Español dropdown-ico

Manual de instrucciones Humminbird TCR ID-1

32 de páginas 0.65 mb
Descargar

Pasar a la página of 32

Summary
  • Humminbird TCR ID-1 - page 1

    ...

  • Humminbird TCR ID-1 - page 2

    TABLE OF CONTENTS INSTALLATION PREPARATION………………………………………………………. 2 Parts Supplied……………………………………………………………………. 2 Accessories………………………………………………………………………. 2 Installation Overview………………………? ...

  • Humminbird TCR ID-1 - page 3

    TRANSDUCER MOUNTING PROCEDURE Humminbird’s high - speed transducer is supplied with your LCR. This transducer has been designed to give good high speed readings on most all boat designs, including aluminum. Please carefully consider the following before in stalling your transducer. TRANSDUCER MOUNTING OPTIONS A. Transom Mount - The Humminbird hig ...

  • Humminbird TCR ID-1 - page 4

    absorb the blow of any obstruction by rotating up out of the metal spring bracket without harming the transducer, or your boat. The transducer can be re - engaged by simply rotating the transducer down and snapping it b ack in place. (See Figure A) B. Inside Hull Mount - The high speed transducer can be mounted inside the hull (without pivot assemb ...

  • Humminbird TCR ID-1 - page 5

    aluminum boat locate the template on the transom between rows of rivets, or ribs that are on the bottom of the boat. Align the template so that the bottom corner of the template nearest the center of the transom is on the bottom edge of the transom. Once the location is determined mark and drill three 7/64” dia.. holes noted on the template. Atta ...

  • Humminbird TCR ID-1 - page 6

    NOTE: On boats with more than 15 degree deadrise angle it may be necessary to mount the transducer slightly off parallel with the water level. (See Figure E) Mark and drill the three 9/64” dia. holes as shown on the template. Attach the metal bracket using the three #10 self threading screws supplied. Be sure to align the holes so that they are c ...

  • Humminbird TCR ID-1 - page 7

    Step 4 TRANSDUCER ASSEMBLY - Insert the transducer assembly into the metal bracket from the bottom. Push up until the holes in the plastic pivot align with the uppermost holes in the bracket. Slide the O - ring on to the headed pin and insert it through th e two parts. Assemble by screwing the ¼”x3/8” allen head screw into the end of the pin a ...

  • Humminbird TCR ID-1 - page 8

    using the 5/32” allen wrench provided. The screws are visible through the access holes on each side of the metal bracket. Check to make sure the transducer main body is rigidly fastened to the pivot. (See Figure H) Step 6 CHECK POSITION OF TRANSDUCER - At this point, check to see that the bottom of the transducer is a minimum of ¼” below the b ...

  • Humminbird TCR ID-1 - page 9

    4. Put transducer in the water. The bottom of the transducer should be in a flat area and should be in good contact with the bottom of the boat. 5. Operate the LCR with the boat operating at high speed. The transducer may have t o be moved in order to find an area where satisfactory operation is observed. 6. When an area is found that produces sati ...

  • Humminbird TCR ID-1 - page 10

    INSTALLING THE LCR The LCR should be mounted on a flat, solid surface for maximum stability. The low profile swivel mount has four holes drilled in the base. It is recommended that all four holes be used. Position the swivel base and drill four ¼” diameter holes. Note: The LCR hole pattern Is the same as for all Humminbird flasher units. Use har ...

  • Humminbird TCR ID-1 - page 11

    OTHER MOUNTING OPTIONS 1. The LCR gimbal bracket can also be mounted on the SM - 4, quick disconnect swivel mount. 2. The LCR gimbal bracket can also be mounted directly to the dash without the swivel mount, however, this method is not recommended since the unit cannot be rotated. INSTALLING THE CABLES Your LCR comes equipped with Humminbird’s ne ...

  • Humminbird TCR ID-1 - page 12

    “Transducer”. Note: An adapter (AD - 4) is available to allow use of an old waterproof (BNC) transducer with the LCR, but be sure that the transducer is a 16degree. A 32 - degree transducer cannot be used. A 11/8” hole must be drilled to pull thr ough the transducer connector. After drilling the hole, pull the transducer connector up through ...

  • Humminbird TCR ID-1 - page 13

    INSTALLATION TEST THE INSTALLATION TEST THE INSTALLATION Testing should be performed with the boat in the water, however you can initially confirm basic operation with the boat trailered. Press POWER once to turn the unit on. There will be an audible chirp when any button is pressed to confirm the button press. If the unit does not power - up, ensu ...

  • Humminbird TCR ID-1 - page 14

    USING THE TCR ID - 1 FEATURES AND FUNCTIONS ...

  • Humminbird TCR ID-1 - page 15

    USING THE TCR ID - 1 HOW SONAR WORKS HOW SONAR WORKS Humminbird depth sounders work on the basic principles of sonar. An electronic signal generated in the unit is changed to an ultrasonic signal by the transducer or Sensor, which sends the signal toward the bottom. The signal travels downward until it strikes either the bottom or an object above t ...

  • Humminbird TCR ID-1 - page 16

    USING THE TCR ID - 1 HOW SONAR WORKS Compact, High - Definition Sensor. To send and receive this higher - frequency signal, we developed a new High - Definition Sensor. You can immediately see the difference between our 455KHz Sensor and older 200KHz transducers. This unique new Sensor makes bulky low - definition transducers a thing of the past. O ...

  • Humminbird TCR ID-1 - page 17

    USING THE TCR ID - 1 BUILT - IN SIMULATOR BUILT - IN SIMULATOR To help you learn to use your new unit, Humminbird has built a simulator into the TCR ID - 1.The simulator will display a typical u nderwater scene, and allow you to use the con trols for practice. Activating the simulator is easy - with the unit turned off, hold down the power button f ...

  • Humminbird TCR ID-1 - page 18

    USING THE TCR ID - 1 READING THE TCR ID - 1 SCREEN READING THE TCR ID - 1 SCREEN Your TCR has a liquid crystal display, or LCD. The liquid crystal material in the display aligns it self to either block light or let light pass through. This blocking of light creates im ages on the screen. Since the display depends on light to form its images, increa ...

  • Humminbird TCR ID-1 - page 19

    USING THE TCR ID - 1 READING THE TCR ID - 1 SCREEN Total Screen Update  Humminbird’s exclusive Total Screen Update instantly updates the entire TCR screen to include new information each time a func tion is changed no waiting for the changes to “march” onto the screen. This feature is valuable in 2 ways: 1. Changing depth ranges. When the ...

  • Humminbird TCR ID-1 - page 20

    USING THE TCR ID - 1 READING THE TCR ID - 1 SCREEN Of course, the best way to learn to read your TCR ID - 1 is to use it, especially in familiar lo cations. If you know what's underwater and can see it display ed on the screen, then you're on your way to being an experienced TCR user. ...

  • Humminbird TCR ID-1 - page 21

    USING THE TCR ID - 1 OPERATING THE TCR ID - 1 OPERATING THE TCR ID - 1 Your new TCR ID - 1 offers unique automatic features, as well as many adjustable ones. If you're learning to ope rate the TCR ID - 1 with its simulator, follow the directions listed at “Built - In Simulator” on page 16, and then come back to this page. If you’re learn ...

  • Humminbird TCR ID-1 - page 22

    USING THE TCR ID - 1 OPERATING THE TCR ID - 1 Example 2: Often - used function. If you think you'll be using zoom often, you can go to the zoom function, let the instructions disappear, and then acti vate the zoom whe n you need it simply by pressing On/Off. The following describes the functions and how to use them, in order of appearance afte ...

  • Humminbird TCR ID-1 - page 23

    USING THE TCR ID - 1 OPERATING THE TCR ID - 1 Once the instructions have disappeared from the screen, it's easy to tell which alarm you have activated - the alarm for all fish shows both small and large fish sym bols at the bottom of the screen, while the “large only” alarm displays only a large fish symbol. 4. Zoom Automatic setting: off ...

  • Humminbird TCR ID-1 - page 24

    USING THE TCR ID - 1 OPERATING THE TCR ID - 1 7. Depth R ange Automatic setting: on The TCR automatically finds the bottom and then sets and displays the ideal depth range when you turn the unit on. If you choose to leave the auto range change on, the bottom will remain "blacked in" for easy - to - understand read ings, and the depth rang ...

  • Humminbird TCR ID-1 - page 25

    SPECIFICATIONS Operating Frequency 455KHz Power Requirement 12 volts Power Cable Length 11½’ Sensor (s tandard) SHS - 6 - 16 High - Definition, high - speed Sensor Cone Angle 16 degrees Sensor Cable Length 20’ Depth Ranges 0 - 15’, 0 - 30’, 0 - 60’, 0 - 120’ Zoom Ranges 7½’, 15’ Mounting (standard) All - in - One Mounting & Co ...

  • Humminbird TCR ID-1 - page 26

    MAINTENANCE AND WARRANTY MAINTENANCE MAINTENANCE Your Humminbird fishfinder is designed to provide years of t rouble free operation with virtually no maintenance. Follow these simple procedures to ensure your Humminbird continues to deliver top performance. • If the unit comes into contact with salt spray simply wipe the affected surfaces with a ...

  • Humminbird TCR ID-1 - page 27

    MAINTENANCE AND WARRANTY TROUBLESHOOTING TROUBLESHOOTING Do not attempt to repair the fishfinder yourself. There are no user serviceable parts inside, and sp ecial tools and techniques are required for reassembly to ensure the waterproof integrity of the housing. Repairs should be performed only by authorized Humminbird technicians. Many requests f ...

  • Humminbird TCR ID-1 - page 28

    MAINTENANCE AND WARRANTY TROUBLESHOOTING Second, inspect the transducer cable from end to end for breaks, kinks, or cuts in the outer casing of the cable. Also ensure the transducer is fully submerged in water. If the transducer is connected to the unit through a switch, temporarily connect it directly to the un it and try again. If none of these i ...

  • Humminbird TCR ID-1 - page 29

    MAINTENANCE AND WARRANTY TROUBLESHOOTING 5. The unit comes on before I press POWER, and won't turn off. Check the transducer cable. If the outer jacket of the cable has been cut and the cable is in contact with bare metal, you need to repair the cut with electrical tape. If there is no problem with the cable, disconnect the transducer from t h ...

  • Humminbird TCR ID-1 - page 30

    MAINTENANCE AND WARRANTY WARRANTY HUMMINBIRD ONE YEAR FULL WARRANTY First year repairs (from original date of purchase) on your Humminbird fishfinder are absolutely free. This does not include physica l damage to the unit or its accessory items. Any modification or attempt to repair the original equipment or accessories by unauthorized individuals ...

  • Humminbird TCR ID-1 - page 31

    MAINTENANCE AND WARRANTY SERVICE POLICY SERVICE POLICY This Service Policy is valid in the United States only. This applies to Humminbird units returned to our factory in Eufaula, Alabama, and is subject to ch ange without notice. All repair work is performed by factory - trained technicians to meet exacting factory specifications. Factory serviced ...

  • Humminbird TCR ID-1 - page 32

    MAINTENANCE AND WARRANTY CUSTOMER SUPPORT CUSTOMER SUPPORT If you have any questions, call our Humminbird Customer Support Hotline: 1 - 334 - 687 - 0503 Throughout the U. S. and Canada, hours are Monday - Friday, 8:00 a.m. to 5:00 p.m. Central time. If after reading “Troubleshooting” you determine your unit needs factory service, please attach ...

Fabricante Humminbird Categoría Fish Finder

Los documentos del dispositivo Humminbird TCR ID-1 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Humminbird
- manuales de instrucciones TCR ID-1
- hojas de producto Humminbird
- folletos informativos
- o etiquetas energéticas Humminbird TCR ID-1
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Humminbird TCR ID-1.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Humminbird TCR ID-1, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Humminbird TCR ID-1. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Humminbird TCR ID-1.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Humminbird TCR ID-1, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Humminbird TCR ID-1. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Humminbird TCR ID-1.

El manual de instrucciones completo de Humminbird debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Humminbird TCR ID-1 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Humminbird TCR ID-1, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Humminbird TCR ID-1 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Humminbird TCR ID-1 - que deben facilitarnos los primeros pasos durante el uso de Humminbird TCR ID-1
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Humminbird TCR ID-1
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Humminbird TCR ID-1 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Humminbird TCR ID-1?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Humminbird TCR ID-1, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Humminbird TCR ID-1 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)