Español dropdown-ico

Manual de instrucciones Sears 113.226424

24 de páginas 2.81 mb
Descargar

Pasar a la página of 24

Summary
  • Sears 113.226424 - page 1

    SAVE THIS MANUAL FOR FUTURE REFERENCE BELT AN D DISC SANDER Serial Numbe[ Model and serial number may be found on the back side of the base. You should record both model and serial number in a safe place for future use. CAUTION: Read GENERAL and ADDITIONAL SAFETY INSTRUCTIONS _arefuily ! BELT A SANDE DISC o assembly • operating • repair parts S ...

  • Sears 113.226424 - page 2

    i i i ii•i i iiii SEARS, ROEBUCK AND CO:, 698t731A. Sears Tower. Chicago, IL 60684 general safety instructions for power tools 1. KNOW YOUR POWER TOOL Read and understand the owner's manual and labels affixed to the toot. Learn its application and limitations as welt as the specific potential hazards peculiar to this tool. 2. GROUND ALL TOOL ...

  • Sears 113.226424 - page 3

    additionaU safety disc sander instructions for bett and - Safety is a combination of operator common sense and alertness at aft times when the sander is being used. WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT TO OPERATE YOUR BELT AND DISC SANDER UNTIL IT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUC- TIONS .... AND UNTIL YOU HAVE ...

  • Sears 113.226424 - page 4

    S 12_ Think Safety _ ::_: Safety is a combination of operator common sense and alterness at all times when the sander is in operation. WEAR YOUR The operation of any power tool can result in for- eign objects being thrown into the eyes, which can result in severe eye darnage. Always wear safety goggles (not glasses)complying with ANSI Z87.1 (shown ...

  • Sears 113.226424 - page 5

    cations and electricaJ This machine is designed to use, and is equip- ped with, a 3450 RPM motor, it is wired for opera- tion on 110-120 volts, 60 Hz., alternating current. (TOOL MUST NOT BE CONVERTED TO OPER- ATE ON 230 VOLT). For replacement motor refer to parts list in this manual. CONNECTING TO POWER SUPPLY OUTLET This machine must be grounded ...

  • Sears 113.226424 - page 6

    IOTOF ELECTRICAL REQUIREM E UNPACKING AND CHECKING ASSEMBLY Mounting Belt and Disc Sander N ......... : 2 ........ _5 MTENTS . :::... 6 To Workbench ............................... 7 Clamping Belt And Disc Sander To Workbench ............................... 7 installing Timing Belt .......................... 8 installing Pulley Cover .............. ...

  • Sears 113.226424 - page 7

    assembly MOUNTING BELT AND DISC SANDER TO WORKBENCH If belt and disc sander is to be used in a perma- nent location, it should be fastened securely to a firm supporting surface such as a workbench. If mounting to a workbench, holes should be drilied through supporting surface of the work- bench using dimensions illustrated. ° . Each leg should be ...

  • Sears 113.226424 - page 8

    ]u Irl 1 2, Place right hand under motor pulley and lift pulley and belt upward. Using left hand, place belt onto top pulley. i i i 3, The motor is spring loaded so proper tension wil! be maintained between belt and pulleys at all times. ...

  • Sears 113.226424 - page 9

    INSTALLING PULLEY COVER 1. Locate the pulley cover and one screw 114-20xl -3/4" 2. Place pulley cover into position shown and fasten with one screw. Do not overtighten. PULLEY COVER INSTALLING SANDING DISC PLATE 1. Locate sanding disc plate, sanding disc, one setscrew 1/4-20xl/4 inch, and a 1f8 inch hex wrench. 2. Just start screw into threade ...

  • Sears 113.226424 - page 10

    ......... SANDING disc witl =irmly int o position all 1 way SANDING OtSC INSTALLING BACKSTOP t. Locate backstop, hex bolt V4-20xIi2 inch lock- washer, and a 1/4 inch flat washer. 2. Hold backstop into position and fasten with bott and washer as shown Do not overtight: en_ WRENCH BACKSTOP LOCK BOLT INSTALLING TABLE ASSEMBLY 1: Locate table: support- ...

  • Sears 113.226424 - page 11

    4. Slide table assembly onto rod. WARNING: TO AVOID TRAPPING THE WORK OR FINGERS BETWEEN THE TABLE AND SAND- ING SURFACE, THE TABLE EDGE SHOULD BE A MAXIMUM OF 1/16-INCH FROM SANDING SUR- FACE. TABLE ASSEMBLY SHOULD BE COM- PLETELY ENGAGED ON ROD. I ROD SET SCaEW , 6. Install and tighten set screw with Alien (Hex) wrench. There is an auxiliary moun ...

  • Sears 113.226424 - page 12

    NOTE::,iT_islunit €0me_ :with:::the sanding belt ins:taiied_:_: ::i:ii: _ ..... TENSIONING ANDTRACKING DENTAL: START, I TURNSWITCH ,'OFF"_ AND REMOVE PLUG FROM POWER: SOURCE :OUT-: : LET BEFORE REMOVING OR INSTALLING SANDING BELT. USE ONLY SEARS RECOM- MENDED SANDING BELTS. SEE SEARS CATALOG. Onthe smooth side of the sanding belt you ...

  • Sears 113.226424 - page 13

    etting to know your be isc sander WARNING: TO AVOID INJURY FROM ACCI. DENTAL START, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUT. LET BEFORE MAKING ANY ADJUSTMENTS. SANDING DISC SANDING PLATE "l BACKSTOP LOCK BOLT 1 BACKSTOP BELT 2 BELT TABLE LOCKING BOLTS TABLE WORKTABLE ASSEMBLY TABLE SUPPORT ROD PULLEY 9 MOUNTING COVER ...

  • Sears 113.226424 - page 14

    z = ii ,ilii! i i ! iii ! _i! i !i ¸_¸ iii!i!i _ ¸_¸¸_¸¸'_¸ i i} !iiii_ii_iii!!!i!ii_ ¸ ii!i ¸ ili!i!_iiiil _i ¸ i ii!iil ii!!iii!il ¸!_ili_}! _ !ii ii _ i il iil ¸¸; ill ¸ i ili i_i_ i _/_ j !iiii _i i ¸ • ow d sc sander 1. To turn machine "ON:" insert key into switch. NOTE: Key is made. of yellow plastic; locate i ...

  • Sears 113.226424 - page 15

    basWc operation BEVEL SANDING The worktable can be tilted from 0 ° bevel sanding. Loosen the table lock tilt the worktable to desired angle Retighten table lock knob. 45 ° for knob and as shown. K_OB . TABLE / SUPPORT ROD Loosen rod locking toggle bolt. Slide table in so the table is no more than 1/16" from the sanding surface. WARNING: TO A ...

  • Sears 113.226424 - page 16

    TABLE WHEN IN A: HORIZONTAL a: Loosen the lock:nut usinga 314-inch wrench. b: Place a level on the abrasive belt table and using a 3/44nch wrench, screw the stop bolt in or out until the belt table is level. c. Tighten the lock nut. Arrow shows di=rection of rotation ! J SURFACE SANDING ON THE SANDING BELT Hold the workpiece firmly with both hands, ...

  • Sears 113.226424 - page 17

    ,_NDING CURVED EDGES !! ! .... CURVED EDGES Always sand inside curves on the idler pulley as shown. WARNING: NEVER ATTEMPT TO SAND THE ENDS OF A WORKPIECE ON THE IDLER PULLEY. APPLY- ING THE END OF THE WORKPIECE TO THE IDLER PULLEY COULD CAUSE IT TO FLY UP AND RESULT IN AN INJURY, Always sand outside curves on the left side of center on the sanding ...

  • Sears 113.226424 - page 18

    i, ratio CENTER WORKPIECE LEFT OF CENTE a WARNING: APPLYING THE WORKPIECE TOTHE RIGHT SIDE COULD CAUSSEI IT TO FLYIUP (KICKBACK) WHICH COULD BE HAZARDOUS. Always position the workpiece to the eft of center on sanding disc with disc rotating counter-clockwise: as shown. The table may be tilted for beveled work. L I L II JL_ _ maintenance WARNING: FO ...

  • Sears 113.226424 - page 19

    trou le shootin WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING YOUR SANDER. TROUBLE Motor will not run, Machine slows down when :sanding. ,,,,,,,, , i,,i,, Sanding Belt runs off pulleys, Wood burns while sanding. PROBABLE CAUSE 1. Defective On-Off switch. 1, Defective switc ...

  • Sears 113.226424 - page 20

    56 53 38 PARTS LIST FOR CRAFTSMAN BELT AND DISC SANDER MODEL NO. 113.226424 66 65 1 68 : : _ 69 60 4 3 2 I 1Green 37 46 45 22 24 !9 !8 17 35 34 33 32 31 3l 18 29 6 7 / 25 5 21 10 37 36 ...

  • Sears 113.226424 - page 21

    PARTS LIST FOR CRAFTSM_I BELT AND DISC SANDER MODEL NO. 113.226424 Key Part No. No. t 8t 3914 2 814101 3 813909 STD502502 805642-6 6 813915 7 STD511002 8 813920 9 813913 10 814110 11 813948 12 STD541250 13 813921 t4 814586 15 814069 16 81391 t 17 813919 18 STD551025 19 STD522505 20 813918 21 814111 22 817083 23 814109 24 814108 25 813912 26 8t 39! ...

  • Sears 113.226424 - page 22

    ...

  • Sears 113.226424 - page 23

    Notes'. 23 ...

  • Sears 113.226424 - page 24

    SERVICE HOW TO ORDER REPAIR PARTS ELTAND SANDE DISC Now that you have purchased your Belt & Disc Sander should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call or visit. The model number of your Belt and Disc Sander ...

Fabricante Sears Categoría Sander

Los documentos del dispositivo Sears 113.226424 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Sears
- manuales de instrucciones 113.226424
- hojas de producto Sears
- folletos informativos
- o etiquetas energéticas Sears 113.226424
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Sears 113.226424.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Sears 113.226424, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Sears 113.226424. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Sears 113.226424.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Sears 113.226424, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Sears 113.226424. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Sears 113.226424.

El manual de instrucciones completo de Sears debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Sears 113.226424 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Sears 113.226424, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Sears 113.226424 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Sears 113.226424 - que deben facilitarnos los primeros pasos durante el uso de Sears 113.226424
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Sears 113.226424
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Sears 113.226424 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Sears 113.226424?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sears 113.226424, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sears 113.226424 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)