-
Hunter Fan M0006-01 - page 1
www .HunterF an.com 1.888.830.1326 PA G E 5 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed T able of C ontents PA G E 12 PA G E 15 Maintenanc e & Cleaning T roubleshooting Light Kit ? ? ? PA G E 14 PA G E 4 Mounting Options PA G E 9 PA G E 11 Wiring Canop y Blades Downrod PA G E 1 ...
-
Hunter Fan M0006-01 - page 2
www .HunterF an.com 1.888.830.1326 M0006-01 • 04/14/14 • © Hunter F an Company 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring , use a qualied electrician. Y ou may need a friend to help you . Check box to see fan weight Assess location 30 inches from blade tip to nea ...
-
Hunter Fan M0006-01 - page 3
www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools . 3 M0006-01 • 04/14/14 • © Hunter F an Company ...
-
Hunter Fan M0006-01 - page 4
www .HunterF an.com 1.888.830.1326 If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) . Guide T ouches BOTH Ceiling & Wa ll S I T U A T I O N 1 Guide T ouches W all but NOT Ceiling S I T U A T I O N 2 Y ...
-
Hunter Fan M0006-01 - page 5
www .HunterF an.com 1.888.830.1326 C eiling Bracket OFF F or angled ceilings, point opening toward peak. Refer to warning w .1 on pg. 2 If you are unable to do this, call T echnical Support at 1-888-830-1326. Use wood scr ews (included) when securing to support struc ture with approved electrical outlet box. Drill 9/64” pilot holes in support str ...
-
Hunter Fan M0006-01 - page 6
www .HunterF an.com 1.888.830.1326 6 M0006-01 • 04/14/14 • © Hunter F an Company Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to nex ...
-
Hunter Fan M0006-01 - page 7
www .HunterF an.com 1.888.830.1326 7 M0006-01 • 04/14/14 • © Hunter F an Company KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top o ...
-
Hunter Fan M0006-01 - page 8
www .HunterF an.com 1.888.830.1326 Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canop y sit loosely on top of the fan. 8 M0006-01 • 04/14/14 • © Hunter F an Company ...
-
Hunter Fan M0006-01 - page 9
www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , downrod, and hanging bracket. (Grounding) Green/Y ellow Stripe Green/Y ellow Stripe Wh ...
-
Hunter Fan M0006-01 - page 10
www .HunterF an.com 1.888.830.1326 Canop y Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown. No te: Fan style may vary . Lift the canopy into place so that the screw holes are aligned . Screw Holes Insert the two canopy screws found in the hardwar e bag. 10 M0006-01 • 04/14/14 • © Hunter ...
-
Hunter Fan M0006-01 - page 11
www .HunterF an.com 1.888.830.1326 Blades Align the three holes in the blade with the three blade iron posts. Squeeze the blade and the blade post together . The ared tops of the blade iron posts will be fully visible above the blade when properly assembled . Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repe ...
-
Hunter Fan M0006-01 - page 12
www .HunterF an.com 1.888.830.1326 12 M0006-01 • 04/14/14 • © Hunter F an Company Partially install two of the switch housing screws found in the bag . Connect the plugs from the upper and lower swit ch housings. Make sure to line up the colored markings on the connec tors. Align the notches in the sides of the lower switch housing with the sc ...
-
Hunter Fan M0006-01 - page 13
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! No te: Glass shade styl e and number of lights may vary . See next page for fan opera tion instruc tions. Connect a pull chain pendant to each of the short chains coming from the switch housing . T o install the shade, rst loosen the thumb screws. Raise ...
-
Hunter Fan M0006-01 - page 14
www .HunterF an.com 1.888.830.1326 Maintenanc e & Cleaning ON T urn P ower F or cleaning the fan, use sof t brushes or cloths to prevent scratching . Cleaning products may damage the nishes. T o switch the direc tion of air ow , mov e the reverse switch to the opposite position. Reverse Switch The fan pull chain controls the speed: from h ...
-
Hunter Fan M0006-01 - page 15
www .HunterF an.com 1.888.830.1326 T roubleshooting Exc essive wobbling • Make sure that the blades are properly installed on the blade iron posts. • T urn the power off , support the fan carefully , and check that the hanger ball is properly seated . • Use the provided balancing kit and instruc tions to balance the fan. Noisy Operation • T ...
¿Tienes una pregunta acerca de Hunter Fan M0006-01?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hunter Fan M0006-01, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hunter Fan M0006-01 probablemente compartirá una forma de solucionarlo.