqvarna 322L - page 14
14 – English Fitting the spra y guard and trimmer head (325CX) • Fit the guard as shown in the diagram. Tighten securely. • Insert the locking pin into the hole to lock the axle. • Screw the trimmer head onto the shaft. Tighten securely. ...
-
Husqvarna 322L - page 15
English – 15 FUEL HANDLING Fuel mixture ! W ARNING! Alwa ys provide good ventilation when handling fuel. NO TE! The machine is fitted with a two-stroke engine and must always be run on a mixture of gasoline and two-stroke oil. I t is important to measure the quantity of oil accurately , to ensur e the correct mixtur e ratio. Small discr epancies ...
-
Husqvarna 322L - page 16
16 – English ST AR T AND ST OP Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PUR GE: P ress the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Warm engine U se the same starting procedure as for the cold ...
-
Husqvarna 322L - page 17
English – 17 Fine adjustment • When the machine has been ” run-in ” the carburetor should be finely adjusted. The fine adjustment should be carried out by qualified person. First adjust the L-jet, then the idling screw T and then the H-jet. Conditions • Before any adjustments are made the airfilter should be clean and the airfilter cover ...
-
Husqvarna 322L - page 18
18 – English Correctly adjusted carburetor A correctly adjusted carbur etor means that the machine accelerates without hesitation and the machine 4-cycles a little at max speed. F urthermor e, the cutting attachment must not rotate/mo ve at idling. A too lean adjusted low speed needle L may cause starting difficulties and bad acceleration. A too ...
-
Husqvarna 322L - page 19
English – 19 MAINTENANCE Cooling system T o maintain as low opera- ting temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4. Cylinder cover (leads cold air onto the cylinder). Muffler NO TE! So ...
-
Husqvarna 322L - page 20
20 – English MAINTENANCE NO TE: Use only HUSQ V ARNA replacement parts. U se of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Y our warranty does not cov er damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQ V ARNA. Maintenance schedul ...
-
Husqvarna 322L - page 21
English – 21 TECHNICAL D A T A 325L-X/L-XT 1,50/24,5 1,34/34 1,06/27 11 000 - 11 700 2 700 8 014 0,9 kW/ 9 000 rpm Ye s Ye s W albr o MB 20 Champion R CJ 7Y 0,02/0,5 Zama C1Q 1,06/0,5 9.0/4,1 L-XT : 9,7/4,4 92/98 109/109 1,5/1,4 L-XT : 1,5/1,4 2,0/1,8 L-XT : 2,4/2,2 2,5/4,8 L-XT : 2,5/4,8 4,9/8,0 L-XT : 5,8/7,6 T echnical data Engine C ylinder ca ...
-
Husqvarna 322L - page 22
22 – English 325CX 1,50/24,5 1,34/34 1,06/27 11 000 - 11 700 2 700 11 700 0,9 kW/ 9 000 rpm Ye s – W albro MB 20 Champion R CJ 7Y 0,02/0,5 Zama C1Q 1,06/0,5 9,3/4,2 92/97 107/108 2,5/2,1 3,2/2,2 4,4/4,2 6,2/8,4 T echnical data Engine Cylinder capacity , cu. in/cm 3 Cylinder bor e, inch/mm S troke length, inch/mm Recommended max. speed, rpm I dl ...
-
Husqvarna 322L - page 23
English – 23 EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 1999 and later small nonroad engine. In U.S., new small nonroad engines must be des ...
-
Husqvarna 322L - page 24
24 – English 1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm ...
-
Husqvarna 322L - page 25
English – 25 1 T ri Cut 2 3 4 5 6 7 8 >20mm >20mm ! B A 6 Nm X 10 ...
-
Husqvarna 322L - page 26
26 – English 1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6" ...
-
Husqvarna 322L - page 27
English – 27 1 T rimmy Hit 23 4 5 6 7 8 9 10 11 “ Click ” “ Click ” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6 ...
-
Husqvarna 322L - page 28
28 – English 1 T rimmy Hit Junior 2 5 6 7 8 9 10 12 “ Click ” 3 4 5,75 m 19' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 2,8 m 9' 1.) 2.) 11 15 cm 6" 15 cm 6" ...
-
Husqvarna 322L - page 29
English – 29 1 T rimmy Hit Pro 2 5 6 7 8 9 10 12 “ Click ” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6" ...
-
Husqvarna 322L - page 30
30 – English 1 T rimmy Hit VI 2 5 6 3 4 7 8 9 10 11 “ Click ” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6 ...
-
Husqvarna 322L - page 31
English – 31 1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII ...
-
Husqvarna 322L - page 32
32 – English ~ 15 cm 6' N ~ 15 cm 6' 502 25 56-01 502 26 04-01 502 25 53-01 502 26 24-01 (x2) 740 43 14-00 502 25 52-01 502 26 01-01 735 31 19-00 729 53 27-71 (x3) 738 21 03-04 502 26 03-01 502 27 07-01 502 26 86-01 1 23 4 T rimmy SII ...
-
Husqvarna 322L - page 33
English – 33 6" 2) 1) ~ 15 cm 6" 7 8 9 10 11 15 cm 12 3 4 56 7,0 m 23" 2,0- mm , 080-." 12 cm 5" ~ 3,5 m 1 1" T rimmy VII ...
-
Husqvarna 322L - page 34
34 – English ´*313¶5r¨ ...
-
Husqvarna 322L - page 35
English – 35 ...
-
Husqvarna 322L - page 36
2001W15 ´*313¶5r¨ ...
¿Tienes una pregunta acerca de Husqvarna 322L?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Husqvarna 322L, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Husqvarna 322L probablemente compartirá una forma de solucionarlo.