-
Citrix Systems 8400 - page 1
Citrix NetScaler 10.1 Quick Start Guide: MPX 8005/8015/8200/8400/8600/8800 Platform Citrix NetScaler 10.1 ...
-
Citrix Systems 8400 - page 2
Copyright and T rademark Notice Copyright © 2013 Citrix Systems, Inc. All rights reserved. NO P AR T OF THIS DOCUMENT MA Y BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY MEANS OR USED TO MAKE DERIV A TIVE WORK (SUCH AS TRANSLA TION, TRANSFORMA TION, OR ADAPT A TION) WITHOUT THE EXPRESS WRITTEN PERMISSION OF CITRIX SYSTEMS, INC. AL THOUGH THE M ...
-
Citrix Systems 8400 - page 3
Quick Installation and Configuration W elcome to the Citrix NetScaler Application Delivery product line. Please review the following information before proceeding with installation of the MPX appliance. Before you Begin V erify that the following components and accessories are included: w One NetScaler MPX appliance w One accessory kit that contain ...
-
Citrix Systems 8400 - page 4
w Six 10/100/1000Base-T copper Ethernet ports and two 10G SFP+ ports (6x10/100/1000Base-T copper Ethernet ports + 2x10G SFP+) The following figure shows the front panel of the MPX 8005/8015/8200/8400/8600/8800 (6x10/100/1000Base-T copper Ethernet ports + 6x1G SFP) appliance. Figure 1-1. Citrix NetScaler MPX 8005/8015/8200/8400/8600/8800 (6x10/100/1 ...
-
Citrix Systems 8400 - page 5
Configuration Requirements Determine the following information for performing the initial configuration. w NetScaler IP address (NSIP): The management IP address of the appliance. The default NSIP address is 192.168.100.1. w Subnet IP address or Mapped IP address: The IP address used by the appliance to represent the client when communicating with ...
-
Citrix Systems 8400 - page 6
Figure 1-4. Rack Mounting the Appliance Appliance Precautions w Determine the placement of each component in the rack before you install the rail. w Install the heaviest appliance first, at the bottom of the rack, and then work upward. Distribute the load on the rack evenly . An unbalanced rack is hazardous. w Allow the power supply units and hard ...
-
Citrix Systems 8400 - page 7
w The handles on the left and right of the front panel of the appliance should be used only for extending the appliance out of the rack. Do not use these handles for mounting the appliance on the rack. Connecting a NetScaler Appliance to the Network Connect the interfaces on the appliance to the network ports on the appropriate switches by using Et ...
-
Citrix Systems 8400 - page 8
Figure 1-6. Connecting a Citrix NetScaler appliance to a power source Note: If you want to upgrade to the latest release of the system software before proceeding, see " Upgrading or Downgrading the System Software ." Electrical Safety Precautions Caution: During installation or maintenance procedures, wear a grounding wrist strap to avoid ...
-
Citrix Systems 8400 - page 9
Setting Up Connectivity Connect the appliance to a management workstation or the network by using the NetScaler configuration utility , the command-line interface (CLI), or the LCD keypad. Log on to the appliance as nsroot. For initial configuration, use nsroot as the administrative password. For subsequent access, use the password assigned during ...
-
Citrix Systems 8400 - page 10
w Data bits: 8 w P arity: None w Stop bits: 1 w Flow control: None Log on to the NetScaler with the following credentials: User name: nsroot P assword: nsroot T o configure the NetScaler by using the command line interface At the command prompt, type: w set ns config -ipaddress<IP Address> -netmask<subnetMask> w add ns ip <IP Address ...
-
Citrix Systems 8400 - page 11
2. NSIP address 3. Gateway The subnet mask, NSIP , and gateway values are saved in the configuration file. Y ou can then use the NSIP to connect to the appliance remotely . For more information, see " Hardware Installation ." Note: For information about deploying a high availability (HA) pair , see " Configuring High Availability .&q ...
-
Citrix Systems 8400 - page 12
Note: The LEDs on the LOM port are unoperational by design on all MPX platforms, except MPX 22040/22060/22080/22100/22120. T o Configure the NetScaler LOM Port 1. Connect the NetScaler LOM port to a management workstation or network. 2. In a web browser , type: http://192.168.1.3 . Note: The NetScaler LOM port is preconfigured with the IP address 1 ...
-
Citrix Systems 8400 - page 13
System Specifications The following table summarizes the specifications of the NetScaler MPX 8005/8015/ 8200/8400/8600/8800 appliances. Specifications MPX 8 005/8015/ 8200/8400/8600/8800 P rocessors 1 quad-core processor Memory 32 GB Number of power supplies 1 AC power supply input voltage, frequency , and current 100-240 V AC 50-60 Hz 2.5 A Maximu ...
-
Citrix Systems 8400 - page 14
Additional Information A complete set of NetScaler documentation is available on Citrix eDocs at http:// support.citrix.com/proddocs/topic/netscaler/ns-gen-netscaler-wrapper-con.html . T o contact Citrix Support, call 1-800-4-CITRIX (1-800-424-8749), or log on to MyCitrix at http://www .citrix.com . Y ou will be asked for your hardware serial numbe ...
¿Tienes una pregunta acerca de Citrix Systems 8400?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Citrix Systems 8400, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Citrix Systems 8400 probablemente compartirá una forma de solucionarlo.