-
Porter-Cable 7724 - page 1
The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. _______________________________________ T ype No. ________________________________________ Serial No. _______________________________________ Part No. 902452 - 02-02-05 IMPORT ANT Please ma ...
-
Porter-Cable 7724 - page 2
2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could result in serious injury and pr operty damage. There ...
-
Porter-Cable 7724 - page 3
3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer , birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry pr ...
-
Porter-Cable 7724 - page 4
4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fir e and/or serious injury . The term "power tool" in all of the war nings listed below refers to your mains-operated (cor ded) power tool or battery-operated (cordless) power tool. SA VE THESE INSTRUCTIONS 1) W ork area safety a) Keep ...
-
Porter-Cable 7724 - page 5
5 d) Remove any adjusting key or wrench befor e tur ning the power tool on. A wrench or a key left attached to a r otating part of the power tool may result in personal injury . e) Do not overreach. Keep pr oper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress pr operly . Do not wear ...
-
Porter-Cable 7724 - page 6
6 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cor d. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator . 2. Keep blades sharp. Sharp blades will do the job better and safer . 3. Keep hands away from cutti ...
-
Porter-Cable 7724 - page 7
7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litres g ........................ grams kg ........... ...
-
Porter-Cable 7724 - page 8
8 EXTENSION CORD SELECTION If an extension cord is used, make sur e the conductor size is lar ge enough to prevent excessive voltage dr op which will cause loss of power and possible motor damage. A table of recommended extension cor d sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 23 ...
-
Porter-Cable 7724 - page 9
9 TO ST ART AND STOP SA W 1. Make sure power cir cuit voltage is the same as that shown on the specification plate on the saw . Connect machine to power circuit. 2. Squeeze trigger switch (A) Fig. 1, to start motor . Release trigger to stop motor . 3. A lock button (B), Fig. 1, is provided to keep the saw running without holding the switch trigger ...
-
Porter-Cable 7724 - page 10
10 WHICH BLADE TO USE In general, select a blade which will allow at least two teeth to be engaged in the material thickness. The thinner or the harder the material, the finer the blade teeth. The thicker or the softer the material, the coarser the blade teeth. The hi-speed steel blades stay sharp longer than alloy steel blades. USE OF LUBRICANTS N ...
-
Porter-Cable 7724 - page 11
11 TO ADJUST BLADE TRACKING This Band Saw is equipped with an adjustable Blade T racking Mechanism. When properly adjusted: the back edge of the blade will run lightly against at least one of the back-up rollers, but will not pr ess heavily against the roller . If the blade fails to track correctly , adjust as follows: 1. DISCONNECT TOOL FROM POWER ...
-
Porter-Cable 7724 - page 12
12 HOW TO USE A PORT ABLE BAND SA W 1. V erify material to be cut is firmly held to prevent movement. 2. Set variable speed switch in desired position. Speed CAN be changed while machine is running. 3. Hold the saw as shown in Fig. 4, with the work stop (A) contacting the work and blade teeth clear of the work. 4. T ur n saw “ON” and lower onto ...
-
Porter-Cable 7724 - page 13
13 BRUSH INSPECTION (If applicable) For your continued safety and electrical protection, brush inspection and replacement on this tool should ONL Y be performed by an AUTHORIZED PORTER-CABLE SER VICE ST A TION or a PORTER-CABLE • DEL T A F ACTORY SERVICE CENTER. At approximately 100 hours of use, take or send your tool to your near est authorized ...
-
Porter-Cable 7724 - page 14
14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase. W e will repair or replace at our option, any part or parts of the pr oduct and accessories covered under this warranty which, after examination, proves to be defective in workmanship or materia ...
-
Porter-Cable 7724 - page 15
The following are trademarks of PORTER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T AC ...
¿Tienes una pregunta acerca de Porter-Cable 7724?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Porter-Cable 7724, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Porter-Cable 7724 probablemente compartirá una forma de solucionarlo.