-
Harbor Freight Tools 95619 - page 1
4HP Gas Pressure W asher ASSEMBL Y AND OPERA TING INSTRUCTIONS 95619 Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website ...
-
Harbor Freight Tools 95619 - page 2
SKU 95619 F or technical questions please call 1-800-444-3353 P age 2 Specifications Gas Engine 4HP OHC Mitsubishi Engine, 3600 RPM, Recoil Start, Uses Unleaded Fuel, 20 Oz. Engine Oil Capacity , 6.25 Gal. Fuel Capacity (2.5L). Environmental Approved by E.P .A. (Environmental Protection Agency) Pressure W asher 2200 PSI Rated, Cast Iron Cylinder S ...
-
Harbor Freight Tools 95619 - page 3
SKU 95619 F or technical questions please call 1-800-444-3353 P age 3 4. Burn Hazard. The engine and high pressure pump become hot during operation. Do not touch the engine or pump until they have cooled down after use. Keep work area clean 5. . Cluttered areas invite injuries. Observe work area conditions 6. . Do not use machines or power tools in ...
-
Harbor Freight Tools 95619 - page 4
SKU 95619 F or technical questions please call 1-800-444-3353 P age 4 Check for damaged parts 19. . Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting xtures; an ...
-
Harbor Freight Tools 95619 - page 5
SKU 95619 F or technical questions please call 1-800-444-3353 P age 5 Clean up fuel spills immediately . 32. Dispose of uids and cleaning materials in ac - cordance with local, state or federal regulations. Store oily rags in a metal container . Store gasoline in a well ventilated, secure locker . Do not smoke and do not allow re ame or el ...
-
Harbor Freight Tools 95619 - page 6
SKU 95619 F or technical questions please call 1-800-444-3353 P age 6 Unpacking When unpacking, chec k to make sure the parts shown in the photo below and in the diagrams on pages 13 and 14 are included. If any parts are missing or broken, please call Harbor F reight T ools at the number on the cov er of this manual. 07d, 08b Spray Gun High Pressur ...
-
Harbor Freight Tools 95619 - page 7
SKU 95619 F or technical questions please call 1-800-444-3353 P age 7 Assembl y NO TE: Please refer to the photo belo w and the table and diag ram on pages 13 and 14 when reading this section and assembling y our pressure washer . 1. Attach the Car t Handle (16) to the Car t Fr ame (5) as shown in the photo below . Secure in place using the Handle ...
-
Harbor Freight Tools 95619 - page 8
SKU 95619 F or technical questions please call 1-800-444-3353 P age 8 07d Using Detergent CAUTION! T o avoid injury , ONL Y run pressure washer detergent through the Detergent Suction Hose (40). Detergent Suction Hose (40) Figure A 1. Press the supplied Detergent Suction Hose (40) onto the tting on top of the pump. Place the other end of the hos ...
-
Harbor Freight Tools 95619 - page 9
SKU 95619 F or technical questions please call 1-800-444-3353 P age 9 Important Guidelines for W ater Supply 1. Do not leave engine running without spra ying water . If engine is left running for more than three (3) minutes without discharging w ater , e xcess pressure can cause damage to the pump seals and / or high pressure hose. 2. The water sup ...
-
Harbor Freight Tools 95619 - page 10
SKU 95619 F or technical questions please call 1-800-444-3353 P age 10 Operation Pick up the Spray Gun (37) and point it in a safe direction. Squeeze the Spray Gun 1. T rigger until all internal air is released, and a steady ow of water comes out. Then release the Spray T rigger . 2. T urn the Fuel V alve (D) to the open position (see engine pho ...
-
Harbor Freight Tools 95619 - page 11
SKU 95619 F or technical questions please call 1-800-444-3353 P age 11 Operation (Continued) T urning Off the Pressure W asher 1. T ur n t he Sp e ed Co nt ro l L ev e r (C ) to th e r ig ht , o r s to p po si t io n . Th e en g in e w il l stop. 2. T ur n the Fuel V alve (D) up to the left, or closed position (see photo page 9). 3. T ur n off the ...
-
Harbor Freight Tools 95619 - page 12
SKU 95619 F or technical questions please call 1-800-444-3353 P age 12 Cleaning Suggestions Hold the Spra y Gun (37) at about a 45° angle and steadily s weep the stream back and f or th. Do not point the spray directly at the surf ace to be cleaned. If a head-on angle is used, dir t may embedded in the surf ace being cleaned. F ollow a steady , co ...
-
Harbor Freight Tools 95619 - page 13
SKU 95619 F or technical questions please call 1-800-444-3353 P age 13 PUMP MAINTENANCE CHART* Maintenance T ype Before Use After Use Hours of operation After Initial 50 hr . Break-in Period Weekly / 10 hr . 100 hr . 150 hr . 200 hr . Inspect tool for damage X Wipe off with clean, moist cloth X X X Clean Filters, Check for Pump Oil and W ater Leaks ...
-
Harbor Freight Tools 95619 - page 14
SKU 95619 F or technical questions please call 1-800-444-3353 P age 14 NO TE : Some par ts are listed and shown f or illustration pur poses only and are not av ailable individually as replacement parts. Assembl y Drawing ...
-
Harbor Freight Tools 95619 - page 15
SKU 95619 F or technical questions please call 1-800-444-3353 P age 15 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIBUTOR HAS PRO VIDED THE P AR TS DIAGRAM IN THIS MANU AL AS A REFERENCE TOOL ONL Y . NEITHER THE MANUF ACTURER NOR DISTRIBUTOR MAKES ANY REPRESENT A TION OR W ARRANTY OF ANY KIND TO THE BUYER THA T HE OR SHE IS ...
-
Harbor Freight Tools 95619 - page 16
SKU 95619 F or technical questions please call 1-800-444-3353 P age 16 LIMITED 1 YEAR W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year fro ...
¿Tienes una pregunta acerca de Harbor Freight Tools 95619?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Harbor Freight Tools 95619, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Harbor Freight Tools 95619 probablemente compartirá una forma de solucionarlo.