-
Sanyo VCB-3424 - page 1
INSTRUCTION MANUAL VCB-3424 B/W CCD Camera About this manual B efo re in st a ll in g a nd us in g th e ca m e ra, pl ea se re ad th is ma nu al carefully. Be sure to keep it handy for later reference. L73T 4/ U S G B 19 99 , 8, 3 ...
-
Sanyo VCB-3424 - page 2
SANYO INDUSTRIAL VIDEO B/W VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty . The names and addresses of Authorized Sanyo Service Centers may be obtained ...
-
Sanyo VCB-3424 - page 3
Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. CONTENTS INFORMATION TO USER .................................................................... 2 PRECAUTIONS ........................... ...
-
Sanyo VCB-3424 - page 4
Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This installation should be made by a qualified service person and should conform to all local codes. ...
-
Sanyo VCB-3424 - page 5
PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For ...
-
Sanyo VCB-3424 - page 6
PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 2 Line phase adjustment volume (LINE PHASE) When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning this volume. 3 Pow ...
-
Sanyo VCB-3424 - page 7
PARTS NAMES 7 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 8 Flange-back adjustment screw (FLANGE BACK ADJ.) 9 Flange-back lock screw (FLANGE BACK LOCK) F Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixin ...
-
Sanyo VCB-3424 - page 8
PARTS NAMES Concerning auto-iris lenses DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.) VIDEO type auto-iris lens A lens with amplifier circuit that operates ...
-
Sanyo VCB-3424 - page 9
MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “ L ” is more than 7 mm. If not, that may damage the camera and prevent proper installation. 1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens. CS mount type lens Carefully align the lens mount wit ...
-
Sanyo VCB-3424 - page 10
MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. Cut the cab le at t he pl ug, the n remove ap prox. 8 mm of the cable s h eath an d str ip ab out 2 m m from eac h wire. 2 Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then cl ...
-
Sanyo VCB-3424 - page 11
CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Connect to 24 V AC UL listed class 2 power supply. CAUTION: • To prevent camera and/or power supply failure, pay close ...
-
Sanyo VCB-3424 - page 12
SETTINGS Camera setup section Control name Position a Mirror image switch (MIR) OFF b Backlight compensation switch (BLC) OFF c Electronic iris (EI) OFF d Auto-iris lens switch (A.I. LENS) (see page 6) DC e Lens iris level volume (LEVEL) about centre Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the s ...
-
Sanyo VCB-3424 - page 13
SETT INGS Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL (VR401) volume when shooting in the conditions described below. L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast • If shooting simultaneously in a dark room and through a bright window. • If the subject backgrou ...
-
Sanyo VCB-3424 - page 14
SETTINGS Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below. Switch the display on the monitor from camera 1 to camera 2. Adjust the LINE PHASE volume on camera 2 until the vertical roll of the image stops. I ...
-
Sanyo VCB-3424 - page 15
SPECIFICATIONS Scanning system : EIA standard (525 TV lines, 30 frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/3 i nc h s olid s ta te i ma ge de vi ce CC D Picture elements : 542 (H) x 492 (V) Effective picture elements : 512 (H) x 492 (V) Synchronizing system : Line lock Resolution : 400 TV lines horizontally, 350 TV lines vertically ...
¿Tienes una pregunta acerca de Sanyo VCB-3424?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sanyo VCB-3424, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sanyo VCB-3424 probablemente compartirá una forma de solucionarlo.