Español dropdown-ico

Manual de instrucciones Sears 113.21371

24 de páginas 2.18 mb
Descargar

Pasar a la página of 24

Summary
  • Sears 113.21371 - page 1

    MODEL NO. ]]3.21371 DRILL PRESS ONLY 113.213710 DRI LL PRESS WITH 1/2 HP MOTOR Serial Number ...................... Model and serial number may be found at the rear of the head. You should record both model and serial number in a safe place for future use. CAUTION: Read GENERAL and ADDITIONAL SAFETY INSTRUCTIONS carefully ® 15-1/2 INCH DRILL PRESS ...

  • Sears 113.21371 - page 2

    FULL ONE YEAR WARRANTY ON CRAFTSMAN DRILL PRESS If within one year from the date of purchase, this Craftsman Drill Press fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES. This warranty give ...

  • Sears 113.21371 - page 3

    additionam safety instructions for drill presses WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT TO OPERATE YOUR DRILL PRESS UNTIL iT IS COMPLETELY ASSEMBLED AND iNSTALLED ACCORDING TO THE INSTRUCTOONS . .. AND UNTaL YOU HAVE READ AND UNDERSTAND THE FOLLOWING: 1. 2. 3. 4. 5. 6. 7. 8. 9. General Safety instructions for Power Tools Page 2 Getting to Kno ...

  • Sears 113.21371 - page 4

    additional safety instructions for drill presses WEAR YOUR The operation of any power tool can result in foreign objects being thrown into the _yes, which can result in severe eye damage. Always wear safety goggles complying with ANSI Z87,1 (shown on Package) before commencing power tool operation. Safety Goggles are available at Sears retail or ca ...

  • Sears 113.21371 - page 5

    motor specifications and electrical requirements MOTOR SPECRFICATIONS This drill press is designed to use a 1725 RPM motor only. Do not use any motor that runs faster than 1725 RPM. It is wired for operation on 1!0-120 volts, 60 Hz., alternating current. IT MUST NOT BE CONVERTED TO OPERATE ON 230 VOLTS, EVEN THOUGH THE RECOMMENDED MOTORS ARE DUAL V ...

  • Sears 113.21371 - page 6

    assembly WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETED, 1. Unwind the power cord. 2. Make sure the quill lock handle is tight. 3. Stand on, the left side of the drill press and LOOSEN the HEAD LOCK HANDLE. 4. Raise the HEAD about HALF WAY up the column. CAUTION: THE HEAD WEIGHS ABOUT ...

  • Sears 113.21371 - page 7

    SPINDLE NOSE LOCKING COLLAR 2. Apply a light film of oil such as Sears household oil to the spindle nose. 3. Place the chuck on the spindle nose and screw the locking collar up as far as it will go. CHUCK 4. Insert a piece of 1/4" dia. STEEL ROD in to one of the holes in the chuck body. 5. Insert the CHUCK KEY into one of the holes in the coll ...

  • Sears 113.21371 - page 8

    assembly INSTALLING THE DEPTH STOP 1. Screw the THUMB SCREW partways into the DEPTH POINTER. 2. Place the DEPTH POINTER SHOE inside the pointer. 3. Loosen QUILL LOCK HANDLE ... lower the quill about two inches. 4. Slide the pointer and shoe onto the FEED STOP ROD and tighten the thumb screw. Make sure the pointer is positioned as shown, 5. Screw th ...

  • Sears 113.21371 - page 9

    9. Gently push down on the FEED HANDLES until the head raises upwards as far as it will go. 10, TIGHTEN THE HEAD LOCK HANDLE AND THE QUILL LOCK HANDLE. 11. HOLD onto the Feed Handle and UNLOCK the quill lock handle. 12, Let the quill return to the UP position in the head. !3. TIGHTEN THE QUILL LOCK HANDLE. Repeat steps 3 thru 10 until the head is r ...

  • Sears 113.21371 - page 10

    assembty NOTE: When using motors which have Y2" dia. shafts, place the adapter sleeve (furnished with the motor) on the shaft so that the slot in the sleeve is over the flat spot. 4. Insert the shaft key (furnished with motor) into the grooves in the shaft and pulley so that the end of the key is even with the end of the shaft, 5. Tighten the ...

  • Sears 113.21371 - page 11

    5, Remove the belt guard by "pushing in" on the two "links". 6, Place motor on drill press ... screw the pivot screws into the holes. NOTE: DO NOT SCREW THEM IN TOO TIGHT ,.. EXCESSIVE TIGHTNESS COULD BEND THE MOTOR MOUNT. 7, Find two 5/16 in-18 hex. nuts among the loose parts ... screw them on to the pivot screws ... tighten th ...

  • Sears 113.21371 - page 12

    assembly INSTALLING AND TENSIONING BELT 1. Place a straightedge such as a piece of wood, metal or framing square across the pulleys. 2. Move the motor UPWARDS until the pulleys are IN LINE ... tighten the motor mounting nuts with a ½ in. wrench. 3. 4, 5. 6. 7_ 8. Place the belt on the pulleys. Put a dab of grease such as Sears gear case lubricant ...

  • Sears 113.21371 - page 13

    getting to know your drill press -4.-- SPLINES (GROOVES) SPINDLE QU ILL "_ QUILL AND SPINDLE ASSEMBLY INSIDE OF DRILL PRESS SWITCH KEY CHUCK _,.__... KEY DRILL RACK "ON-OFF" (TEETH) SWITCH CHUCK DEPTH QUIL HANDLE DEPTH POINTER CHUCK LOC! COLLAR SUPPORT COLLAR "THUMB SCREV/ rEED HANDLE LOCK HANDLE TABLE SUPPORT COLLAR HEAD LOCK H ...

  • Sears 113.21371 - page 14

    getting to know your drill press HEAD LOCK HANDLE ... locks the head to the column. ALWAYS have it locked in place while operating the drill press. HEAD SUPPORT COLLAR . .. prevents the head from dropping when the head lock handle is loosened. ALWAYS have the collar LOCKED into position against the UNDERSIDE of the head ..... TABLELOCK HANDLE ,, ; ...

  • Sears 113.21371 - page 15

    REMOVING THE CHUCK. 1, 2. Insert apiece of 1/4 in. alia. steel rod in one of the holes in the chuck body, insert the CHUCK KEY into one of the hoIes in the collar ... turn it in the direction of arrow until LOOSE. Continue to turn it until the chuck is released. "'ON-OFF" SWITCH for drill has Iockinq feature. THIS FEATURE IS INTENDED ...

  • Sears 113.21371 - page 16

    basic drill press operation We recommend the following instructions for operating your drill press so that you get the best results and to minimize the likelihood of personal injury. WARNING: FOR YOUR OWN SAFETY, ALWAYS OBSERVE THE FOLLOWING SAFETY PRECAUTIONS. I. Check spindle speed 2. Before operating, turn the switch "on" then "of ...

  • Sears 113.21371 - page 17

    HOLE LOCAT!ON Make a DENT in the workpiece whereyou want the hole • • . using a CENTER PUNCH or a SHARP NAIL. Before turning the switch ON, bring the drill down to the workpiece lining it up with the hole location. FEEDING Pull down on the feed handles with only enough effort to allow the drill to cut. Feeding TOO SLOWLY might cause the drill t ...

  • Sears 113.21371 - page 18

    maintenance WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "'OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAINING OR LUBRICATING YOUR DRILL PRESS, Frequently blow out any dust that may accumulate inside the motor. A coat of automobile-type wax applied to the table and column will help to keep the surfaces clean. If the power c ...

  • Sears 113.21371 - page 19

    trouble shooting WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING. TROUBLE Noisy Operation Drill Burns. Drill leads off... hole not round. PROBABLE CAUSE 1. Incorrect belt tension 2. Dry Spindle 3. Loose spindle pulley or motor pulley. 1. Incorrect speed 2. Chips not c ...

  • Sears 113.21371 - page 20

    PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.21371 & 113.213710 13 14 (SEE FIGURE 3) i 38 18 52 51 Figure I 37 WIRING DIAGRAM ,=111 _0 Q ...

  • Sears 113.21371 - page 21

    PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.21371 & 113.213710 Always order by Part Number - not by Key Number FIGURE 1 PARTS LIST Key No. 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 35 36 37 Part No. Description 71097 STD 541110 71046 STD 571812 71163 STD 551210 STD 551208 169689 71092 STD 610805 71170 37818 STD ...

  • Sears 113.21371 - page 22

    PARTS LIST FOR CRAFTSMAN DRILL PRESS ,___i_ 5 MODEL NO. 113.21371 & 113.213710 6 4 11-- ,4d; 15-----._ 16,----..-"_ Figure 2 FIGURE 2 PARTS LIST Key Part No. No. Description 1 60049 2 71173 3 144987 4 71069 5 STD 610807 6 60158 7 71071 8 71070 9 71162 10 71072 11 71097 12 60192 13 71089 14 71090 15 STD 315253 16 71091 17 18414 *Screw, Pan ...

  • Sears 113.21371 - page 23

    Q "+-------3 7 / / / / PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.21371 & 113.213710 / / / / / / ,/ / / / / FIGURE 3 - 71075 SPINDLE ASSEMBLY, STOP Key Part No. No. - 71075 1 37158 2 3509 3 71147 4 27813 5 60176 6 27812 7 STD 551125 8 STD 541025 9 38422 10 STD 541237 11 STD 522512 12 71078 13 71077 Description Spindle Assembly, Sto ...

  • Sears 113.21371 - page 24

    SERVICE MODEL NO. 113.2137] DRILL PRESS ONLY 113.2!3710 DRILL PRESS WITH 1/2 HP MOTOR HOW TO ORDER REPAIR PARTS ] 5°]/2 [NCH DRILL PRESS Now that you have purchased your 15-1/2 inch drill press should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide al ...

Fabricante Sears Categoría Drill

Los documentos del dispositivo Sears 113.21371 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Sears
- manuales de instrucciones 113.21371
- hojas de producto Sears
- folletos informativos
- o etiquetas energéticas Sears 113.21371
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Sears 113.21371.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Sears 113.21371, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Sears 113.21371. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Sears 113.21371.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Sears 113.21371, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Sears 113.21371. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Sears 113.21371.

El manual de instrucciones completo de Sears debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Sears 113.21371 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Sears 113.21371, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Sears 113.21371 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Sears 113.21371 - que deben facilitarnos los primeros pasos durante el uso de Sears 113.21371
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Sears 113.21371
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Sears 113.21371 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Sears 113.21371?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sears 113.21371, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sears 113.21371 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)