-
Cannon Mag 20 Dt/Ts - page 1
OWNER’S MANU AL NOTE: Do not return your CANNON® Do wnrigger to your retailer. Your retailer is not authorized t o repair or replace this unit. You may obtain service b y: • calling CANNON® at 1-800-2 27-6433; • returning your do wnrigger to the F actor y Service Center; • sending or taking your d ownrigger to any CANNON® Authorized Serv ...
-
Cannon Mag 20 Dt/Ts - page 2
2 Parts Description 1. Reel This is used to spool the cable, available in length s ranging from 1 50 to 400 feet. 2. Boom This is used to extend the weight out from the body of the downrigger and has a pulley fixed to its end. Boom lengths range from 24 to 53 inches. 3. Swivel Head This relays the cable at the end of the boom to lower the wei ght. ...
-
Cannon Mag 20 Dt/Ts - page 3
3 Mag 20 DT New Features Magnum Power The Mag 20 DT/HS and Mag 20 DT/TS feature improved tolling weight capacity, retrieval rate, and quality. The Mag 20 DTs can now accommodate trolling weights up to 20lbs. The newly improved Mag 20 DTs also feature a high retrieval rate up to 250 feet per minute. Mag 20 DT/TS Features The Mag 20 DT/TS (Tournament ...
-
Cannon Mag 20 Dt/Ts - page 4
4 Downrigger Mounting on Boat s A downrigger should be mounted where ever it is easy to operate and observe. You want to be able to see your fishing rod and to react quickly. So, choosing a good spot to mount your downrigger on your boat is 99% of the job. Due to the great variety of boats available, mounting your downrigger can be a dilemma. Havin ...
-
Cannon Mag 20 Dt/Ts - page 5
5 Side Rail Mounting Side/Rail mounts can be mounted to a welded T section. They can also be used at the two rail section butt joint. In both installations it is recommended to use a non-slip material, such as rubber or a thin wood sheet, between metal surfaces. You can also use these for mounting to a very narrow side gunwale. There is a plate pro ...
-
Cannon Mag 20 Dt/Ts - page 6
6 NOTE: When using the telescopic boom, we strongly recommend the use of a deck plate on all boats to provide adequate stability for the downrigger. The Low-Profile Swivel Base mounting follows the same procedure as for the deck plate except that four 1/4”-20 x 2 1/2" truss head screws are used to fasten the mounting base and four additional ...
-
Cannon Mag 20 Dt/Ts - page 7
7 Mounting the Downrigger on the Base Slide body over the lip of the base, with boom outboard or facing the stern. Lift Lock Knob to hold threaded shaft clear of base until body completely covers base. Turn Lock Knob clockwise to tighten the downrigger to the base. Tip: Periodically check base to ensure integrity. The base should be replaced at lea ...
-
Cannon Mag 20 Dt/Ts - page 8
8 T erminating the Downrigger Cable Cannon Uni-Release The Cannon Uni-Release attaches directly to the downrigger weight. Attach fishing line to the clip at the end of the release, and then click through a series of increasing tension settings. The release can be used with any test line on salt or fresh water and may be adjusted from 2 to 22 pounds ...
-
Cannon Mag 20 Dt/Ts - page 9
9 CAUTION: This rod holder is intended for use of up to 30 lb. test line only, and is not recommended for use with any tackle IGFA rated higher than 30 lb. A safety strap (not included) is recommended for all applications. The rod holder assembly is not warranted when used with tackle above 30 lbs. Equipment placed in the rod holders and the loss t ...
-
Cannon Mag 20 Dt/Ts - page 10
10 Wiring Y our Downrigger Your Boat's Electrical Condition It is important to make sure that your boat is properly set up before installing your Mag 20 DT with Positive Ion Control (PIC). Whenever a boat is in water, various submerged parts interact to create weak electrical currents. These weak electrical currents must be controlled to exten ...
-
Cannon Mag 20 Dt/Ts - page 11
11 FUSE / BREAKER SPECIFICATI ONS: 30 Amp, 32 Volt, waterproof, fast blow. WIRE SPECIFICATIONS: 0-15 ft. (0-5 meters) 10 gauge 15-25 ft. (5-8 meters) 8 gauge 25-30 ft. (8-9 meters) 6 gauge CAUTION: When using wire longer than that provided with your unit, follow the above chart. When running more than 30 feet from the battery, contact a qualified e ...
-
Cannon Mag 20 Dt/Ts - page 12
12 Clutch Knob 3-Position Motor Swit ch Operating Y our Downrigger After mounting the Cannon downrigger to your boat, release some line from your rod and reel so that the lure is anywhere from 5 to 100 feet behind the boat. Tthis is called drop back. Attach the fishing line firmly into the line release. Press and hold the toggle switch down to lowe ...
-
Cannon Mag 20 Dt/Ts - page 13
13 NOTE: Make sure that the clutch is well tightened when using powered descent or ascent. NOTE: Actual fishing depth may vary from depth shown on meter due to trolling speed and weight of cannon ball. (See "Blowback") NOTE: If your reel continues to slip no matter how hard you tighten the brake adjust knob, try this suggestion. 1. Unwind ...
-
Cannon Mag 20 Dt/Ts - page 14
14 The Short S top System The Short Stop system is composed of three critical components: the electronic unit, the reel set screw, and the trolling weight insulat or. While the downrigger cable is in the water, there is a minute electrical current that flow s between the cable and the grounded metal boat components in the water. When the cable clea ...
-
Cannon Mag 20 Dt/Ts - page 15
15 How the Positive Ion Control System Works The PIC system uses an internal circuit that passes the voltage through the drive train of the Mag 20 DT to the reel set screw. The set screw contacts the cable. Care must be taken to ensure contact between the cable and the set screw when replacing the cable. The positive Ion Control system applies a va ...
-
Cannon Mag 20 Dt/Ts - page 16
16 Blowback Simply stated, blowback is what happens to the downrigger weight when you pull it through the water behind your boat. As your speed increases, so does the horizontal distance between the weight and your downrigger. The faster you go, the farther the weight is behind you. The farther the weight is behind you, the shallower the weight is. ...
-
Cannon Mag 20 Dt/Ts - page 17
17 T rouble Shooting PROBLEM: Up or down will not work. SOLUTION: Check the battery cable polarity then check the battery voltage. A properly connected and charged battery is important for safety and for proper operation of the downrigger. PROBLEM: The Mag 20 DT/HS Mag 20 DT/TS fails to continue running after toggle switch is pushed up and held m ...
-
Cannon Mag 20 Dt/Ts - page 18
18 T en Good T r olling Tip s 1) Test your lures over the boat side before sending them down and back. Do this to make sure the lure wiggles and wobbles properly without going belly up or wandering off. Some lures can be adjusted, fine tuned actually, to impart maximum action. For example, a slight bend in the tail of a spoon or twist of the hook e ...
-
Cannon Mag 20 Dt/Ts - page 19
19 CANNON® LIMITED W ARRANTY Johnson Outdoors Inc. warrants to the original purchaser that if the accompanying product (see exclusions below) proves to be defective in material or workmanship within the following warranty periods, Johnson Outdoors Inc. will, at its option, either repair or replace same without charge (but no cash refunds will be m ...
-
Cannon Mag 20 Dt/Ts - page 20
20 Authorized Service Centers Your new Cannon® Downrigger was built to exacting specifications under rigid quality control to p rovide you years of trouble-fr ee operation. If it should ever need adjustment or serv ice, you may send it to any Cannon® Authorized Service Center near you. For a current list of aut horized Cannon Service Center s, in ...
-
Cannon Mag 20 Dt/Ts - page 21
TM MAG 20 DT/HS 1902200 Form No. 3394903 Rev 12/06 ...
-
Cannon Mag 20 Dt/Ts - page 22
1 3392500 FRAME - LARGE BLACK (LEXAN) 42 0467695 BRAKE PLATE - REEL 83 9430160 >WASHER - STAR 5/16" [3.EA] 2 4427005 NOSE DECAL MAGNUM 43 1264670 CLUTCH PAD 84 2277002 >UNIVERSAL LINE RELEASE 3 9040040 HOOK - 1/4" - 20 ROLLED 44 1433074 GEAR - DRIVER WORM 85 3998600 >UNI-STACKER RELEASE 4 2263102 NUT - HEX 1/4"-20 45 9010003 ...
-
Cannon Mag 20 Dt/Ts - page 23
TM MAG 20 DT/HS/E 1902201 Form No. 3394922 Rev 12/06 ...
-
Cannon Mag 20 Dt/Ts - page 24
1 3392500 FRAME - LARGE BLACK (LEXAN) 42 9250002 PIN - DRIVE SHAFT 3/16" ROLL SS 83 9340101 >SCREW - SET 3/8"-16 x 5/8" [2.EA] 2 4427005 NOSE DECAL MAGNUM 43 0467695 BRAKE PLATE - REEL 84 9430160 >WASHER - STAR 5/16" [3.EA] 3 9040040 HOOK - 1/4" - 20 ROLLED 44 1264670 CLUTCH PAD 85 2277002 >UNIVERSAL LINE RELEASE 4 ...
-
Cannon Mag 20 Dt/Ts - page 25
TM MAG 20 DT/TS 1902205 Form No. 3394908 Rev 12/06 ...
-
Cannon Mag 20 Dt/Ts - page 26
1 3392505 FRAME - LARGE WHITE (LEXAN) 40 1480070 SHAFT - DRIVE 79 9430160 >WASHER - STAR 5/16" 2 4427005 NOSE DECAL MAGNUM 41 9250002 PIN - DRIVE SHAFT 3/16" ROLL SS 80 2200109 >OFFSHORE SALTWATER RELEASE 3 9040040 HOOK - 1/4" - 20 ROLLED 42 0467695 BRAKE PLATE - REEL 81 3992300 SWIVEL HEAD ASSEMBLY 4 2263102 NUT - HEX 1/4" ...
-
Cannon Mag 20 Dt/Ts - page 27
TM MAG 20 DT/TS/E 1902206 Form No. 3394921 Rev 12/06 ...
-
Cannon Mag 20 Dt/Ts - page 28
1 3392505 FRAME - LARGE WHITE (LEXAN) 41 1480070 SHAFT - DRIVE 81 2200109 >OFFSHORE SALTWATER RELEASE 2 4427005 NOSE DECAL MAGNUM 42 9250002 PIN - DRIVE SHAFT 3/16" ROLL SS 82 3992300 SWIVEL HEAD ASSEMBLY 3 9040040 HOOK - 1/4" - 20 ROLLED 43 0467695 BRAKE PLATE - REEL 83 0267001 ► SIDE PLATE (RH) 4 2263102 NUT - HEX 1/4"-20 44 1 ...
¿Tienes una pregunta acerca de Cannon Mag 20 Dt/Ts?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cannon Mag 20 Dt/Ts, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cannon Mag 20 Dt/Ts probablemente compartirá una forma de solucionarlo.