-
Niles Audio HDL-6 - page 1
HD L - 6 INSTALLATION & OPERA TION GUIDE MODEL HD L - 6 HIG H D EFI NI TI ON SPEAKER SEL ECT ION SYSTEM HD L - 6 B LENDING T ECHNOLOGY AND A RCHITECTURE ™ ...
-
Niles Audio HDL-6 - page 2
Introduction The HDL-6 allows you to connect up to six pairs of speakers to your stereo receiver or amplifier and play any one pair, any combination of pairs, or all pairs at once. You don't have to worry about overloading your amplifier. The HDL-6 has a protection circuit that keeps your amplifier running safely, even if you have all six pair ...
-
Niles Audio HDL-6 - page 3
Features and Benefits The HDL-6 offers a number of improvements over other speaker selectors: ● High power-handling capability of 250 watt/channel continuous music power. ● Pre-printed room labels are included for easy identification of speaker ON/OFF buttons. ● Rear-panel switch for constant or selectable impedance protection. ● Self-clean ...
-
Niles Audio HDL-6 - page 4
● Removable connectors accommodate up to 14-gauge wire or "pins," making the HDL-6 compatible with most "high-definition" speaker cables. ● 100% tested, electronically and acoustically, for frequency response, distortion, and power handling. ● Standard 17" width allows the HDL-6 to stack neatly with other standard-siz ...
-
Niles Audio HDL-6 - page 5
Installation Considerations HDL-6 Power Handling The HDL-6 is designed for use with a receiver or amplifier having a maximum power output of 250 watts per channel at 8 ohms. Damage caused by the use of a higher-power receiv- er or amplifier will void the warranty. Consult your Niles deal- er, or receiver/amplifier manufacturer, if you are uncertain ...
-
Niles Audio HDL-6 - page 6
The actual impedance load the HDL-6 presents to your receiver or amplifier will vary, depending on how many speaker pairs are playing, and the impedance rating of each speaker. If you have six pairs of 8-ohm speakers playing, the HDL-6 will present a 4.3 ohm impedance load to your receiver/amplifier. With six pairs of 4-ohm speakers playing, the lo ...
-
Niles Audio HDL-6 - page 7
Avoiding Interference Speaker wires can act as an "antenna" for electrical noise. Locating speaker wires too close to a light dimmer or switch may cause the speakers to emit a "buzzing" or "popping" sound. If you must locate the HDL-6 wiring near electrical devices, route the speaker wires several feet away from the el ...
-
Niles Audio HDL-6 - page 8
7 H IGH D EFINITION S PEAKER S ELECTION S YSTEM F igure 1 Using a Tube Amplifier Tube Amplifier Niles HDL-6 ...
-
Niles Audio HDL-6 - page 9
8 H IGH D EFINITION S PEAKER S ELECTION S YSTEM HDL-6 HIGH D EFINIT ION SPEAKER SE LECTION SYSTEM PROTE CTION 123456 NILES SPEAKER 6 L+ L- R- R+ AMPLIFIER L+ L- R- R+ L+ L- R- R+ L+ L- R- R+ L+ L- R- R+ L+ L- R- R+ SPEAKER 5 SPEAKER 4 SPEAKER 3 SPEAKER 2 L+ L- R- R+ SPEAKER 1 CONSTANT PROTECTION ON OFF Nil es Audio Cor poration, Miami, Fl or ida US ...
-
Niles Audio HDL-6 - page 10
Installation 1. Select a convenient mounting location for the HDL-6. 2. Run all the necessary wiring to the HDL-6. Label the wires for future reference. (See Figure 2) . 9 H IGH D EFINITION S PEAKER S ELECTION S YSTEM TUNER 94.9 15 SPEAKER 6 L+ L- R- R+ AMPLIFIER L+ L- R- R+ L+ L- R- R+ L+ L- R- R+ L+ L- R- R+ L+ L- R- R+ SPEAKER 5 SPEAKER 4 SPEAKE ...
-
Niles Audio HDL-6 - page 11
10 H IGH D EFINITION S PEAKER S ELECTION S YSTEM 3. Make the connections to the HDL-6. The amplifier/speaker connectors on the HDL-6 are removable. If you wish, you may remove these connectors to facilitate installation. (See Figure 3) . Strip 3/8" of insulation from the end of each wire. Tightly twist the end of each wire until no frayed ends ...
-
Niles Audio HDL-6 - page 12
Operation You can use the HDL-6 in two ways: play one pair of speakers at a time, or play multiple pairs simultaneously. If you intend to play more than one pair of speakers at the same time, you should become familiar with the operation of the HDL-6's PROTECTION button. Playing One Pair of Speakers At a Time 1. Make sure the amplifier or rece ...
-
Niles Audio HDL-6 - page 13
Playing Two or More Speaker Pairs Simultaneously 1. Make sure the amplifier or receiver power is OFF, and set the volume to minimum. 2. On the right side of the HDL-6's front panel is a button labeled PROTECTION. This button activates the HDL-6's impedance-correction circuitry, which assures that your receiv- er or amplifier will see a sa ...
-
Niles Audio HDL-6 - page 14
13 H IGH D EFINITION S PEAKER S ELECTION S YSTEM 4. Turn on the amplifier or receiver and select a source, such as the tuner or CD player. 5. Slowly turn up the amplifier or receiver volume, and set it to a comfortable (not maximum) listening level. Be careful not to overdrive or "clip" your amplifier. If the sound becomes muddy or distor ...
-
Niles Audio HDL-6 - page 15
14 H IGH D EFINITION S PEAKER S ELECTION S YSTEM Balancing Speaker Volume The volume control on your receiver or amplifier serves as the "master" volume for all speaker pairs connected. The volume level of the speakers may vary from room to room, due primarily to the physical size of the room and also to the size of the speaker and its ef ...
-
Niles Audio HDL-6 - page 16
Niles Audio Corporation 1 2331 S. W . 1 30 Street Miam i , Florida 3 3 1 86 T el: (305) 238-43 73 Fax: (305) 238-0 1 85 ® B LENDING T ECHNOLOGY AND A RCHITECTURE ™ www.nilesaudio.com ©2002 Niles Audio Corporation. All rights reserved. Niles and the Niles logo are registered trademarks of Niles Audio Corporation. Blending Technology and Architec ...
¿Tienes una pregunta acerca de Niles Audio HDL-6?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Niles Audio HDL-6, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Niles Audio HDL-6 probablemente compartirá una forma de solucionarlo.