-
Ryobi 454 - page 1
Rear Tine Tiller Model 454 Oper ator’ s Man ual IMPOR T ANT : READ SAFETY R ULE S AND INSTR UCTIONS CAREFULL Y MTD LLC P .O . BO X 361131 CL EVELAND , OHIO 44136-0019 Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered, brush-covered or grass-covered land unless the en ...
-
Ryobi 454 - page 2
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manu al is an important part of your new tiller. It will help you assemble, prepare and maintain the unit fo r best performance. Please read and understand what it says. Before you star t assembling your new equipment , p lease locate the model plate on th e equipment and copy th e informat ...
-
Ryobi 454 - page 3
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out import ant safety instructions whic h, if not followed, could endanger the person al safety and/or property of your self and others. Read and follow all instructions in this manual before atte mpting to operate this machine. Failur e to comply with these instructions ma ...
-
Ryobi 454 - page 4
4 7. Never operate the machine at high transport speeds on hard or slippery surfaces. 8. Exercise caution to avoid slipping or falling. 9. Look down and behind and use care when in reverse or pulling machine towards you. 10. Start the engine according to the instructions found in this manual and keep feet well away from the tines at all times. 11. ...
-
Ryobi 454 - page 5
5 SECTION 2: ASSEMBLING YOUR TILLER NOTE: R eferences to right or le ft side of the tiller are determined fr om behind the unit in the opera ting position. T o Remove Unit Fr om Carton • Remove staple s, break glue on top flaps, or cut tape at carton end an d peel along top flap to open carton. • Remove loose parts included with unit (i.e. , op ...
-
Ryobi 454 - page 6
6 • Push the cabl e through the ho le in the center of the handle and snap in t he plastic fitting. See Figure 3. Figure 3 • Remove slot head screw, nut, and two flat washers from the c lutch bail. See Figure 4. • Fasten the th readed eyebolt onto bail by securing from top with slot head screw, flat washers and lock nut. • Thread eyeb olt a ...
-
Ryobi 454 - page 7
7 NOTE: A secondary cable adjustment is available if you reach the point t hat additional adjust ment is needed. Remove the b elt cover and move the hex nuts at the other end of the cable toward s the end of the casing. Then r eadjust the hex nuts a t the handle. Tire Pre ss u re The tires on your unit may be over-inflat ed for shipping purposes. R ...
-
Ryobi 454 - page 8
8 • To shift into fo rward wheels and tine drive, push forward slightly on the gear selection handle and slowly engage the clutch control allowing the gears to synchron ize. • To stop forw ard movement and tine drive, relea se the clutch control. Do not shift gear s with the clutch control engaged except whe n engaging the tines. WARNING: Make ...
-
Ryobi 454 - page 9
9 T o Stop Engine • Move thrott le control to STOP or OFF position. • Disconnect spark p lug wire and ground to prevent accidentally starting while equipment is unattended . NOTE: After the firs t ten hours of oper ation, recheck the clutch adjustme nt. Refer to final clutch a djustment in Assembly Instructions. Setting The Depth Tilling depth ...
-
Ryobi 454 - page 10
10 SECTION 5: MAKING ADJUSTMENTS WARNING: Never attempt to make any adjustments while the eng ine is running, except where spec ified in operator’ s manual. Handle Adjustment The handle h eight may be adjusted to the desired height. Refer to the ha ndle adjustment in Know Your Tiller section. Belt T ension Adjustment Periodic adjustme nt of the b ...
-
Ryobi 454 - page 11
11 Wheel Shafts Remove wheel assemblies and lubricat e the axle shafts at least on ce a seas on. Cleaning Tine Ar ea Clean the underside of the tine shield after each use . The dirt wa shes off th e tines ea sier if rinsed off immediately instead of after it dries. Always towel dry the tiller afterwards and appl y a light coat of oil or silicone to ...
-
Ryobi 454 - page 12
12 SECTION 7: TROUBLE SHOOTING GUIDE NOTE: For r epairs beyo nd the min or adjustment s above, co ntact your local author ized service dealer. T r ouble P ossib le Cause(s) Corrective Action Engine fails to star t Fuel tank empty , or stale fuel. Throttle control le ver not in correct star ting positi on (if so equipped). Block ed fuel line. Dir ty ...
-
Ryobi 454 - page 13
13 NOTES ...
-
Ryobi 454 - page 14
14 SECTION 8: PARTS LIST FOR MODEL 454 52 13 29 55 16 53 55 16 46 31 28 12 45 17 17 44 36 6 3 33 15 27 5 36 43 4 20 40 21 1 34 18 10 42 23 7 22 36 8 47 32 37 50 25 10 9 24 36 51 34 45 26 41 36 55 16 29 19 49 44 33 14 55 16 2 14 28 35 16 14 11 48 14 54 ...
-
Ryobi 454 - page 15
15 Model 454 Ref. No. P art No. P art Description 1. 611-0020 Wheel Shaft Ass’y 33T 2. 611-0021 Tine Shaft Ass’y: 18T 3. 611-0128 Jack Shaft Ass’y 4. 611-0129 Input Shaft Ass’y 5. 617-0058 Rev. Idler Gear Ass’y: 30T 6. 617-0059 Ftine Idler Gear Ass’y: 30T 7. 617-0060 Tine Input Sprocket Ass’y: 9T 8. 617-0061 Wheel Input Sprocket Ass? ...
-
Ryobi 454 - page 16
16 Model 454 20 18 8 23 10 1 60 61 37 62 25 34 27 64 30 39 63 26 32 36 33 31 29 66 26 41 30 30 24 28 35 40 26 49 6 59 51 65 53 55 56 54 57 58 44 46 42 4 9 11 16 6 3 14 7 19 5 17 2 60 61 12 15 12 38 21 22 67 70 70 68 69 27 50 ...
-
Ryobi 454 - page 17
17 Model 454 Ref. No. P art No. P art Description 1. 747-1152 Shift Rod 2. 649-0041 Upper Handle Ass’y 3. 649-0034 Lower Handle Ass’y 4. 710 -3005 He x Scre w 3/8- 16 x 1.25 5. 710 -3056 He x Scre w 5/16 -18 x 3.25 6. 711-0415 Cle vis Pin 3/8-1.62 7. 712-0379 Flange Lock Nut 3/8-24 8. 712-0429 He x Lock Nut 5/16-18 9. 714-0147 Cotter Pin 10. 72 ...
-
Ryobi 454 - page 18
18 Model 454 18 17 24 19 27 45 44 12 26 9 6 1 8 25 14 28 20 2 11 4 22 23 16 5 21 7 13 15 3 40 43 42 41 39 32 10 31 30 29 36 34 37 38 35 10 33 ...
-
Ryobi 454 - page 19
19 Model 454 Ref. No. P art No. P art Description 1. 686-0111 Belt Cover Br ac ket Ass’y 2. 710-0237 Hex Bolt 5/16-24 x.62” 3. 710-0412 Hex Bolt 1/4-28 x.75” 4. 710-0502A He x W asher Screw 3/8-16 x 1.25” 5. 710-0152 Hex Bolt 3/8-24 x 1.0 6. 710-0599 Hex W asher Screw 7. 710-0723 Hex Cap Scre w 3/8-16 x 1.25 8. 712-0266 Lock J am Nut 3/8-16 ...
-
Ryobi 454 - page 20
MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its poss essions and territo ries. “MTD” warrants this product agai nst defects in material and workmanship for a period of two (2) years commen cing on the date of original ...
¿Tienes una pregunta acerca de Ryobi 454?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Ryobi 454, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Ryobi 454 probablemente compartirá una forma de solucionarlo.