-
Husqvarna 1130STE XP - page 1
1130STE XP Owner's Manual ...
-
Husqvarna 1130STE XP - page 2
2 Safe Operation Practices f or Snow Thro wers IMPORT ANT : This machine is capable of amputating hands and f eet and throwing objects. F ailure to obser v e the follo wing saf ety instructions could result in ser ious injur y or death. SAFETY R ULES W ARNING: This snow thrower is for use on sidewalks, driveways and other ground le vel surfaces. Ca ...
-
Husqvarna 1130STE XP - page 3
3 PR ODUCT SPECIFICA TIONS Gasoline Capacity 4.0 Quar ts and T ype: Unleaded Regular only Oil T ype SAE 30 (abov e 40°F) (API SG–SL): SAE 5W-30 or 10W -30 (0° to +40°F) SAE 0W -30 (below 0°F) Oil Capacity: 26 Ounces Spark Plug: Champion RN4C (Gap: .030") • Do not put hands or feet near or under rotating parts. K eep clear of the discha ...
-
Husqvarna 1130STE XP - page 4
4 P AR TS P A CKED SEP ARA TEL Y IN CAR T ON MAINTENANCE ..................................................... 14-15 MAINTENANCE SCHEDULE ..................................... 14 SER VICE AND AD JUST MENTS ........................... 16-18 ST ORA GE ................................................................... 18 TROU BLE SHOO T ING ......... ...
-
Husqvarna 1130STE XP - page 5
5 ASSEMBL Y / PRE-OPERA TION Read these instructions and this man u al in its entirety before y ou attempt to assemble or oper ate your ne w snow throw er . Y our new sno w thrower has been as sem bled at the f actor y with the ex cep tion of those par ts left unassembled f or shipping pur poses. All par ts such as nuts , washers, bolts , etc., nec ...
-
Husqvarna 1130STE XP - page 6
6 ASSEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE RO T A TER HEAD (See Fig. 7) NO TE: The multi-wrench provided in y our par ts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening tow ard front of snow throw er . 2. P osition chute rotater head ov er chute brac ...
-
Husqvarna 1130STE XP - page 7
7 ASSEMBL Y / PRE-OPERA TION INST ALL CHUTE DEFLECTOR REMO TE CONTROL (See Figs. 8 and 9) 1. Install remote cable br ack et to discharge chute with 5/16-18 carriage bolt, 5/16 fl at w asher and 5/16-18 lockn ut as shown. Tighten securely . 2. Install remote cable e yelet to chute defl ector with 1/4-20 shoulder bolt, nylon friction washer and 1/4 ...
-
Husqvarna 1130STE XP - page 8
8 OPERA TION KNO W Y OUR SNO W THR O WER READ THIS OWNER'S MANU AL AND ALL SAFETY RULES BEFORE OPERA TING Y OUR SNO W THRO WER. Compare the illustrations with y our snow throw er to familiarize y ourself with the location of various controls and adjustments. Sav e this manual f or future ref erence. These symbols may appear on y our snow thro ...
-
Husqvarna 1130STE XP - page 9
9 MEETS A.N.S.I. SAFETY REQUIREMENTS Our snow thro wers conf or m to the standards of the American National Standards Institute. FIG. 11 OPERA TION Drive speed control le ver - used to select f orward or re verse motion and speed of sno w thrower . T raction drive contr ol lever - used to engage po wer-pro- pelled for w ard or rev erse motion of sn ...
-
Husqvarna 1130STE XP - page 10
10 OPERA TION T O CONTROL SNO W DISCHARGE (See Fig. 15) W ARNING: Snow thr ower s have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thro wn from the disc harge chute. Keep the area of operation c lear of all persons, small children and pets at all times including startup. W ARNING: If the discharge chute ...
-
Husqvarna 1130STE XP - page 11
11 T O MO VE FOR W ARD AND BA CKW ARD (See Fig. 18) SELF-PROPELLING, f orward and re verse mo vement of the snow thro wer , is controlled by the traction drive control le ver located on the left side handle . • Squeeze traction drive control le ver to handle to en gage the drive system. • Release traction driv e control lev er to stop the forwa ...
-
Husqvarna 1130STE XP - page 12
12 T O ADJUST SKID PLA TES (See Fig. 20) NO TE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scr aper bar and the ground surf ace. Adjust skid plates e v enly to proper height f or current surface conditions . For remo v al ...
-
Husqvarna 1130STE XP - page 13
13 T O ST ART ENGINE • Be sure fuel shut-off v alve is in the OPEN position. Y our snow thro wer engine is equipped with both a 120 V olt A.C . electr ic star ter and a recoil star ter . The electr ic star ter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A.C . household current. • Be sure your house ...
-
Husqvarna 1130STE XP - page 14
14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this sno w throw er does not cov er items that hav e been sub ject ed to operator abuse or negligence. T o receive full v alue from the warranty , operator must maintain snow thro wer as in str uct ed in this manual. Some ad just - ments will need to be made periodically ...
-
Husqvarna 1130STE XP - page 15
15 MAINTENANCE SNO W THRO WER Alwa ys obser ve saf ety rules when performing main te nance. TIRES • Maintain proper air pressure in both tires (See “PROD- UCT SPECIFICA TIONS” section in this manual). • K eep tires free of gasoline / oil, which can har m rubber . NO TE: T o seal tire punctures and prev ent fl at tires due to slo w leaks, t ...
-
Husqvarna 1130STE XP - page 16
16 SER VICE AND ADJUSTMENTS W ARNING: T o av oid serious injur y , before perf orming any service or ad- just ments: 1. Be sure throttle is in ST OP position. 2. Remove safety ignition ke y . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come in c ...
-
Husqvarna 1130STE XP - page 17
17 SER VICE AND ADJUSTMENTS T O REPLA CE BEL TS (See Fig. 25) The auger and traction drive belts are not adjustab le. If the belts are damaged or begin to slip from wear , they should be replaced. It is recommended that the belt(s) be replaced by a qualifi ed service center . NO TE: It is recommended that both the auger and traction drive belt be ...
-
Husqvarna 1130STE XP - page 18
18 ST ORA GE Immediately prepare your sno w thrower f or storage at the end of the season or if the unit will not be used for 30 da ys or more. W ARNING: Never store the sno w thro wer with gaso line in the tank in side a build ing where fumes may reach an open fl ame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap p ...
-
Husqvarna 1130STE XP - page 19
19 Does not start 1. Fuel shut-off v alve (if so 1. T ur n fuel shut-off valv e to OPEN position. equipped) in OFF position. 2. Saf ety ignition ke y 2. Insert safety ignition k ey . is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in ST OP position. 4. Mov e throttle to F AST position. 5. Choke in OFF position. 5. Mo ve to FULL posi ...
-
Husqvarna 1130STE XP - page 20
20 REP AIR P ARTS A UGER HOUSING / IMPELLER ASSEMBL Y SNO W THRO WER - MODEL NO . 1130STE XP (HU1130STC), PR ODUCT NO . 954 22 30-81 22 18 21 53 19 1 3 2 6 6 5 6 6 9 12 7 7 8 6 11 27 27 30 26 25 24 23 20 31 25 24 26 23 29 21 54 53 19 20 18 10 13 4 14 16 15 36 37 50 47 42 44 27 43 46 38 45 27 43 42 41 40 39 34 32 49 19 48 51 33 35 24 25 20 19 21 52 ...
-
Husqvarna 1130STE XP - page 21
21 KEY P ART NO . NO . DESCRIPTION 1 532 18 86-63 Bar , Weight 2 532 16 67-85 Nut, Hex 5/16-18 3 872 11 05-10 Bolt, Carr iage 5/16-18 x 1-1/4 4 532 19 10-79 Pulley , Impeller 5 532 18 89-09 Bearing Assembly , Flange 6 532 15 53-77 Nut, Hex Flange 5/16-18 7 532 18 03-55 Bolt, Flat Head, Carr iage 5/16-18 x 5/8 8 872 27 05-05 Bolt, Carr iage 5/16-1 8 ...
-
Husqvarna 1130STE XP - page 22
22 REP AIR P ARTS CONTR OL P ANEL / DISCHARGE CHUTE SNO W THRO WER - MODEL NO . 1130STE XP (HU1130STC), PR ODUCT NO . 954 22 30-81 3 2 1 1 2 6 19 2 2 14 26 28 27 27 25 20 29 31 30 16 18 17 10 14 3 13 15 9 22 11 12 7 4 5 6 8 8 21 21 23 24 23 ...
-
Husqvarna 1130STE XP - page 23
23 REP AIR P ARTS CONTR OL P ANEL / DISCHARGE CHUTE SNO W THRO WER - MODEL NO . 1130STE XP (HU1130STC), PR ODUCT NO . 954 22 30-81 KEY P ART NO . NO . DESCRIPTION 1 532 18 33-34 Knob , Lev er 2 817 50 10-10 Screw #10-24 x 5/8 3 532 17 86-74 Control Assembly , Defl ector 4 873 80 06-00 Nut, Lock 3/8-16 5 819 13 13-16 W asher , Flat 3/8 6 532 17 86- ...
-
Husqvarna 1130STE XP - page 24
24 REP AIR P ARTS HANDLES SNO W THRO WER - MODEL NO . 1130STE XP (HU1130STC), PR ODUCT NO . 954 22 30-81 5 11 12 15 7 10 33 18 19 37 34 35 20 20 21 21 6 11 5 36 13 2 5 15 11 4 4 3 3 16 17 16 23 22 38 39 24 27 26 24 25 27 40 22 17 1 4 4 14 5 8 6 28 9 32 30 31 31 32 ...
-
Husqvarna 1130STE XP - page 25
25 KEY P ART NO . NO . DESCRIPTION 1 532 18 41-10 Lev er , Auger Control, RH 2 532 18 41-09 Lev er , T raction Drive Control, LH 3 532 17 94-39 Nut, Cage 1/4-20 4 532 17 88-88 Bushing, Flange 5 532 16 96-75 Retainer , Hair pin 6 532 18 04-02 Screw , He x Head 1/4-20 x 3/4 7 532 17 86-52 Rod, Interlock 8 532 18 40-03 T ube Assembly , Interlock, RH 9 ...
-
Husqvarna 1130STE XP - page 26
26 REP AIR P ARTS DRIVE SNO W THRO WER - MODEL NO . 1130STE XP (HU1130STC), PR ODUCT NO . 954 22 30-81 35 33 15 41 22 34 29 22 31 26 7 2 43 2 11 3 3 25 24 23 12 32 27 44 20 21 21 22 16 17 42 15 2 1 4 13 4 1 2 5 3 4 2 5 3 3 5 1 2 3 13 1 5 2 7 8 9 10 6 3 3 41 14 2 19 18 28 30 40 39 38 36 37 33 ...
-
Husqvarna 1130STE XP - page 27
27 KEY P ART NO . NO . DESCRIPTION 1 532 14 63-15 Screw , He x Head 5/16-18 x 3/4 2 873 80 05-00 Nut, Lock 5/16-18 3 532 15 54-15 W asher , Flat 4 817 49 05-08 Screw , He x Head 5/16-18 x 1/2 5 532 18 00-17 Bearing, Flange 6 532 18 01-34 Shaft, Auxiliary 7 532 17 92-70 Spacer , Plate 8 532 19 29-07 Plate, A uxiliar y 9 532 18 00-82 Gear , Intermedi ...
-
Husqvarna 1130STE XP - page 28
28 REP AIR P ARTS CHASSIS / ENGINE / PULLEYS SNO W THRO WER - MODEL NO . 1130STE XP (HU1130STC), PR ODUCT NO . 954 22 30-81 6 19 17 10 21 22 23 2 1 3 4 6 7 8 9 12 13 15 27 26 25 24 18 7 6 20 14 30 29 31 31 47 47 48 46 40 44 26 49 50 51 52 35 55 34 33 32 38 36 41 6 37 39 42 43 11 53 54 5 11 44 26 45 41 11 16 10 21 28 6 ...
-
Husqvarna 1130STE XP - page 29
29 REP AIR P ARTS CHASSIS / ENGINE / PULLEYS SNO W THRO WER - MODEL NO . 1130STE XP (HU1130STC), PR ODUCT NO . 954 22 30-81 KEY P ART NO . NO. DESCRIPTION 1 532 18 10-44 Spring, T raction Idler 2 532 18 05-22 Pulley , Idler (2-1/4) 3 - - - Engine, T ecumseh, Model Number OH3185A-221807B (F or engine ser vice and replacement par ts, call T ecumseh P ...
-
Husqvarna 1130STE XP - page 30
30 REP AIR P ARTS WHEELS / DECALS SNO W THRO WER - MODEL NO . 1130STE XP (HU1130STC), PR ODUCT NO . 954 22 30-81 10 32 30 15 18 17 19 10 12 31 2 7 4 3 4 13 20 11 21 33 22 23 24 10 10 25 26 28 27 29 28 29 10 10 27 26 28 23 22 33 20 11 14 9 7 4 5 6 1 2 4 3 12 13 14 32 30 25 24 19 21 16 10 10 15 18 8 5 3 4 2 10 7 6 8 9 11 12 1 11 3 13 ...
-
Husqvarna 1130STE XP - page 31
31 REP AIR P ARTS WHEELS / DECALS SNO W THRO WER - MODEL NO . 1130STE XP (HU1130STC), PR ODUCT NO . 954 22 30-81 KEY P ART NO . NO . DESCRIPTION 1 532 18 78-32 Wheel Assembly , 16", P ower Steering, LH 2 532 15 54-43 Pin, Klik 1/4 3 532 19 21-09 Cov er , P ower Steering 4 532 18 44-71 Bolt, Shoulder #10-24 x 5/8 5 873 80 05-00 Nut, Lock 5/16-1 ...
-
Husqvarna 1130STE XP - page 32
532 19 12-90 Re v . 2 07.30.04 BY Printed in U.S .A. S E C T I ON 1: L I MIT E D W A R R A N T Y Husqvarna F orest & Garden Company (“Husqvarna”) warrants Husqv arna product to the original pur- chaser to be free from defects in material and workmanship from the da te of purchase for the “Warranty P eriod” of the product as set f or th ...
¿Tienes una pregunta acerca de Husqvarna 1130STE XP?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Husqvarna 1130STE XP, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Husqvarna 1130STE XP probablemente compartirá una forma de solucionarlo.