Español dropdown-ico

Manual de instrucciones Graco 262605

28 de páginas 6.74 mb
Descargar

Pasar a la página of 28

Summary
  • Graco 262605 - page 1

    3A1456D Operation EasyMax ™ WP Cor dless P aint Spra y er U .S. Pate nt 6,619,569; D630,708S and othe r patents pendin g Communit y Design Registration No. 0012282 55; India P atent No. 230058 China P atent No. ZL201030238 948.3; T aiwan P atent No. 142952 - For portable spray applications of wate r -based arc hitectural paints and coatings only ...

  • Graco 262605 - page 2

    Table of Contents 2 3A1456D T able of Contents W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Component Ident ification . . . . . . . . . . . . . . . . . . . . . . . . . 5 Common Pr ocedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pressure Relief Procedure . . . . . . . . . . . . . . . . . ...

  • Graco 262605 - page 3

    Warnings 3A1456D 3 Wa r n i n g s The follo wing war nings are for the setup, use, ma intenance, and repair of this equipment. Th e e xclamatio n point symbol aler ts y ou to a general warning and the ha zard symbols refer to procedure-sp ecific risks. When these symbols appear in the body of thi s manual, ref er back to these W ar nings. Product-s ...

  • Graco 262605 - page 4

    Warnings 4 3A1456D B A TTER Y HAZARD The batter y may leak, e xplode, cause b ur ns, or cause an explosion if mishandled. Contents of an open battery can cause se vere irritation and/or chemical burns. If on skin, wash with soap and w ater . If in ey es, flush with water f or at least 15 minutes and seek immediate medical attention. • Do not shor ...

  • Graco 262605 - page 5

    Component Identification 3A1456D 5 Component Identification *NO TE: Filter asse mbly is re verse-threade d. T ur n left (or co unter-clockwise) to tigh ten, tur n rig ht (or clockwise) to loo sen. ti15479a D Fa E R J K C Y T S W B D N A Fa Fb P H G M Z A Cordless Paint Spra yer B Spra yer Hook C Outlet V alve Repair Access D Spra y Tip/Guard Assemb ...

  • Graco 262605 - page 6

    Common Procedures 6 3A1456D Common Pr ocedures Pressure Relief Pr ocedure 1. Engage tr igger lock. 2. Put control valve UP to release pres sure. Tr i g g e r L o c k Spra y Tip P osition Contr ol V alve P osition Do not opera te or spra y near children. Do not aim the spra yer at, or spra y any person or animal. K eep hands and other body par ts aw ...

  • Graco 262605 - page 7

    Charging the Battery 3A1456D 7 Char ging the Batter y Batteries are initially 50% charge s to provide optimum battery life and requir e charging before first use. It takes approximatel y 45 minutes to charge a dead battery to 80%, at which point it can be used.It will take approxi- mately 75 minutes to fully char ge a dead battery. 1. Slide batter ...

  • Graco 262605 - page 8

    Setup 8 3A1456D Setup Suction T ube Selection This spra yer comes with two diff erent suction tubes. Standar d Suction T ube (spra ys ceilings and walls): When spra ying walls, the inlet of the suction tube should be aimed at the fr ont of the material cup . When spra ying ceilings , the inlet of the suction tube should be aimed at th e back of the ...

  • Graco 262605 - page 9

    Setup 3A1456D 9 Spra ying Stains or Clear Coats (Fine-Finish Optimizer) The Fine-Finish Optimizer should be installed an d used when spraying thin materi al such as stain or clear coats. The Fine-Finish Op timizer restricts the mat er ial flow resulting in a finer quality finish. Installation 1. Remove material cup and suctio n tube. 2. Push Fine-F ...

  • Graco 262605 - page 10

    Setup 10 3A1456D Materials NO TE: Wh en sprayin g water-bas ed materials, flush the spra yer th oroughly with water . Star ting a New Job (or Refilling the Cup) 1. Engage trigger lock and put prime/relief valv e UP to release pressure. 2. Use the Fine-F inish Optimizer cleaning tool to lightly push on inlet v alve to mak e sure it mov es up and dow ...

  • Graco 262605 - page 11

    Setup 3A1456D 11 Install Tip/Guar d Assembly (if not installed) Rever sible Tip Selection Chart 1. Engage trigger lock and put prime/relief valv e UP to release pressure . Then remove Tip/Guard Assemb ly . 2. Install filter to Spra y Tip/Guard Assembly (make sure filter is fully installed into spra yer). NO TE: Filter ass em- bly is re v erse-threa ...

  • Graco 262605 - page 12

    Setup 12 3A1456D Basic Spra ying T echniques NO TE: Use a piece of scrap cardboa rd to practice these basic spra ying techniques bef ore you begin spr ayi ng the surf ace. Anything y ou don’t want painted that is in the area of your spraying surface shou ld be covered or remo ved. Hold spra ye r at least 25 cm (10 in .) from surf ace and adjust a ...

  • Graco 262605 - page 13

    Unclogging Spray Tip/Guard Assembly 3A1456D 13 Unc logging Spra y Tip/Guar d Assembl y Occasionally , debris from material can accumulate and clog the spra y tip. P erf or m the fo llowing steps to unclog the tip . 1. T o unclog tip obstr uction, en gage trig ger lock and pull relief valv e UP to release pressure. 2. Re verse spra y tip to UNCLOG p ...

  • Graco 262605 - page 14

    Shutdown and Cleaning 14 3A1456D Shutdo wn and Cleaning Flushing Spra yer 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remo ve material cup and properly dispose cup liner or e xcess material. 3. Remo ve and clean sp ray er intak e tube and screen with wat er (or flushing fluid) and a brush e v er y time you flush the sp ...

  • Graco 262605 - page 15

    Shutdown and Cleaning 3A1456D 15 6. Disconnect trigger loc k and trigger spra yer f or appro ximately 15 se conds. Engage trigger loc k. 7. Discard contaminated fluid and refill with appropr i- ate flushing fluid. 8. Disengage trigger loc k, re verse tip to UNCLOG position, an d pull tr igger for 5 seconds to prime spra yer . 9. Put prime/relief v ...

  • Graco 262605 - page 16

    Storage 16 3A1456D Cleaning Spra yer Exterior • Wipe paint off outside of spray er using a soft cloth moistened with w ater or flushing fluid . Do NO T submerge the spra yer . Tips • Tips will require replac ement depending on abrasiveness of paint. • Do not spra y with worn tip . See T roub leshooting , page 21. Storage 1. Dilute 4 oz. of Pu ...

  • Graco 262605 - page 17

    Replacement Parts and Kits 3A1456D 17 Replacement P ar ts and Kits 1 8 11 6 5 4 3 7 12 16 ti15497a 2 15 14 17 10 18 9 19 21 20 22 13a 13 13a 13 Ref. P art Description 1 262583 Spray er , replacement (no tip , battery , suction tube , or material cup) 2 16D562 Liner , replacement (10 pac k) 3 24F045 Fine Finish Opti mizer (with Cleaning T ool) 2-P a ...

  • Graco 262605 - page 18

    Repair Kit 18 3A1456D Repair Kit Outlet V alve Fitting NO TE: Before doing any repair to pump, perf or m Flushing Spra yer procedure , page 14. Re m ova l 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remove battery . 3. Remove pump outlet cap . 4. Use tool (sup plied) to loosen and remov e outlet valv e fitting. Install ...

  • Graco 262605 - page 19

    Alternate Priming Method 3A1456D 19 Alternate Priming Method 1. Engage tr igger lock and put p rim e/relief valve UP to release pressure . 2. Remov e material cup and f ill with flushing mater ial. 3. With spray er in pr ime mode, tur n s pra yer upside-down, remov e strainer and slowly po ur flush- ing mater ial into the intake tube u ntil full. 4 ...

  • Graco 262605 - page 20

    Alternate Priming Method 20 3A1456D Inlet V alve Cleaning Re m ova l 1. Engage trigger lock and pull relief v alve UP to release pressure . 2. Remove material cup and suctio n tube. 3. Hold spr ay er upside-down and use wrench or sock et to loo sen and remove inlet fitting, inlet valv e, and spring. NO TE: Make sure the spring also comes out. U se ...

  • Graco 262605 - page 21

    Troubleshooting 3A1456D 21 T roub leshooting Chec k ev er ything in this T roubleshooting T able bef ore you br ing the spra ye r to an authorized serv ice center . Prob lem Cause Solution Spra yer mak es no sound when trigger is pulled T rigger is locked. Disengage trigger lock. See page 6. Status Indicator Light is solid RED when trig- gering, in ...

  • Graco 262605 - page 22

    Troubleshooti ng 22 3A1456D Spra y Pattern Dia gnostics Spra ys with poor results Tip is pa r tially c logged See Unclog ging Tip/Guard Assembl y , page 13. Tip is not in corre ct position Rotate tip to SPR A Y po sition. Incorrect tip for application of material. See Rev ersible Tip Selection Chart, page 11. Tip filter is par tially clogged Clean ...

  • Graco 262605 - page 23

    Troubleshooting 3A1456D 23 Spra y patter n is too narrow: Spra yer is too close to target surface . Incorrect tip for application of material. Tip is wor n or damaged. Mov e spra yer aw ay from surf ace (10 in). See Rever sible Tip Selection Chart, page 11. Replace tip . See Install Tip/Gua rd Assembl y , page 11. Spra y patter n is too wide: Spra ...

  • Graco 262605 - page 24

    Technical Data 24 3A1456D T e c hnical Data Sprayer: Maximum working pressure 2000 psi (137.8 bar , 13.7 MPa) W eight 6.32 lb (2.87 kg) Dimensions: Length 13.25 in. (33.6 cm) Width 5.0 in. (12.7 cm) Height 10.375 in. (33.9 cm) Storage temperature r ange ◆❖ 32° to 122°F (0° to 50°C) Operating temperature r ange ✔ 40° to 90° F (4° to 32? ...

  • Graco 262605 - page 25

    Notes 3A1456D 25 Notes ...

  • Graco 262605 - page 26

    Notes 26 3A1456D Notes ...

  • Graco 262605 - page 27

    Notes 3A1456D 27 Notes ...

  • Graco 262605 - page 28

    All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions. T his manual contains English. MM 3 A1456 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Kor ...

Fabricante Graco Categoría Paint Sprayer

Los documentos del dispositivo Graco 262605 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Graco
- manuales de instrucciones 262605
- hojas de producto Graco
- folletos informativos
- o etiquetas energéticas Graco 262605
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Graco 262605.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Graco 262605, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Graco 262605. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Graco 262605.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Graco 262605, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Graco 262605. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Graco 262605.

El manual de instrucciones completo de Graco debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Graco 262605 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Graco 262605, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Graco 262605 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Graco 262605 - que deben facilitarnos los primeros pasos durante el uso de Graco 262605
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Graco 262605
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Graco 262605 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Graco 262605?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Graco 262605, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Graco 262605 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)