-
Raypak D-2 POWER VENT 206A - page 1
INST ALLA TION & OPERA TING INSTR UCTIONS SWIMMING POOL & SP A HEA TER D-2 Catalog No. 6000.57.1D Effective: 05-21-10 Replaces: 10-26-06 P/N 241243 Rev . 3 W ARNING: If these instructions are not followed exactly , a fire or explosion may result causing property damage, personal injury or death. Do not store or use gasoline or other flammab ...
-
Raypak D-2 POWER VENT 206A - page 2
2 Rev . 3 reflects the following: Changes to: Parts photos on page 3, dimensional illustration on page 4, Fig. 1 and Fig. 3 on page 5, Illustrated Parts List on page 19 ...
-
Raypak D-2 POWER VENT 206A - page 3
3 RECEIVING EQUIPMENT On receipt of your equipment, it is suggested that you visually check for external damage to the carton. If the carton is damaged, it is suggested that a note be made on the Bill of Lading when signing for equipment. Remove the complete assembly from the carton. If it is damaged, report the damage to the carrier immediate- l y ...
-
Raypak D-2 POWER VENT 206A - page 4
4 INST ALLA TION REQUIREMENTS Failure to install, maintain and/or operate the Power V ent in accordance with manufacturer ʼ s instructions may result in conditions which can produce bodily injury and property damage. The equipment must be installed by a qualified installer in accordance with all local codes, or , in the absence of local codes, wit ...
-
Raypak D-2 POWER VENT 206A - page 5
5 INST ALLA TION 1 . Start off by disconnecting main power to the heater . 2. Remove the front door from the heater . See Fig 1. 3. If this is a retro-fit application, remove existing “Pagoda T op” and discard. See Fig. 2. If equipped with a drafthood, refer to drafthood installation manual for removal process. 4 . Remove the (6) Phillips screw ...
-
Raypak D-2 POWER VENT 206A - page 6
6 INST ALLA TION (Continued) 6 . Lower the jacket top back onto the heater and reinstall the (6) Phillips screws. See Fig. 3. 7. If installing on a model 266, 267, 406 or 407 heater , skip step 8. 8. T urn t he Po wer V ent u psi de do wn . Usi ng a 5/ 16” n ut dr iv er , re loc ate t he mo un tin g bra cke ts as s ho wn in F ig. 8 . 9. Place the ...
-
Raypak D-2 POWER VENT 206A - page 7
7 INST ALLA TION (Continued) 1 3. Install the right side outdoor conduit through the top 7/8” hole located on the right side of the heater . See. Fig. 13. Note: Y ou must first remove the 7/8” plug on the heater to install the hard conduit. 14. Wire the heater power lines along with the D-2 Power V ent power lines to the supply power per the wi ...
-
Raypak D-2 POWER VENT 206A - page 8
8 INST ALLA TION (Continued) 1 9. Route the 24 V AC harness through the 7/8” grommet, See Fig. 17. 20. Continue to route the harness down through any available grommet hole. See Fig. 18. 21. Wire the harness along with the installed gas valve harness per the wiring diagram. 22. Reinstall the (4) Phillips screws that hold the control panel to the ...
-
Raypak D-2 POWER VENT 206A - page 9
9 U.S. Ins tallations 1 Canad ian Inst alla tions 2 A Clear ance above gr ade , veranda, p orch , deck, or balco ny 1 ft (30 c m) 1 ft (30 c m) B Clear ance to window or do or that may b e o pened 4 ft (1.2 m) below or to side of opening; 1 foo t (30 c m) a bove op ening 3 ft (91 cm) C Clearance to perma nen tly closed window ** D V ertical clearan ...
-
Raypak D-2 POWER VENT 206A - page 10
10 VENTING (Continued) ...
-
Raypak D-2 POWER VENT 206A - page 11
11 VENTING (Continued) ...
-
Raypak D-2 POWER VENT 206A - page 12
12 VENTING (Continued) ...
-
Raypak D-2 POWER VENT 206A - page 13
13 VENTING (Continued) ...
-
Raypak D-2 POWER VENT 206A - page 14
14 SEQUENCE OF OPERA TION On call for heat, the PC board will go through its safety chain (water pressure switch, high limit 1 & 2, roll-out, etc.). When the safety chain is closed, the IID pilot will begin to spark and the pilot gas valve will open. A flame will be lit at the pilot assembly . When an acceptable signal is sent back to the PC bo ...
-
Raypak D-2 POWER VENT 206A - page 15
15 WIRING (Continued) STEP 1 : VERIFY CURRENT CONNECTIONS AS SHOWN BELOW . P/PV C/ M/MV MV PV R/BK Y/BK Y/BK V/BK V/BK V/BK Y/BK G/BK P4 1 RELA Y D-2 POWER VENT Y/BK HONEYWELL V AL VE Y/BK V/W V/BK HONEYWELL V AL VE PV MV M /MV C/ P/PV STEP 2 : DISCONNECT BOTH TERMINALS MVPV & MV AS SHOWN BELOW . D-2 POWER VENT V/BK V/W Y/BK Y/BK R/BK Y/BK V/BK ...
-
Raypak D-2 POWER VENT 206A - page 16
16 WIRING (Continued) MODELS 206, 266, 336, 406 EQUIPPED WITH HONEYWELL GAS V A LV E V/W V/BK V/BK G/BK R/BK 1 P4 D -2 POWER VENT P/PV C/ M/MV MV PV HONEYWELL V AL VE STEP 4 : CONNECT THE MAIN V AL VE LINE, FEMALE SP ADE TO MALE SP ADE AS SHOWN BELOW . D-2 POWER VENT V/BK Y/BK V/W V/BK R/BK P4 1 G/BK STEP 3 : CONNECT THE RETURN LINE, FEMALE SP ADE ...
-
Raypak D-2 POWER VENT 206A - page 17
17 WIRING DIAGRAM – MODELS 207A, 267A, 337A, 407A POWER VENT D-2 D-2 BLOWER POWER VENT GAS V AL VE HONEYWELL 1 1 + - ...
-
Raypak D-2 POWER VENT 206A - page 18
18 WIRING DIAGRAM – MODELS 206A, 266A, 336A, 406A POWER VENT D-2 D-2 BLOWER POWER VENT + - 1 1 TH TR ...
-
Raypak D-2 POWER VENT 206A - page 19
19 REPLACEMENT P ARTS NOTE: T o supply you with the correct part, it is impor- tant that you supply the heater model number , serial number and type of gas when applicable. Any part returned for replacement under standard c ompany warranties must be properly tagged with a return parts tag, completely filled in with the heater serial number , model ...
-
Raypak D-2 POWER VENT 206A - page 20
20 w w w .r ay pak .co m Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 (805) 278-5300 Fax (805) 278-5468 Litho in U.S.A. ...
¿Tienes una pregunta acerca de Raypak D-2 POWER VENT 206A?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Raypak D-2 POWER VENT 206A, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Raypak D-2 POWER VENT 206A probablemente compartirá una forma de solucionarlo.