-
Life Fitness 8225 - page 1
8225 BICEP/TRICEP MACHINE Part # 6845001 Revision:11/2/99 1 ASSEMBLY INSTRUCTIONS ...
-
Life Fitness 8225 - page 2
IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the LIFE FITNESS 8225 BICEP/TRICEP MACHINE. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. 2 NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE ...
-
Life Fitness 8225 - page 3
3 PARTS LIST PART # 6846003 6845503 6845103 6777703 6845303 6845703 6847002 6489902 6851401 6851501 6851901 6852001 3116101 6791102 6782301 6852301 6852601 3102917 3102953 3102901 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 QTY 1 1 1 1 1 1 1 2 1 1 1 1 7 1 2 1 1 10 2 7 KE Y 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 PART # 3 ...
-
Life Fitness 8225 - page 4
STEP 1: FIGURE 1 • LOOSELY assemble the BASE (1) to the TOWER (3) using two 1/2 X 4 ” BOLTS (18), two 1/2 ” WASHERS (24), and two 1/2 ” LOCK NUTS (26) as shown in FIGURE 1. 3 24 26 18 1/2 X 4 ” 1 4 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 ...
-
Life Fitness 8225 - page 5
• LOOSELY assemble the UPRIGHT (5) to the BASE (1) using four 1/2 X 4 ” BOLTS (18), two 1/2 ” WASHERS (24), and four 1/2 ” LOCK NUTS (26) as shown in FIGURE 2. STEP 2: FIGURE 2 • SECURELY assemble three 4-1/2 ” PULLEYS (13) to the TOP BOOM (2) using three 3/8 X 2-3/4 ” BOLTS (22), six 3/8 ” FLANGE SPACERS (28), and three 3/8 ” LOC ...
-
Life Fitness 8225 - page 6
• LOOSELY assemble the TOP BOOM (2) to the TOWER (3) and the UPRIGHT (5) using four 1/2 X 4 ” BOLTS (18), four 1/2 ” WASHERS (24), and three 1/2 ” LOCK NUTS (26) as shown in FIGURE 4. STEP 4 FIGURE 4 • SECURELY assemble SEAT SUPPORT (6) to the BASE (1) using two 1/2 X 2-3/4 ” BOLTS (19), two 1/2 ” WASHERS (24), and two 1/2 ” LOCK NU ...
-
Life Fitness 8225 - page 7
STEP 6: FIGURE 6 7 STEP 7: FIGURE 7 25 16 • SECURELY assemble SEAT PAD (16) to the PAD SUPPORT (7) using two 3/8 X 1- 1/4 ” BOLTS (21) and two 3/8 ” WASHERS (25) as shown in FIGURE 6. • Pull back on SPRING PIN and slide PAD SUPPORT (7) over square tube on SEAT SUPPORT (6) as shown in FIGURE 7. • SECURELY assemble the 3/8 ” SPRING PIN (2 ...
-
Life Fitness 8225 - page 8
8 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 8: FIGURE 8 STEP 9: FIGURE 9 • Snap two WEIGHT PLATE BUSHINGS (37) into the top of all fifteen WEIGHT PLATES (35) as shown in FIGURE 9. 37 35 • SECURELY assemble ARM PAD (17) to the BASE (1) using four 3/8 X 1-1/4 ” BOLTS (20) and four 3/8 ” WASHERS (25) as shown in FIGURE 8. 3/8 X 1-1/4 ” 20 1 ...
-
Life Fitness 8225 - page 9
• Insert the two GUIDE RODS (15) into the base of the TOWER (3) as shown in FIGURE 10. Lubricate the GUIDE RODS (15) with a slicon or teflon spray that is available at most hardware stores. STEP 10 • Slide two WEIGHT STACK CUSHIONS (36) down over the GUIDE RODS (15). See FIG- URE 10. • Using EXTREME CARE slide fifteen WEIGHT PLATES (35) down ...
-
Life Fitness 8225 - page 10
STEP 11: FIGURE 11 • Place TOWER BRACE (4) over the GUIDE RODS (15) as shown and SECURE LY assemble TOWER BRACE (4) to the TOWER (3) using two 1/2 X 4 ” BOLTS (18), two 1/2 ” W ASHERS (24), and two 1/2 ” LOCK NUTS (26) as shown in FIGURE 11. 10 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • LOOSELY assemble two 2 X 7-1/4 ” PLATES (8) to two 4-1 ...
-
Life Fitness 8225 - page 11
• Route threaded end of the TRICEP CABLE (12) around pulleys in TOP BOOM (2) and PULLEY BLOCK ASSEMB LY . Route TRICEP CABLE (12) down through hole in TOWER BRACE (7) as shown in FIGURE 13. STEP 13: FIGURE 13 • SECURELY assemble one 4-1/2 ” PULLEY (13) between the plates of the TOP BOOM (2) using one 3/8 X 2-1/4 ” BOLT (21) and one 3/8 ” ...
-
Life Fitness 8225 - page 12
12 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Screw the treaded end of the TRICEP CABLE (12) approximately 1 ” into the end of theWEIGHT STACK SHAFT (32) of the HEAD PL A TE (33) and tighten jam nut securely. See FIGURE 15. STEP 15: FIGURE 15 33 32 12 ...
-
Life Fitness 8225 - page 13
13 • Route the threaded end of the ARM CURL CABLE (11) through the UPRIGHT (5) as shown, then SE- CURE LY assemble one 4-1/2 ” PULLEY (13) to the UPRIGHT (4) and over the top of the cable using two 3/8 X 2-3/4 ” BOLTS (22), two 3/8 ” FLANGE S PACERS (28), two 3/8 ” W ASHERS (25), and two 3/8 ” LOCKNUTS (27). (NOTE: The LOW ROW CABLE (11 ...
-
Life Fitness 8225 - page 14
14 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 17: FIGURE 17 • Screw the threaded end of the ARM CURL CABLE (11) into threaded housing on the base of BASE (1) and tighten jam nut securely. 1 11 3 14 • Slide the SHROUD (14) between the TOWER (3) as shown in FIGURE 17. • SECURELY tighten the bolts of the PULLEY BLOCK ASSEMBLY. ...
-
Life Fitness 8225 - page 15
15 STEP 18: FIGURE 18 • SECURE LY assemble the SHROUD (14) to the TOWER (63) using four 3/8 X 1 ” BUTTON HEAD CAP SCREWS (23) as shown in FIGURE 18. 3/8 X 1 ” BUTTON HEAD CAP SCREW 23 3 ...
-
Life Fitness 8225 - page 16
16 FIGURE 19 • Attach ARM CURL BAR (9) & TRICEP ROPE (10) to ball ends of cables using two 5/16 ” SNAP HOOKS (30). See FIGURE 19. • If the HEAD PL ATE (33) does not sit on top of the first WEIGHT PL ATE (35), push the head plate down, insert the SELECTOR PIN (34) and perform several repetitions on the machine. This will relax the cable sy ...
¿Tienes una pregunta acerca de Life Fitness 8225?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Life Fitness 8225, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Life Fitness 8225 probablemente compartirá una forma de solucionarlo.