-
Audiovox AA-RS10CS - page 1
Kit Contents AA-RS10CS Control Module (2) - 3 Button Anti Code Grabbing Transmitters 3 Channel Code Learning Receiver External Superheterodyne Antenna/Receiver (1) - Multi Pin Input/Output Harness (1) - Six Pin Power Harness (1) - Four Pin Auxiliary Harness (1) - Two Pin I/O Harness (1) - Accessory 2 Pin Connector (1) - 2 Pin Door Lock Harness (2) ...
-
Audiovox AA-RS10CS - page 2
The AA-RS10CS Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug pre-heat which may be required for certain diesel vehicles, (see selectable feature #9). If the diesel engine has a instant fire, (no glow plug ...
-
Audiovox AA-RS10CS - page 3
Page 3 WIRING THE 6 PIN MAIN POWER HARNESS: RED w/ WHITE T race Wire: + 12 volt Battery 1 Source Connect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse and holder provided. This wire provides power for the control circuit as well as the ignition 1 and ignition 2 relays. RED Wire: + 12 V olt ...
-
Audiovox AA-RS10CS - page 4
Page 4 BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the to the "ON" or "RUN" and the "ST ART" or CRANK" positions, and will have 0 volts when the key is turned to the "OFF" and "ACCESS ...
-
Audiovox AA-RS10CS - page 5
Page 5 GREY Wire: Negative Inhibit Input 1 Connect the GREY wire to the previously mounted hood pin switch provided . This wire will be routed through the fire wall into the engine compartment. It is necessary to use an existing grommet when passing wires through the fire wall to prevent short circuiting. This is an important safety feature of APS ...
-
Audiovox AA-RS10CS - page 6
Page 6 (2) WHITE Wires: Parking Light Flasher These wires are the COMMON and NORMALLY OPEN contacts of the on-board parking lamp relay. If the vehicle's parking lights are a +12 volt switched system, connect (1) of the White wires to a fused (15A max.) +12 volt battery source, and connect the second White wire to the vehicle's parking lig ...
-
Audiovox AA-RS10CS - page 7
Page 7 4. Cut (#1) wire (as shown), and connect the ignition switch side of the cut wire to terminal #87a of the relay . Connect the other side of the (#1) wire to terminal #30. 5. Connect the previously selected resistor from terminal #87 to the second (#2) wire (as shown). NOTE: The above information and following diagram is for the GM V A TS sys ...
-
Audiovox AA-RS10CS - page 8
Page 8 In this application, the Red wire of the two pin harness provides a ground pulse during the arming sequence, or pulsed ground lock output. Connect the Red wire to the low current ground signal wire from the factory door lock switch to the factory door lock relay . The Green wire of the two pin harness provides a ground pulse during the disar ...
-
Audiovox AA-RS10CS - page 9
Page 9 Audiovox AS-9159 Door Lock Interface, (or equivalent 30 A automotive relays) must be used. Refer to the Audiovox Door Lock Wiring Supplement for proper wiring of these circuits. 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock Control Circuits In these applications, the AS 9159 Door Lock Interface ( or equivalent 30 A automo ...
-
Audiovox AA-RS10CS - page 10
Page 10 Feature Selection 1 Flash 2 Flashes Default First 1 Second Door Locks 3.5 Second Door Locks 1 Second Second 10 Minute Run Time 15 Minute Run Time 10 Minute Third Park Lights Steady On Park Lights Flash Steady Fourth (No Function) Tach Operation Tach Fifth (No Function) (No Function) ------------ Sixth Ign. 2 Off During Crank Ign. 2 On Durin ...
-
Audiovox AA-RS10CS - page 11
Page 11 and or single injector. To learn tach; 1. Start with the programming switch in the OFF position. 2. Turn the ignition key to the ON position. 3. Flip the program switch ON - OFF - ON - OFF - ON - then OFF. 4. Immediately turn the ignition key OFF. 5. Flip the program switch ON, then start the vehicle using the ignition key . 6. When the uni ...
-
Audiovox AA-RS10CS - page 12
Page 12 2. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coil pack. For 8 cylinder , four coil systems, connect to any of the three coils. 3. Connect the Y ellow wire to a +12 volt ignition 1 source. This wire will have +12 volts with the ignition in the on and start position and have 0 volts w ...
-
Audiovox AA-RS10CS - page 13
Page 13 4. Sitting in the vehicle, start the engine using the vehicle's ignition key . 5. Step on the brake pedal and shift the gear selector into reverse. 6. Allow the transmission to shift. When you feel the engine pull, do not move the gear selector just turn the ignition switch off. DO NOT attempt to remove the key . 7. Keeping the brake p ...
-
Audiovox AA-RS10CS - page 14
Page 14 KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available. Although not preferred, the vehicle Key In Sensor may be re-configured to allow a margin of safety and will prevent the vehicle with a Mechanical Neutral Start Switch from starting in gea ...
-
Audiovox AA-RS10CS - page 15
Page 15 Remote Start Unit as shown below . METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chi ...
-
Audiovox AA-RS10CS - page 16
WIRING DIAGRAM © 2000 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-5850 ...
¿Tienes una pregunta acerca de Audiovox AA-RS10CS?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Audiovox AA-RS10CS, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Audiovox AA-RS10CS probablemente compartirá una forma de solucionarlo.