-
Stamina Inmotions - page 1
45-1002 ST AMINA PRODUCTS MADE IN CHINA Product May V ary Slightly From Pictured. 2005, 12 Exercise ca n present a health risk. Con sult a physici a n bef ore beginning a ny exercise progra m with this equipment. If you feel faint or dizzy , i mmediately discontinue use of this equi pment. Serious bodily injury ca n occur if this equi pment is not ...
-
Stamina Inmotions - page 2
T ABLE OF CONTENTS SAFETY INSTRUCTIONS T o reduce the risk of serious in jury , rea d the following Safety In struction s before using the InMotion TM II T re a dmill. W AR NING: Before starting a ny exercise or conditioning progra m you should consult with your personal physici a n to see if you require a complete physical exa m. This is espe cial ...
-
Stamina Inmotions - page 3
THAN K YOU FOR PURCHASING THE InMotion TM II T re admill T o help you get started, we have pre-a sse mbled most of your InMotion TM II T rea dmill at the fa ctory with the exception of those few parts left un a sse mbled for shi pping purpose s. Simply f ollow the few a ssembly in structions set f orth in this ma nual. Within a few minute s you wil ...
-
Stamina Inmotions - page 4
BEFORE YOU BEGIN Thank you f or choosing the InMotion TM II T re admill. W e ta ke great pride in producing this quality product a nd hope it will provide ma ny hours of quality exercise to ma ke you feel better , look better a nd enjoy life to its fullest. Y e s, it's a proven fa ct that a regular exercise progra m can i mprove your physical ...
-
Stamina Inmotions - page 5
5 Part No. and De scription Qty HAR D W ARE IDENTIFICA TION CHA T Pla ce wa shers, the end of bolts or screws on the circles to check f or the correct size. Use the small scale to check the size s of bolts a nd screws. This chart is provided to help identify the hardware used in the a ssembly process. After unpa cking the unit, open the hardware ba ...
-
Stamina Inmotions - page 6
Pla ce all parts from the box in a cleared area a nd position them on the floor in front of you. Re move all pa cking materials from your are a and pla ce the m ba ck into the box. Do not dispose of the pa cking materials until a ssembly is completed. Read e a ch step carefully before beginning. If you are missing a part ple a se call our toll-free ...
-
Stamina Inmotions - page 7
ASSEMBL Y INSTRUCTIONS 7 STEP 3: Pla ce the BASE FRAME(1) between the LEFT a nd RIGHT UPRIGHTS(2, 3) a nd secure with HEX BOL TS(M12 x 70mm)(39) a nd W ASHERS(M12)(48). DO NOT TIGHTEN COMPLETEL Y . STEP 4: Secure the U-SHAPED HAND RAIL(5) onto the LEFT a nd RIGHT UPRIGHTS(2, 3) with BUTTON HEAD BOL TS(6mm x 15mm)(40) a nd ARC W ASHERS(M6)(44). Conn ...
-
Stamina Inmotions - page 8
USING THE ELECTRONIC METER W alking Belt movement or push the button. Automatic shut off after 4 minute s of ina ctivity . POWER OFF : POWER ON : AA Batterie s MODE / CLEAR BUTTON: Press a nd relea se to select functions. Press a nd hold f or three seconds to reset all functions to zero. SCAN: TIME: SPEED: DIST ANCE: CALORIES: Automatically sca ns ...
-
Stamina Inmotions - page 9
The ba sic ide a behind the manual tre admill is to have the belt running on a trea dmill board and between two rollers so that the belt will move without much eff ort. In order for the belt to run smoothly , there are a few points that need to be noted. TREADMILL ADJUSTMENTS BEL T ALIGNMENT The belt must be in the center of the trea dmill to preve ...
-
Stamina Inmotions - page 10
TREADMILL ADJUSTMENTS W ALKING RESIST ANCE The walking re sista nce or eff ort needed to push the trea dmill belt ca n be adjusted by cha nging the incline a ngle. This tre a dmill ha s two adjustment positions. Lowe st Re sista nce Remove (unscrew) the BUMPER ST ANDS(22) from the bottom of the trea dmill a nd store them in the end of the trea dmil ...
-
Stamina Inmotions - page 11
STORAGE 11 T o store the InMotion TM II T re admill si mply keep it in a cle a n dry place. T o avoid da mage to the electronics meter , remove the batteries bef ore storing the InMotion TM II T re a dmill f or one ye ar or more. Follow the following proce ss to fold The InMotion TM II T re a dmill a s illustrated for ea sy storage. 1. 2. 3. 4. UNF ...
-
Stamina Inmotions - page 12
PRODUCT P ARTS DR A WING 12 FRONT BACK Belt Guides ...
-
Stamina Inmotions - page 13
P ARTS LIST DIAGRAM# P ART NAME QTY 13 1 Ba se Fra me 1 2 Left Upright 1 3 Right Upright 1 4 Upright Support 1 5 U-Sha ped Ha ndrail 1 6 Spring Pin 1 7 Spring 1 8 Ball Knob 1 9 Pull Pin 1 10 Front Roller /w Flywheels 1 1 1 Front Shaft 1 12 Bearing (6000zz) 4 13 Pla stic W a sher (M10) 4 14 Rear Roller 1 15 Rear Shaft 1 16 Adjustment Bra cket 2 17 W ...
-
Stamina Inmotions - page 14
Sta mina Products, Inc. warra nts that this product will be free from defects in materi als a nd workma nshi p under normal use, service a nd proper operation for a period of 90 days on the parts a nd one year on the fra me from the date of the original purcha se from an authorized retailer . THIS W ARRANTY SHALL NOT APPL Y TO ANY PRODUCT WHICH HAS ...
-
Stamina Inmotions - page 15
IMPORT ANT : Before filling out the form below ma ke sure you have the right information. Refer to the parts list to make sure you're ordering the right parts! Detach a nd M ail or Fax the Form Below Sta mina Products, Inc. P .O. Box 1071 Springfield, MO 65801-1071 IMPORT ANT : We must have your phone number in order to proce ss the order! F A ...
¿Tienes una pregunta acerca de Stamina Inmotions?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Stamina Inmotions, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Stamina Inmotions probablemente compartirá una forma de solucionarlo.