-
CycleOps 400 PRO - page 1
C y cleOps P ro Ser ies Indoor C y cles User Guide 400 P ro 300 P ro 200 P ro 100 P ro Deutsche Anweisungen www .cycl eops.com/user guide Istruzioni italiane www .cycl eops.com/user guide Nederlandse instructies www .cycl eops.com/user guide Norsk instruksjoner www .cycl eops.c om/user guide ...
-
CycleOps 400 PRO - page 2
1 T ABLE OF C ONTENTS CHAPTERS: 1. BEFORE BEGINNING................................................................................1 2. UNP ACKING THE CY CLEOPS PRO SERIES INDOOR CY CLE............2 3. INDOOR CY CLE ASSEMBL Y ....................................................................3 Attach S tabilizer F eet Attach Handlebar Attach Seat ...
-
CycleOps 400 PRO - page 3
2 CHAPTER 2: UnP ACking THE Cy ClEoPs PRo sERiEs indooR Cy ClE Place the box upright and cut the plastic binding str aps. Lif t the top of the box to expose the indoor cycle and packaging. Remove all parts from the box including foam inserts. Ensure all the following parts are included: Name Quantity A Rear stabilizer 1 B F ront stabilizer 1 C Main ...
-
CycleOps 400 PRO - page 4
3 A B 1. Note the differ ence between the front and rear stabilizers. The larger stabiliz er with wheels goes in the rear of the indoor cycle (under the fl y wheel). 3. Attach the front stabiliz er to the front of the main frame with four 5mm stabi- lizer bolts and stabilizer washers using the 5mm Allen wrench. Tight en the inner bolts fi rst, an ...
-
CycleOps 400 PRO - page 5
4 Attach Seat G A seat has been included with the Cy cleOps Pro Series indoor cycle. If desired, the indoor c ycle can accommodate an off-the-shelf seat to personalize the fit, feel and ride. In some instances, a shorter seat post clamp is required for individuals under five f eet tall. If desired , contact Saris Cycling Group to purchase the sho ...
-
CycleOps 400 PRO - page 6
5 1. If necessary , the four outer lev eler feet can be adjusted . T urn stabilizer feet clockwise to lower the indoor cycle. T urn stabilizer feet c ounterclockwise to raise indoor cycle. Leveler F eet Lev el the Indoor C ycle Move the indoor cycle to where it will be used and lev el it by rotating the adjustable feet underneath the stabiliz ers. ...
-
CycleOps 400 PRO - page 7
6 If desired , the CycleOps P ro Series indoor cycle can accommodate any standar d pedals to personalize the fi t, feel and ride. Install using the pedal manufacturer ’ s specifi cations. Improper installation can result in damage to the crank. Damage caused by improper pedal installation is not co vered under warranty . Attach P edals Right pe ...
-
CycleOps 400 PRO - page 8
7 1. Adjust handlebar to maximiz e comfort or duplicate outdoor riding position. Stop the fl ywheel and dismount the in- door cycle before making adjustments. 3. T urn small L handle counterclockwise to loosen. M ove the handlebar f or ward or back to achieve pr oper handlebar position. T urn small L handle clock wise to tighten. 2. T urn large L ...
-
CycleOps 400 PRO - page 9
8 CHAPTER 5: C ommon AdJUsTmEnTs Replace Speed Sensor Battery (200 Pro only) Over time, the lithium batter y in the speed sensor will need to be changed. See Preven tative Maintenance f or when to replace . 1. Using a 4mm Allen wrench, remove the three chain guard bolts and remo ve the chain guard . 3. Replace the battery with a compatible CR2032. ...
-
CycleOps 400 PRO - page 10
9 Replace Hub Batter ies (400 Pro/300 Pr o only) Over time, the batteries that power the electronics in the hub will need to be changed . See Prev entative Maintenance f or when to replace. The C ycleOps P ro Series indoor c ycle uses two AA batteries . The battery cap is split to make this task as easy as possible. 1. Rotate the fl ywheel to acce ...
-
CycleOps 400 PRO - page 11
10 Adjust Fly wheel/Chain T ension Over time and after substantial use, the chain on the CycleOps P ro Series indoor c ycle will stretch. Adjusting the tension/align- ment is a diffi cult task and improper adjustment can lead to prematur e chain/cog wear . I t is recommended this task be done with assistance from an authorized indoor cycle dealer ...
-
CycleOps 400 PRO - page 12
11 1. Back off resistance until it the knob stops turning (counterclockwise). T hen turn clockwise 180 degrees (1/2 turn). 2. Loosen the clamping bolts with a 5mm Allen wrench. Align the brake pad by sliding it towar ds the fl y wheel. Stop when the pad just touches the fl ywheel. Align the arc of the brake pad with the arc of the fl ywheel. 3. ...
-
CycleOps 400 PRO - page 13
12 WEEKL Y In addition to daily maintenance , per form the f ollowing each week: • Inspect and adjust brake pad. • Properly tight en pedals and all hardware attaching toe clips/str aps (if applicable). Tighten pedals to 300 in-lbs. • Inspect handlebar clamp assembly . Tighten clamp bolt if loose . • Inspect seat post clamp and c ...
-
CycleOps 400 PRO - page 14
13 CHAPTER 8: R Adio fREqUEnCy (Rf) inTERfEREnCE Radio frequency (RF) inter ference with other devices ma y cause intermittent loss of information. Wireless Internet access points , microwa ves, cordless phones, or other wireless devices may cause frequency interference. T o mitigate the chance of interference , set wireless access points to the lo ...
-
CycleOps 400 PRO - page 15
14 Saris Cycling Group , Inc. 5253 V erona Road Madison WI 53711 800.783.7257 www .c ycleops.com 19186D 03/11 CHAPTER 10: W ARR AnT y Manufacturer ’ s W arranty (under normal use) Fr ame: Lifetime (Home) Fifteen Y ears (Commercial) Main frame assembly Stabilizers Parts: Three Y ears Excludes w ear items: Brake pads Chain P awls Seat post sleeve H ...
¿Tienes una pregunta acerca de CycleOps 400 PRO?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con CycleOps 400 PRO, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con CycleOps 400 PRO probablemente compartirá una forma de solucionarlo.