-
N-Tron 405FX-ST - page 1
(Revised 2010- 11 - 15 ) 1 400 Series Industrial Et hernet Switch es Installation Guide ...
-
N-Tron 405FX-ST - page 2
(Revised 2010- 11 - 15 ) 2 Industrial Ethe rnet Switch Insta llation Guide 405TX 405FX- SC 405FX- ST 405FXE- SC - YY 405FXE- ST - YY Where: YY = -15, -40, or -80 ...
-
N-Tron 405FX-ST - page 3
(Revised 2010- 11 - 15 ) 3 Copyright, © N- TR ON Corp., 2008 820 S. University Blvd., Suite 4E Mobile, AL 36609 USA All rights reserved. Reproduction, adaptation, or translation without prior written permission from N -TRON Corp. is prohibited, except as allowed under copyright laws. Ethernet is a re gistered t rademark of Xerox Cor poration. All ...
-
N-Tron 405FX-ST - page 4
(Revised 2010- 11 - 15 ) 4 Safety Warnings ELECTRICAL SAFETY WARNING: Do not disconnect while circuit is live, unless area is known to be non-hazardous. WARNING: Disconnect the power cable before removing the enclosure top. WARNING: Do not operate the unit with the top cover removed. WARNING: Properly ground the unit before connecting anything else ...
-
N-Tron 405FX-ST - page 5
(Revised 2010- 11 - 15 ) 5 405FX, 405FXE, & 405TX Industrial Ethernet Switches The 405TX and 405FX Unmanaged Industrial Etherne t Switches support high speed la yer 2 switching between ports. The 405TX is an affordable 5 port unmanaged switch that is capable of auto negotiating 10/100 Mb and half/full duplex communications. The N -TRON 405TX is ...
-
N-Tron 405FX-ST - page 6
(Revised 2010- 11 - 15 ) 6 PACKAGE CONTENTS Please make sure the Ethernet Switch package contains the following items: 1. 405FX/405FXE/405TX Ethernet Switch 2. This Installation Guide Contact your carrier if any items are damaged. INSTALLATION Read the following warning before beginning the installation: WARNING The 405FXE unit contains a Class 1 L ...
-
N-Tron 405FX-ST - page 7
(Revised 2010- 11 - 15 ) 7 405FX/405FXE H ALF DUPLEX SETUP While all RJ45 ports are Autosensing, the 405FX/405FXE Fiber Optic Port is factory configured for full duplex operation. In the event half duplex operation is desired, follow these steps: 1. Remove the Voltage Input Power Plugs. 2. Remove the top cover (8 screws). 3. Remove the jumper plug ...
-
N-Tron 405FX-ST - page 8
(Revised 2010- 11 - 15 ) 8 DIN-Rail Mounting Install the unit in a standard D IN- Rail. Recess the unit to allow at least 5” of horizontal clearance for fiber optic cable bend radius (2” for TX models). Note: This unit may be mounted horizontally or verticall y. To install the unit to 35 mm indus trial DIN-Rail - Place the top edge of the inclu ...
-
N-Tron 405FX-ST - page 9
(Revised 2010- 11 - 15 ) 9 FRONT PANEL From Left to Right: LNK Link LED for Fiber Optic Port (405FX/FXE only) TX Fiber Optic Transmit Port (405FX/FXE Only) RX Fiber Optic Receive Port (405FX/FXE Only) ACT Activity LED for Fiber Optic Port (405FX/FXE only) X RJ45 Crossover Uplink Port (405TX Only) RJ45 Ports Auto sensing 10/100BaseT Connections ! Re ...
-
N-Tron 405FX-ST - page 10
(Revised 2010- 11 - 15 ) 10 LED’s: The table below describes the operating modes: LED Color Description GREEN Power is Applied OFF Power is OFF ! RED Controller HW Error OFF No Errors. Normal Operation. LNK GREEN Link between ports established OFF No Link between ports ACT GREEN Data is active between ports OFF Data is inactive between ports APPL ...
-
N-Tron 405FX-ST - page 11
(Revised 2010- 11 - 15 ) 11 N-TRON SWITCH GROUNDING TECHNIQUES The grounding philosophy of any control system is an integral part of the design. N -Tron switches are designed to be grounded, but the user has been given the flexibility to float the switch when r equired. T he best noise immunity and emissions (i.e. CE) are obtained when the N-Tron s ...
-
N-Tron 405FX-ST - page 12
(Revised 2010- 11 - 15 ) 12 RJ45 CONNECTOR CRIMP SPECIFICATIONS Please reference the illustration below for your Cat5 cable spe cifications: ...
-
N-Tron 405FX-ST - page 13
(Revised 2010- 11 - 15 ) 13 CONNECTING THE UNIT For 405 FX & 405FXE units, remove the dust cap from the fiber optic connect ors and connect the fiber optic cables. The TX po rt on the 405 FX should be connected to the RX port of the far end station. Th e RX port on the 405FX should be connected to the TX port of the far end station. For 10/100 ...
-
N-Tron 405FX-ST - page 14
(Revised 2010- 11 - 15 ) 14 KEY SPECIFICATIONS Physical Height: 2.13" (5.41 cm) Width: 5.00" (12.70 cm) Depth: 3.00" (7.62 cm) Weight: ~ 1.2 lbs. (0.6 kg) (Note: can be mounted horizontally or vertically) Electrical Input Voltage: 10-30 VDC (Regulated) Input Current: 220mA max. @ 24VDC (Steady State) Inrush Current: 14.0Amp/0.9ms max ...
-
N-Tron 405FX-ST - page 15
(Revised 2010- 11 - 15 ) 15 Regulatory Approvals: Safety: Suitable for use in Class I, Division 2, Groups A, B, C, and D Hazardous Loc ations, or Non-hazardous locations only. EMI: EN55022 – Class A FCC Part 15 Class A EMS: EN55024:1998 EN61000-4-2:1995 EN61000-4-3:1997 EN61000-4-4:1995 EN61000-4-5:1995 EN61000-4-6:1996 GOST- R Certified. Warrant ...
-
N-Tron 405FX-ST - page 16
(Revised 2010- 11 - 15 ) 16 N-TRON Limited Warranty N-TRON, Corp. warrants to the end user that t his hardware product will be fr ee fro m d efects in w ork manship and materials, under nor mal use a nd service, for the applicab le w arranty period fro m the date of purchase from N -TRON or its authorized reseller. If a product does not op erate as ...
¿Tienes una pregunta acerca de N-Tron 405FX-ST?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con N-Tron 405FX-ST, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con N-Tron 405FX-ST probablemente compartirá una forma de solucionarlo.