-
Sharp MX-2314N - page 1
INST ALLA TION MANUAL Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these p arts with specified ones for maintaining the safety a nd performance of the set. SHARP CORPORA TION This document has been published to be u sed for after sales service only. The contents are subject to change withou ...
-
Sharp MX-2314N - page 2
MX-31 14N T ransit, Installation (using) environment, Note - i MX-31 14N 6HUYLFH0D QXDO T ransit, Installation (using) environment, Note 1. Inst alling (use) conditions Before installing the machine, check that th e following installing (use) conditions are satisfied. If the installing (use) conditions are not satisfied, the machine may not ...
-
Sharp MX-2314N - page 3
MX-31 14N T ransit, Installation (using) environment , Note - ii Operational environment T emperature: 10 to 35 q C Humidity: 20 to 85% RH Atmospheric pressure: 590 to 1013h Pa (altitude: 0 to 2000 m) (2) Cont aminates If dust enters the machine, it may cause dirty copy and a paper jam, resulting in a shortened lifetime. (3) Direct sunlight If t he ...
-
Sharp MX-2314N - page 4
MX-31 14N Transit, Inst allation (using) environment, Note - iii G . Note for proper dr um, developi ng, fusing and transfer unit han dling When handling the OPC drum, developing and transfer units, observe the following items. Drum unit • T o prevent damage to the OPC drum, avoid working on the drum unit in high intensity light areas. • When t ...
-
Sharp MX-2314N - page 5
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 1 MX-31 14N 6HUYLFH0DQXDO [2] MX-2314N/2614N/31 14N (MAIN UNIT) 1. Unp acking A. Unpacking B. Fixing tape and protection m aterial removal 26cpm/31cpm machine C. Packed items check * Depending on th e country D. Lock release (1) T ray rotation plate lock release 1) Pull out the tray . Turn t ...
-
Sharp MX-2314N - page 6
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 2 2. Inst allation When an option al paper feed desk is connected to the machine, unpack and install the paper feed desk, then unpack the machine. Place the machine on the option desk securely , and perform the installing procedures of the machine. Place the machine on the optional desk f irmly and ...
-
Sharp MX-2314N - page 7
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 3 6) Attach the cover . 7) Shake the developing unit several times horizontally and strongly . 8) Open the toner shutter of the developing u nit and check to confirm that the re is pr oper amount of developer . If not, per- form procedure 6) again. • Check that there is proper amount of developer ...
-
Sharp MX-2314N - page 8
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 4 When installing the machine, there is no need to remove or install the OPC drum u nit. If it must b e removed or installed for any reaso n, follow the procedures bel ow . When remov ing or installing the OPC drum unit, put your hand from below the unit and slide it in parallel along the guide on ...
-
Sharp MX-2314N - page 9
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 5 9) Open the front cabinet, and insert each toner cartridge. Be sure to install the co lor cartridges to their proper positions. Avoid installation to a dif ferent color position. Do not forcibly insert the toner ca rtridge. Push it in until the cartridge is secur ely locked in place. Developing u ...
-
Sharp MX-2314N - page 10
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 6 4) Move the PTC cleaning rod back and forth a f ew times to clean the PTC wire. After completion of cleaning, insert the cleaning rod completely to the bottom. 5) Return the LSU cleaning rod to the front cabinet so that the felt faces upward. Fit the boss, and fix it with three pawls. 6) Close th ...
-
Sharp MX-2314N - page 11
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 7 E. Specifi cations setup Use simulation 26-6 to set the machines de stination. After completion of destination settings, change the set valu es to customize the following settings. 3. Image quality check A. Execution ite ms Execute the following items. *1: When a printer option is installed, be s ...
-
Sharp MX-2314N - page 12
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 8 2) Press [EXECUTE] key . [EXECUTE] key is highlighted and the image registration auto- matic adjustment is started. (It takes about 15 sec to co mplete the adjustment.) 3) When the adjustment is completed, [EXECUTE] key returns to the nor mal disp lay , and the value of the adjustment result is d ...
-
Sharp MX-2314N - page 13
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 9 5) If the display of ALL_ROT A TE is N G , turn all the LSU skew adjustment screws to adjust, an d perform the procedures 2) to 4). Repeat the procedur es 2) to 5) until the display of ALL_ROT A TE becomes OK. If the displa y o f ALL_ROT A TE is OK, go to the procedure 6). For the adjustment, rem ...
-
Sharp MX-2314N - page 14
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 10 a. Color copy check items (Check to confirm the following:) Color copy check items Adjustment items 1 There are 12 void areas. Main machine S/ M ADJ3-A to D Sim50-28 2 Registrations (one point for the main scanning, and one point for the sub scanning) are not shifted. Main machine S/ M ADJ4-A Si ...
-
Sharp MX-2314N - page 15
MX-31 14N MX-2314N/2614N/31 14N (MAIN UNIT) 2 – 1 1 b. Monochrome copy check items ( Check to confirm the follo wing:) Color copy check items Adjustment items 1 There are 12 void areas. Main machine S/M ADJ3-A to D Sim50-28 2 The resolution of 5.0 (5 points) can be seen. Main machine S/M Check the dirtof the OC glass Clean the OC glassClean the m ...
-
Sharp MX-2314N - page 16
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 12 Method 2 Use SIM46- 21 to print the colo r balan ce adjust ment sheet, and check each process (CMY) black patch co lor balance and the black patch in order to confirm that the color balance adjustment is proper . If the color balance of each patch of the process black (CMY mixed color) is slight ...
-
Sharp MX-2314N - page 17
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 13 (4) Copy/Printer color balance and density adjustment (Automatic adjustment) When a printer option is installed, be sure to execute the above item. 1) Enter the SIM46-74 mode. 2) Press [EXECUTE] key . The high d ensity process control is performed, and the copy color patch image (adjustment patt ...
-
Sharp MX-2314N - page 18
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 14 6) Set the color patch image (adjustment pattern) printed in the procedure 5) on the document table. Set the color patch image (adjustment pattern) printe d in the procedure 2) on the document table. Place the color patch image so that the fine lines are on the left side. At that time, place 5 s ...
-
Sharp MX-2314N - page 19
MX-31 14N MX-2314N/2614N/31 14N (MAIN U NIT) 2 – 15 10) When "COMPLETED THIS PROCEDURE" is displayed, the adjustment operation is completed. Cancel SIM46-74. The adjustmen t result becomes valid only when the both adjustments in the copy mode and in the pri nter mode are completed. For example, if the copy color balance adjustment (auto ...
¿Tienes una pregunta acerca de Sharp MX-2314N?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sharp MX-2314N, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sharp MX-2314N probablemente compartirá una forma de solucionarlo.