-
Makita 6094DW - page 1
Equipped with Electric Brake MODEL 6094D MODEL 6094DW With Fast Charger Capacities INSTRUCTION MANUAL Dimensions No load speed SPEC IF I CAT IONS Model 6094D Wood screw (L x W x H) Machine screw High Low weight I Net 5.5 mm x 55 mm 6 mm 0 - 1,100 243 mm x 58 mm x 262 mm 1.6 kg (7132'' x 2~118") I 115164") I Rimin. I "R,,4,& ...
-
Makita 6094DW - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invit ...
-
Makita 6094DW - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extens ...
-
Makita 6094DW - page 4
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA ...
-
Makita 6094DW - page 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Do not short the battery cartridge: receptacle. ( ...
-
Makita 6094DW - page 6
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, pull out the set plate on the bottom of the tool and grasp both sides of the cartridge while withdrawing it from the barrel. .To insert the battery cartridge, align the tongue on the battery c ...
-
Makita 6094DW - page 7
Installing or removing driver bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Slide the sleeve toward the motor and in- sert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. NOTE : If the bit is not inserted deep enough int ...
-
Makita 6094DW - page 8
Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the revers- ing switch to the right for clockwise rota- tion or to the left for counterclockwise. CAUTION : 0 Always check the direction of rotation before operation. Use the reversing switch only when the tool comes to a complete stop. Changing the ...
-
Makita 6094DW - page 9
Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the trigger as soon as the clutch cuts in. holes to make driving easier and to pre- vent splitting of the workpiece. See the chart. wood screw (mm) 3.1 (1/8") 3.5 (9/64& ...
-
Makita 6094DW - page 10
Wood screws I 3.5 mm x 20 mm (1/8" x 3/4") I ~~~~ 4.5 mm x 20 mm W16' x 3/4") Medium hard wood I 400 screws 90 screws 60 screws 5.1 mm x 35 mm (3/16' x 1 -3/8") "5.5 mm x 50 mm (7/32" x 2") 500 screws (* . . , 400 Rlmin.) 10 ...
-
Makita 6094DW - page 11
MA1 NTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, reparis, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 1 ...
-
Makita 6094DW - page 12
ACCESSORI ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Size Phil I ips #2 #3 Slotted #5F #7F Part No ...
-
Makita 6094DW - page 13
Dec-19-86 EN CORDLESS SCREWDRIVER Model 60941) Note: The switch and other part configurations may differ from country to country. 13 ...
-
Makita 6094DW - page 14
MODEL 60940 ';"OM $:D DESCRIPTION ~ 26 27 28 29 30 31 32 33 34 35 36 37 36 39 40 41 42 43 44 45 46 47 48 49 Dec.-19-'86 EN AtD DESCRIPTION 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Pan Head Screw M4x22 IWith Washer) Pan Head Screw M4x35 IWith Washer) Housing Set lWith Item 461 Gui ...
-
Makita 6094DW - page 15
MAKmA LIMED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool freight pre ...
¿Tienes una pregunta acerca de Makita 6094DW?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 6094DW, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 6094DW probablemente compartirá una forma de solucionarlo.