-
Napco Security Technologies XP-400 - page 1
Using Your XP-400 Securit y System ARMED READY SYSTEM ü ZONE 1 ZONE 2 ZONE 3 ZONE 4 NAPCO Oi220a.pub page 1 Thursday, December 18, 1997 18:31 ...
-
Napco Security Technologies XP-400 - page 2
2 Oi220a.pub page 2 Thursday, December 18, 1997 18:31 ...
-
Napco Security Technologies XP-400 - page 3
Introduction Congratulations on your purchase of an advanced NAPCO EXPRESS XP-400 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been de ...
-
Napco Security Technologies XP-400 - page 4
4 1 Bell / Battery Test Test your bell or siren by pressing A followed by 1 . This will cause the bell, or siren to sound for 2 seconds and also initiate a test of the battery . 2 Central Station Communication Test (This test should only be performed on weekends or at a time designated by your alarm company) 1. Notify Central Station of the impendi ...
-
Napco Security Technologies XP-400 - page 5
ARMED READY SYSTEM ü ZONE 1 ZONE 2 ZONE 3 ZONE 4 Keypad Controls and Indicators Ready Light will light when all zones are secure and system is ready to be Armed. Zone Lights ( 1 through 4) will light to indicate that the corresponding Zone is open, and will flash to indicate a zone in alarm. Armed Light will light when system is Armed, and will fl ...
-
Napco Security Technologies XP-400 - page 6
Arming Your System When Leaving 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your prot- ective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure these zones before proceeding. If any zones cannot be secured, see Bypassing zones below. 2 Enter your user code. Th ...
-
Napco Security Technologies XP-400 - page 7
Protecting Yourself While at Home 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure those zones before proceeding. 2 Enter your user code. The Green Ready light will go out, and the red Armed light wi ...
-
Napco Security Technologies XP-400 - page 8
Emergency Buttons The two sets of emergency buttons, if programmed, are always active whether the system is armed or disarmed. Discuss these buttons with your installer. The emergency signal will only be activated when the two respective buttons are pressed at the same time. Auxiliary Alarm: Simultaneously press f + F to alert the central station o ...
-
Napco Security Technologies XP-400 - page 9
Disarming Your System when Returning 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. 2 Enter your user code. The Red Armed light will go out, indicating that the system has been disarmed. Note: If you make a mistake entering your code, pr ...
-
Napco Security Technologies XP-400 - page 10
Special Functions A By pressing A followed by the appropriate key, (do not press simultaneously) these special functions and features can be enabled: A0 Easy Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by pressing a followed by 0 . This will allow the easy arming of the system by someone who is not a regular sys ...
-
Napco Security Technologies XP-400 - page 11
Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where you can program and/or reprogram up to 4 User Codes. The following explains how you will use this code to program or erase additional user codes. Entering the User Program Mode Press A followed by 8 and t ...
-
Napco Security Technologies XP-400 - page 12
The XP400 is constantly monitoring its own components, as well as all critical services, such as AC Power and the Telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the Yellow ü ü SYSTEM light and beeping the keypad buzzer. If you ...
-
Napco Security Technologies XP-400 - page 13
13 ü ü System Troubles Keypad Beeps or ü ü SYSTEM Flashes Zone light ON System Trouble Condition Action 2 Beeps 1 Bell / Siren Trouble There is a problem with the Bell or Siren. Call installing com- pany for service. 2 Beeps 3 Wireless Receiver Trouble A problem has been detected with the wireless receiver. Call installing company for service. ...
-
Napco Security Technologies XP-400 - page 14
Ambush Code - In the event that you are forced by an intruder to dis- arm your system, this special code can be used to disarm the system, and simultaneously send a silent alarm to Central Station. If your sys- tem has the Ambush feature enabled, the code assigned as the User 4 code will function as your Ambush Code Arming / Disarming - Turning the ...
-
Napco Security Technologies XP-400 - page 15
15 Notes Oi220a.pub page 15 Thursday, December 18, 1997 18:31 ...
-
Napco Security Technologies XP-400 - page 16
NAPCO LIMITED WARRANTY THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with ...
¿Tienes una pregunta acerca de Napco Security Technologies XP-400?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Napco Security Technologies XP-400, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Napco Security Technologies XP-400 probablemente compartirá una forma de solucionarlo.