-
Porter-Cable FCN200 - page 1
FLOORING CLEA T NAILER Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT ...
-
Porter-Cable FCN200 - page 2
IMPORT ANT SAFETY INSTRUCTIONS WARNING: When using pneumatic tools, basic safety precautions should always be followed to reduce the risk of personal injury, including the following: READ AND FOLLOW ALL INSTRUCTIONS. There are certain applications for which this tool was designed. Porter-Cable strongly recommends that this tool NOT be modified and/ ...
-
Porter-Cable FCN200 - page 3
3 9 . DISCONNECT TOOL FROM AIR SUPPLY HOSE before doing tool maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, handing the tool to another person, or making adjustments. Fig. 5. 1 0 . NEVER USE A TOOL that is leaking air, has missing or damaged parts, or requires repair. Make sure all screws and caps are s ...
-
Porter-Cable FCN200 - page 4
4 1 7 . REMOVE FINGER FROM TRIGGER when not driving fasteners. Never carry tool with finger on trigger: tool will fire a fastener if rubber cap is bumped while trigger is depressed. Fig. 10. 18. USE THE MALLET TO RACK THE WOOD STRIP, NOT THE NAILER . Fig. 11. 19. DO NOT USE THE METAL END OF THE MALLET TO STRIKE THE PLUNGER, use the rubber capped en ...
-
Porter-Cable FCN200 - page 5
5 EMPLOYER’S RESPONSIBILITIES WARNING: Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and follow all of these instructions carefully. OPERA TING INS ...
-
Porter-Cable FCN200 - page 6
Disconnect tool from air supply before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, handing the tool to another person, or making adjustments. PREP ARING THE TOOL 1. After reading and understanding this entire manual, connect tool to air supply (see Fig. 15). WARNING: Keep tool pointed away ...
-
Porter-Cable FCN200 - page 7
7 USING THE TOOL Complete all steps of PREPARING THE TOOL before using the tool. First position and closely fit together (rack) the flooring strip with the (metal) mallet. Position the tool on the tongued edge of the flooring strip (see Fig. 18) aligning the driver guide against the front of the flooring strip. Pull and hold the trigger and strike ...
-
Porter-Cable FCN200 - page 8
8 WARNING: Never attempt to drive a fastener into material that is too hard. The fastener can ricochet causing personal injury. WARNING: Disconnect tool from air supply before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, handing the tool to another person, making adjustments. WARNING: Clean ...
-
Porter-Cable FCN200 - page 9
9 MAINTENANCE CLEAN AND INSPECT DAIL Y CAUTION: Disconnect tool from air supply before cleaning and inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK tool with cleaning solutions. Such solu ...
-
Porter-Cable FCN200 - page 10
10 TROUBLESHOOTING CAUTION: Disconnect tool from air supply before performing any Service Procedure. SYMPTOM PROBLEMS SOLUTIONS 1. Air leak near top of Loose screws. Tighten screws. tool or in trigger area. Worn or damaged Install “OVERHAUL” Maintenance Kit. o-rings or seals. 2. Tool does nothing or Inadequate air supply. Verify adequate air su ...
-
Porter-Cable FCN200 - page 11
11 A CCESSORIES A complete line of accessories is available from your Porter-Cable · Delta Supplier, Porter-Cable · Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. WARNING: Since accessories, other than those offered ...
-
Porter-Cable FCN200 - page 12
12 PORTER-CABLE LIMITED ONE YEAR W ARRANTY Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material ...
-
Porter-Cable FCN200 - page 13
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): BAMMER ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER-CABLE ® , QUICKSAND ® , SANDTRAP ® , S ...
¿Tienes una pregunta acerca de Porter-Cable FCN200?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Porter-Cable FCN200, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Porter-Cable FCN200 probablemente compartirá una forma de solucionarlo.