-
Fluke TiR1 - page 1
PN 28030 44 August 2 007 © 2007 Fluke C orporatio n, All rights res erved. P rinted in U SA All produc t names are trad emarks of their resp ective c ompanies. Ti 1 0 , Ti 2 5 , Ti R a n d Ti R 1 Thermal Imagers Users Manual ...
-
Fluke TiR1 - page 2
LIMITED WARRANTY AND LIMI TATION OF LIABILITY Each Fluk e produc t is w arranted to be f ree from defects in materi al and wor kmanshi p under normal use and se rvice. The warr anty peri od is two y ears and begins on the d ate of sh ipment. Part s, produc t repairs, and servi ces are wa rranted for 90 days. T his warran ty extends only to the ori ...
-
Fluke TiR1 - page 3
i Table of Contents Title Page Introduction ............................................................................... 1 Contacting Fluke ....................................................................... 1 Safety Inform ation ..................................................................... 2 Unpacking the Imag er ................... ...
-
Fluke TiR1 - page 4
Ti10, Ti25, TiR and TiR1 Users Man ual ii Changing the SD Card ............................................................... 15 Setting the Backlight .................................................................. 15 General Specifications ............................................................... 15 Detailed Specifications .............. ...
-
Fluke TiR1 - page 5
iii List of Tables Table Title Page 1. Symbols ..................................................................................... 2 2. Features and Cont rols ................................................................ 4 List of Figures Figure Title Page 1. Range an d Span Settings ........................................................... ...
-
Fluke TiR1 - page 6
Ti10, Ti25, TiR and TiR1 Users Man ual iv ...
-
Fluke TiR1 - page 7
1 Introduction The Fluke Ti10, Ti25, TiR, a nd TiR1 Thermal Imagers (hereafter “the Imager”) are handheld im aging cameras used for predictive maintenance, equipment troubleshooting, a nd verification. All four Imagers pr oduce thermal and visual images on a 640 X 48 0 disp lay. Thermal and visual im ages are displayed on the Imager LCD and can ...
-
Fluke TiR1 - page 8
Ti10, Ti25, TiR and TiR1 Users Man ual 2 Safety Informatio n Use the Imager only as specified in this manual. See Table 1 for a list of symbol s used on t he Imager and i n this manu al. A Warn ing identifies haz ardous co nditions an d actions that could c ause bodily harm or death. A Cautio n identifies conditions and actions that could da mage t ...
-
Fluke TiR1 - page 9
Thermal Imagers Unpackin g the Imager 3 Unpacking the Imager Carefully unpack the follo wing items: • Ti1 0, Ti 2 5 , TiR or Ti R1 Im age r • AC Power Adapter/ Charger • Rugged Carr ying Case • SD Memory Card • SD Card Reader • Soft Trans port Bag • User Manual s (in vari ous languag es) • SmartView™ Software • Warranty Regist r ...
-
Fluke TiR1 - page 10
Ti10, Ti25, TiR and TiR1 Users Man ual 4 Table 2. Features and Controls 8 1 4 5 6 9 2 7 3 10 11 12 14 13 exj01.eps Item Description 1 LCD Display 2 Function Soft keys (F1. F2, and F3) 3 Battery Cover 4 Speaker 5 Microphone 6 Auto back light sensor 7 Hand strap 8 AC adapter/c harger input t erminal ...
-
Fluke TiR1 - page 11
Thermal Imagers Using the Menu 5 Table 2. Features and Controls (cont.) Item Description 9 SD memory card compartm ent 10 Retractabl e Lens Co ver 11 Visual camera 12 Thermal (IR) camera 13 Focus control 14 Trigger Using the Menu The menus, cou pled with the three softkeys ( c , a , an d d ), provide access f o r setting features (date, tim e, lang ...
-
Fluke TiR1 - page 12
Ti10, Ti25, TiR and TiR1 Users Man ual 6 Setting the Da te To set the date: 1. Press a until Date appears over the F1 s oftkey. 2. Press the softke y labeled Date . The date can be dis played i n one of two f ormats: MM/DD/Y Y or DD/MM/YY . 3. Press the softkey labe led with the desired da te for mat. 4. Press the softke y labeled Up ( c ) or Down ...
-
Fluke TiR1 - page 13
Thermal Imagers Saving Imager Data 7 Note Minimum f ocus distance for thermal ( IR) camera is 15 cm ( approx. 6 inches). M inimum focus distance for visible ( visual) light camera is 46 cm (approx. 18 inches). Note The Imager can save the image as a simpl e picture or as a radiometr ic image that al lows fur ther temper ature analysi s. To change t ...
-
Fluke TiR1 - page 14
Ti10, Ti25, TiR and TiR1 Users Man ual 8 Selecting a Palette The palette menu provides dif ferent thermal viewing patterns. Gra yscale, Blue- Red, High Contras t, and Ironbow are available in all four Imagers. The TiR1 and Ti25 add Amber and Hot Metal to the list. T o select a palette: 1. Press a until Pale tte appears over c . 2. Press the softke ...
-
Fluke TiR1 - page 15
Thermal Imagers Adjusting the Thermal Image 9 T otal Imager Range Span Le v el exj02.eps Figure 1. Range and Sp an Settings Setting the Level (Man ual) When put into manual ran gi ng, the level setting adjusts the t hermal span within the total temperature range of the I mager. See Figure 1. To set the level: 1. After entering th e manual range mod ...
-
Fluke TiR1 - page 16
Ti10, Ti25, TiR and TiR1 Users Man ual 10 2. Press the softke y labeled Increase to widen the temperature span or Decrease to narro w it. 3. Press the softke y labeled Done to set the Imager’s range le v el. Switching Between PIP and Ful l IR (Ti10 and TiR Only) The Imager can be s et to display a full in frared im a ge (Full IR) or an infrared i ...
-
Fluke TiR1 - page 17
Thermal Imagers Adding Voice An notation to S aved Data (Ti25 and TiR1 Onl y ) 11 4. Press the softke y labeled Up to display the previous image or Down to display the next stored im a ge. To delete a single Im age fro m the SD card: 1. Perform the steps un der viewing stored im ages above to bring the desired image to the displa y. 2. Press the so ...
-
Fluke TiR1 - page 18
Ti10, Ti25, TiR and TiR1 Users Man ual 12 Listening to Voic e Annot ations (Ti 25 and TiR1 Only) To play the voice ann otation already st ored wi th an image on the SD card: 1. Perform the steps in the “Review ing and Deleting Stored Imag es” section to bring th e desired image to the Imager’s dis play. 2. Press the softke y labeled Select . ...
-
Fluke TiR1 - page 19
Thermal Imagers Setting Emiss ivity (Ti2 5 and TiR1 onl y) 13 the object's surf ace. T he Imager detects th e infrared energy from an object and uses this information to estima te the temperature of the object. Most of the objects measu red such as painted m etal, wood, w a ter, skin , and cloth are ve ry efficient at radiating en ergy and it ...
-
Fluke TiR1 - page 20
Ti10, Ti25, TiR and TiR1 Users Man ual 14 To set the emissivit y value directly: 1. Press the softke y labeled ε . 2. Press the softke y labeled Up or Down to increment or decrement respectively the emissivity value dis played just above the softkey labels . 3. Press the softke y labeled Done to select the set value. Setting File Format Data store ...
-
Fluke TiR1 - page 21
Thermal Imagers Changing t he SD Card 15 Changing the SD Card To eject an SD card from the Imager, press in on the exposed edge of th e SD card and then release. T he card should pop partia lly out after releasin g it. Careful ly pull the card ou t of the s lot. Note The SD Card can be inserted and removed whil e the Imager is in operation. To inse ...
-
Fluke TiR1 - page 22
Ti10, Ti25, TiR and TiR1 Users Man ual 16 Software ................................................................Smart V iew™ full analysi s and reporting soft ware included Power Battery ...............................................................Rec hargeable ba ttery pac k (i ncluded) Battery Life ......................................... ...
-
Fluke TiR1 - page 23
Thermal Imagers Detailed Specific ations 17 Detailed Specifica tions Temperature Measurements Temperature Range (not cali brated below -10 ° C) TiR and Ti R1 ................................................. -20 ° C to +100 ° C Ti10 ............................................................... -20 ° C to +250 ° C Ti25 ....................... ...
-
Fluke TiR1 - page 24
Ti10, Ti25, TiR and TiR1 Users Man ual 18 Ti10 ............................................................5 ° C Ti25, TiR, and TiR1 .................................... 2. 5 ° C Minimum span (in auto mode) Ti10 ............................................................10 ° C Ti25, TiR, and TiR1 .................................... 5 ° C IR-F ...
¿Tienes una pregunta acerca de Fluke TiR1?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Fluke TiR1, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Fluke TiR1 probablemente compartirá una forma de solucionarlo.