-
Electrolux ELECTRONIC BASIC IH 18 - page 1
Inst ant aneous W ater Heater Instructions for installation and use IH 18 electronic basic IH 21 electronic basic IH 24 electronic basic ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 2
2 Contents Page Important instructions for the user 3 General 3 Operating the appliance 3 T emperature preselection 3 Hot water flowrate 4 Care and maintenance of the appliance 4 Important instructions for the installer 5 General 5 Appliance constitution 5 T echnical data 6 Appliance function 7 Safety temperature limiter 7 Installing the appliance ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 3
3 When the appliance is operated with a thermostatic mixer tap, the temperature setting on the instantaneous water heater must be around 8°C higher than on the thermostatic mixer tap. Recommendation for energy-saving operation: 40°C for washbasin, shower , and bath (knob t angibly engages). 55°C for kitchen sink. If this temperature is no longer ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 4
4 Hot water flowrate Up to the appliance’s max. power limit, the instantaneous water heater supplies the set hot water temperature regardless of the water flowrate selected. If the hot water temperature is not attained when the hot water valve is fully opened, more water flows than can be heated by the appliance power . In this case, the hot wate ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 5
5 Important instructions for the installer General The instantaneous water heater is manufactured and tested in conformity with the valid IEC specifications and DIN standards. The appliance complies with the Appliance Safety Act. The indications given on the rating plate, the technical connection specifications of the electricity and water companie ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 6
6 T echnical dat a *) In addition to the flow pressures of the instantaneous water heater itself, consideration must be given to the pressure losses in the household pipework. Mo del T ype u nven ted No min al c ap acity l 0 ,4 Dim ensio ns W id th He igh t De pth mm 2 26 4 69 9 9 W eig ht k g 3 ,9 No min al o verp res sur e Mp a P r o tec t io n c ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 7
7 Appliance function The fully electronically controlled ELECTROLUX IH instant water heater is a pressurised appliance for the supply of one or more tapping points and heats the water as the latter continuously flows through it. A flowrate sensor switches on the heating at a flowrate of around 3 l/min and off again at around 2,5 l/min. The micropro ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 8
8 Installing the appliance The appliance should only ever be installed or stored in frost-free premises. Dimensioned diagram 1 = Quick fastener for appliance mounting 2 = Wall mounting 3 = Upper connection terminal (factory-set) 3a = Lower connection terminal for electrical connection 4 = Upper cable bushing 4a = Lower cable bushing for electrical ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 9
9 Appliance installation Carefully unpack and take out the enclosed pack. Prep are the appliance for assembly . Hood dismounting Press in the engagement lug on the underside of the appliance from above or from the front with a screwdriver and take off the hood. Pull out the connection lead of the temperature set-point pickup on the electronic syste ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 10
10 W ater connection The water inlet temperature on the cold water connection should be max. 25°C. If plastic pipe systems are used as installation material, the pipe manufacturer must expressly and unreservedly confirm the applicability and quality of his pipes for this application. The ELECTROLUX IH electronic can be operated with all pressure f ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 11
11 Installation versions For fittings directly on the appliance, the bushing openings pre-embossed in the appliance hood must be cut out for the extension pipes of the fitting. The supporting sheet (1) enclosed with the fitting fixes the extension pipes in position and seals the housing openings. T o ensure moisture protection , the supporting shee ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 12
12 − Shut off cold water on shutoff unit (1) − Loosen cap nut (2) using a spanner − T ake out and clean strainer (3) − Re-assemble in reverse sequence − Open cold water on shutoff unit (1); check tightness Cleaning the strainer insert If the water flowrate is reduced by dirt from the cold water line, the strainer- insert should be cleaned ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 13
13 Electrical connection The electrical connection should only ever be made after the water is connected! The appliance is only suitable for a fixed connection of 380 V 3 ~ (three-phase current) . The appliance must be connected to the protective conductor . Important note: The wiring must be arranged so that the appliance can be de-energised (disc ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 14
14 Mains connection underneath (alternative) For this connection version, transpose the mains connection terminal (1) from top to bottom. Note the terminal designation on the back wall, and do not cross the connection leads to the safety temperature limiter . Carry out cable inlet opening (2), inlet bush (3), and bush fixing under the mains connect ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 15
15 T emperature selector range limit ation The maximum temperature able to be set can be limited to 40°C or 45°C. Important! Before dismantling, set the knob to the minimum tempe- rature of 30°C. Detach the temperatur set-point pickup (2) in the appliance hood. Turn the setting dial (3) so that the printed set- point coincides with the hood mark ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 16
16 Using the appliance for the first time and checking The unit must be installed and started up by an approved firm of installers which accepts liability for safety and proper function. Before the appliance is energised (connected to the electricity supply), it should be thoroughly flushed with cold water and the tightness of the screwed joints ch ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 17
17 Check the voltage Clean strainer insert (see page 12) Dismantle and clean the bubblers and showers heads Inspection and repair only by the trained engineer Inspection and repair only by the trained engineer Inspection and repair only by the trained engineer Cause Fault Remedy - Appliance is not live - S trainer insert is clogged - Soiling or sca ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 18
18 Fault indications - L1 o r L3 p h a se mi s s ing - L2 p h a se mi s s ing *) The in divi d u al fa u lt ar e i nd ica t ed e v e ry 5 se c. Th e i nd i c atio n m o de s t ar ts a fre s h e ver y 4 0 s e c . Impo r t ant! If the fault has b een recti fied , t he fau l t me mory goes a utomat i- cally in Res e t - Funct ion.( S ometim es with co ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 19
19 Important for the expert The electronic controls the safety-function of the appliance. When a fault is noticed, the fault indicator (LED) blinks and the heating element is switched off. After the fault has been recitified, fault memory will be automatically cancelled Instructions for the fault finding see in "Instructions for installation a ...
-
Electrolux ELECTRONIC BASIC IH 18 - page 20
Customer service If your appliance has a fault, please contact your customer service centre for advice. Electric appliances should only ever be repaired by a trained electrician, since the user may be seriously endangered by improper repairs. A list of the addresses of customer service centres is attached. If your appliance requires service, you wi ...
¿Tienes una pregunta acerca de Electrolux ELECTRONIC BASIC IH 18?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Electrolux ELECTRONIC BASIC IH 18, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Electrolux ELECTRONIC BASIC IH 18 probablemente compartirá una forma de solucionarlo.