-
Chicago Electric 94626 - page 1
3-3/8 INCH BLADE T OE KICK SA W 94626 ASSEMBL Y AND OPERA TING INSTR UCTIONS Visit our website at: http://www .harborfreight.com Read this material bef ore using this product. F ailure to do so can result in serious injury . SA VE THIS MANU AL. Cop yright © 2006 b y Harbor F reight T ools ® . All rights reser ved. No por tion of this manual or an ...
-
Chicago Electric 94626 - page 2
P age 2 SKU 94626 F or technical questions, please call 1-800-444-3353 SPECIFICA TIONS SA VE THIS MANU AL Y ou will need the manual f or the safety w arnings and precautions, assembly instructions, operating and maintenance procedures , par ts list and diagram. K eep y our inv oice with this manual. Write the inv oice number on the inside of the fr ...
-
Chicago Electric 94626 - page 3
P age 3 SKU 94626 F or technical questions, please call 1-800-444-3353 Electrical Safety 4. A void bod y contact with gr ounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased r isk of electric shock if y our body is grounded. 5. Do not expose po wer tools to rain or wet conditions. W ater entering a power tool w ...
-
Chicago Electric 94626 - page 4
P age 4 SKU 94626 F or technical questions, please call 1-800-444-3353 14. Do not overreac h. Keep pr oper footing and balance at all times. Proper f ooting and balance enables better control of the po wer tool in unexpected situations . 15. Use safety equipment. Alwa ys wear ANSI-appr oved e ye protection. Dust mask, non-skid saf ety shoes or hear ...
-
Chicago Electric 94626 - page 5
P age 5 SKU 94626 F or technical questions, please call 1-800-444-3353 SPECIFIC SAFETY R ULLES FOR THIS PR ODUCT 1. D ANGER! Keep hands awa y from cutting area and blade. Keep y our second hand on auxiliary handle or motor housing. If both hands are holding the sa w , the y cannot be cut by the b lade. K eep your body positioned to either side of t ...
-
Chicago Electric 94626 - page 6
P age 6 SKU 94626 F or technical questions, please call 1-800-444-3353 If the blade becomes twisted or misaligned in the cut, the teeth at the bac k edge of the b lade can dig into the top surf ace of the wood causing the blade to climb out of the kerf and jump bac k toward the oper ator . Kickbac k is the result of tool misuse and/ or incorrect op ...
-
Chicago Electric 94626 - page 7
P age 7 SKU 94626 F or technical questions, please call 1-800-444-3353 W ARNING! P eople with pacemaker s should consult their physician(s) bef ore using this product. Operation of electrical equipment in close pr o ximity to a hear t pacemaker could cause interference or failure of the pacemaker . Some dust created by power sanding, sawing, grindi ...
-
Chicago Electric 94626 - page 8
P age 8 SKU 94626 F or technical questions, please call 1-800-444-3353 Double Insulated T ools with T w o Pr ong Plugs 4. This product has a polarized plug (one blade is wider than the other) as a f eature to reduce the risk of electr ic shoc k. This plug will fit in a polarized outlet only one wa y . If the plug does not fit fully in the outlet, ...
-
Chicago Electric 94626 - page 9
P age 9 SKU 94626 F or technical questions, please call 1-800-444-3353 SYMBOLOGY T able B UNP A CKING When unpacking, chec k to make sure that all the par ts are included. The unit comes fully assembled. Refer to the Assemb ly section, and the Assembly Dra wing and P ar ts List at the end of this manual. If an y par ts are missing or broken, please ...
-
Chicago Electric 94626 - page 10
P age 10 SKU 94626 F or technical questions, please call 1-800-444-3353 Contr ols Making Flush Cuts 1. Place the Saw where the flush cut is to be made . See photo below . When making a cut under a toe-kick (i.e ., under a cabinet), inser t the Saw at an angle , then low er it to the floor surf ace. See illustrations on the ne xt page. 2. Plug the ...
-
Chicago Electric 94626 - page 11
P age 11 SKU 94626 F or technical questions, please call 1-800-444-3353 Caution: Never pull the Saw backwar ds since the Saw Blade will climb out of the cut and kickbac k will occur . INSPECTION, MAINTENANCE, AND CLEANING W ARNING! Make sure the T rigger Switch of the Flush Cut Saw is in its “OFF” position, and that the tool is unplugged fr om ...
-
Chicago Electric 94626 - page 12
P age 12 SKU 94626 F or technical questions, please call 1-800-444-3353 Installing the Saw Blade 1. Use only a 3-3/8 inch Saw Blade (2) r ated to at least 4500 RPM. 2. Unplug the Saw P o wer Cord (54) from the electrical outlet. 3. W earing work glov es, r aise the Blade Guard (6) as f ar as possib le. 4. Hold the Blade Guard up and press the spind ...
-
Chicago Electric 94626 - page 13
P age 13 SKU 94626 F or technical questions, please call 1-800-444-3353 NO TE : Some par ts are listed and shown for illustration pur poses only and are not av ailable individually as replacement par ts. PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DI STRIB UT OR HAS PRO VIDED THE P AR TS DIA GRAM IN THIS MANU AL AS A REFER ENCE ...
-
Chicago Electric 94626 - page 14
P age 14 SKU 94626 F or technical questions, please call 1-800-444-3353 ASSEMBL Y DRA WING ...
-
Chicago Electric 94626 - page 15
P age 15 SKU 94626 F or technical questions, please call 1-800-444-3353 LIMITED 90 D A Y W ARRANTY Harbor F reight T ools Co . mak es ev er y ef f or t to assur e that its products meet high quality and durability standards, and warr ants to the original purchaser that this product is free from def ects in materials and workmanship for the period o ...
¿Tienes una pregunta acerca de Chicago Electric 94626?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Chicago Electric 94626, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Chicago Electric 94626 probablemente compartirá una forma de solucionarlo.