-
Uni-T UT325 - page 1
T able of Contents 4 7 8 10 12 16 16 17 17 18 18 18 19 19 19 20 21 Title Page Safety Information Getting Started Components Display Elements Buttons Using the Thermometer Changing Setup Options Entering and Exiting Setup Changing the Logging Interval Changing the Thermocouple T ype Changing the Offset (T1) Changing the Offset (T2) Sleep Mode Changi ...
-
Uni-T UT325 - page 2
23 23 24 25 25 26 26 26 26 27 27 27 28 29 29 30 31 31 Title Page Measuring T emperatures Connecting a Thermocouple Displaying T emperatures Holding the Displayed T emperatures T urning on and off of display backlight Viewing the MIN, MAX, and A VG Readings Using the Offset to Adjust Probe Errors Over Limit Alarm Over Limit Signal Output Debug Using ...
-
Uni-T UT325 - page 3
Maintenance Replacing the Battery Cleaning the Case Specifications Environmental General Electrical Title Page 32 32 32 33 33 33 33 Model UT321/322/323/325: OPERA TING MANUAL 3 ...
-
Uni-T UT325 - page 4
Safety Information The Uni-T rend Model UT321, UT322, UT323 and UT325 Thermometers (‘the thermometer) are microprocessor-based, digital thermometers designed to use external J-, K-, T -, E-, R-, S- and N- type thermocouples (temperature probes) as temperature sensors. UT321: T1, suitable for K-, J-, T - and E- type thermocouples UT322: T1 and T2, ...
-
Uni-T UT325 - page 5
Refer to safety information in T able 1 and the international symbols in T able 2. T able 1. Safety Information Before using the thermometer inspect the case. Do not use the thermometer if it appears damaged. Look for cracks or missing plastic. Pay particular attention to the insulation around the connectors. Disconnect the thermocouple(s) from the ...
-
Uni-T UT325 - page 6
Caution A caution identifies conditions and actions that may damage the meter or the equipment under test. Use the proper thermocouples, function, and the range of your thermometer . When carrying two thermocouples measurement, make sure there are no potential differences between two thermocouples. Do not attempt to recharge the battery . Match the ...
-
Uni-T UT325 - page 7
Getting Started Everything in this Users Manual applies to all Models of UT321, UT322, UT323 and UT325 unless otherwise indicated. T o become familiar with the thermometer , study the following: Figure 1 and T able 3 describe the components Figure 2 and T able 4 describe the display . Figure 3-a and 3-b and T able 5 describes the functions of the b ...
-
Uni-T UT325 - page 8
Figure 1. Components Model UT321/322/323/325: OPERA TING MANUAL 8 ...
-
Uni-T UT325 - page 9
T able 3. Components Display Buttons Thermocouple T1 input Thermocouple T2 input (UT323 and UT325 only) USB Port SIGN Port - Over Limit Signal Output (UT323 and UT325 only) NTC Battery Door 9V battery (6F22 ) 1 2 3 4 5 6 7 8 9 Model UT321/322/323/325: OPERA TING MANUAL 9 ...
-
Uni-T UT325 - page 10
Model UT321/322/323/325: OPERA TING MANUAL 10 ...
-
Uni-T UT325 - page 11
T able 4. Display Elements Setup is in progress when the icon blinks Display readings of maximum, minimum and average Data T ransferring is in progress Logged readings are displayed when the icon blinks Low battery . Replace the battery The thermocouple type The temperature units Secondary Display 1 Under Calibration mode when the icon blinks. The ...
-
Uni-T UT325 - page 12
Figure 3-a UT321 and UT323 buttons set Model UT321/322/323/325: OPERA TING MANUAL 12 ...
-
Uni-T UT325 - page 13
Figure 3-b UT322 and UT325 button set Model UT321/322/323/325: OPERA TING MANUAL 13 ...
-
Uni-T UT325 - page 14
T able 5. Buttons Press to turn the thermometer on or off Press to turn the display backlight on and off. Press to freeze or unfreeze the displayed readings Press to switch between Celsius (ºC), Fahrenheit(ºF), and Kelvin (K) Press to step through the maximum, minimum, and average readings. Press and hold to turn off this display . Press to step ...
-
Uni-T UT325 - page 15
Press to start or exit Setup. Press to scroll the Setup option you want to change (See “Changing Setup Options”) After entering the Setup mode, press to increase the displayed setting. (See “Changing Setup Options”) After entering the Setup mode, press to decrease the displayed setting. (See “Changing Setup Options”) Confirm button. (Se ...
-
Uni-T UT325 - page 16
Using the Thermometer 1) Plug the thermocouple(s) into the input connector(s). 2) Press the power button to turn on the thermometer . 3) Set the type of thermocouple(s) to be same of the type plug into the input connector(s). If no thermocouple is plugged into the selected input or the thermocouple is “open” and the over-range positive deviatio ...
-
Uni-T UT325 - page 17
When the thermometer is in Setup mode, the display shows and blinks SETUP . Press SETUP to start or exit Setup. Press SETUP to scroll the Setup option you want to change after The logging interval determines how often the thermocouple stores logged readings in memory . Y ou choose the length of the logging interval. See “Using Memory”. Press SE ...
-
Uni-T UT325 - page 18
1. Press SETUP until the display shows TYPE. 2. Press or to select the thermocouple type you want including K-, J-, E- type (UT323 and UT325 have extra R-, S- and N- type). 1. Press SETUP until the display shows OFFSET and T1 2. Press or until the display shows the correct reading. The offset readings range 1. Press SETUP until the display shows OF ...
-
Uni-T UT325 - page 19
Model UT321/322/323/325: OPERA TING MANUAL 19 ...
-
Uni-T UT325 - page 20
Model UT321/322/323/325: OPERA TING MANUAL 20 ...
-
Uni-T UT325 - page 21
Below table shows the measuring range of each type of thermocouple K type: -200.0ºC to +1372ºC (-328.0 ºF to +2501 ºF) J type: -210.0ºC to +1200ºC (-346.0 ºF to +2192 ºF) T type: -250.0ºC to +400.0ºC (-418.0 ºF to +752.0 ºF) E type: -150.0ºC to +1000ºC (-238.0 ºF to +1832 ºF) Model UT321/322/323/325: OPERA TING MANUAL 21 ...
-
Uni-T UT325 - page 22
For example: The maximum reading of the high alarm of K type is +1372ºC. The minimum reading of the high alarm of K type is either the low alarm reading plus 1 or -200ºC. Below table shows the measuring range of each type of thermocouple K type: -200.0ºC to +1372ºC (-328.0ºF to +2501ºF) J type: -210.0ºC to +1200ºC (-346.0ºF to +2192ºF) T ...
-
Uni-T UT325 - page 23
Model UT321/322/323/325: OPERA TING MANUAL 23 ...
-
Uni-T UT325 - page 24
Model UT321/322/323/325: OPERA TING MANUAL 24 ...
-
Uni-T UT325 - page 25
Measuring T emperatures Thermocouples are colour coded by type based on the North American ANSI Colour Code: T ype Colour T ype Colour J Black R Green K Y ellow S Green T Blue N Orange E Purple 1. Plug a thermocouple into the input connector(s). 2. Set the thermometer for the correct thermocouple type. T o change the thermocouple type, see “Chang ...
-
Uni-T UT325 - page 26
1. Press ºC ºFK to select the correct temperature scale. 2. Hold or attach the thermocouple(s) to the measurement location. The temperature reading appears in the selected display 1. Press HOLD to freeze the readings on the display . The display shows HOLD. 2. Press HOLD again to turn off the HOLD function. 1. Under temperature measurement mode, ...
-
Uni-T UT325 - page 27
Use the offset option in Setup to adjust the thermometer’s readings to compensate for the errors of a specific thermocouple. 1. Plug the thermocouple into the input connector . 2. Place the thermocouple in a known, stable temperature environment (such as an ice bath or a dry well calibrator). 3. Allow the readings to stabilize. 4. In Setup change ...
-
Uni-T UT325 - page 28
After entering the Debug mode, you can self-debug. Below is the procedure: K- and J- type: -180ºC, 0ºC and 900ºC T type: -180ºC, 0ºC and 400ºC E type: -140ºC, 0ºC and 900ºC R- and S- type: 0ºC and 1200ºC N type: -180ºC, 0ºC and 1200ºC Remark: 0ºC only need to debug k type. Model UT321/322/323/325: OPERA TING MANUAL 28 ...
-
Uni-T UT325 - page 29
Remark: The corresponding table between temperature and voltage refer to BS EN 60584- 1:1996. Before carrying out debug, to ensure your standard source has enough accuracy . It is at your own responsibility , if the thermometer has too big accuracy deviation is caused by the standard source does not have enough accuracy . Using Memory During a logg ...
-
Uni-T UT325 - page 30
display 1 shows the logged reading. Each presses of ENTER will automatically store the logged readings in the next memory location. Press or could change the memory location, the empty location shows “- - - - - ”. 5. If you selected an auto logging interval, set the logging interval not 00:00. After entering logging mode, the secondary display ...
-
Uni-T UT325 - page 31
1. Press STORE to enter logging mode, the display shows DA T A and blinks. 2. Press and hold down STORE 2 seconds, the display shows CLR. 3. Press ENTER to delete all the logged readings from memory . It is not possible to delete the logged readings one by one. The display then shows “----“ Communicating with a PC Y ou can transfer the contents ...
-
Uni-T UT325 - page 32
Maintenance Replace the batteries as soon as the battery indicator appears. The possibility of false readings can lead to personal injury . 1. T urn off the thermometer . 2. Loosen the screw and remove the battery door . 3. Replace 1 piece of 9V battery (6F22). Replace the battery door and tighten the screw . Use soap and water or mild commercial c ...
-
Uni-T UT325 - page 33
Specifications Operating T emperature Storage T emperature Humidity -10ºC to 50ºC (14ºF to 122ºF) -40ºC to + 60ºC (-14ºC to +140ºC) Non condensing <10ºC (<50ºF) 95% RH: 10ºC to 30ºC (50¨ºF to 86ºF) 75% RH: 30ºC to 40ºC (86ºF to 104ºF) 45% RH: 40ºC to 50ºC (104ºF to 122ºF) Certification Safety EN61326: 2006, EN55022: 200 ...
-
Uni-T UT325 - page 34
Function UT321 UT322 UT323 UT325 Input Protection T ype Input Measurement Range Display Resolution Measurement Accuracy K, J, T , E K, J, T , E, R, S, N T1 T1, T2 T1 T1, T2 K type: -200.0ºC to +1372ºC (-328.0 ºF to +2501 ºF) J type: -210.0ºC to +1200ºC (-346.0 ºF to +2192 ºF) T type: -250 ºC to +40 0.0º C ( -418 ºF to +7 52.0 ºF ) E typ ...
-
Uni-T UT325 - page 35
Function UT321 UT322 UT323 UT325 Input Protection Measurement Accuracy 30V Below -10ºC: add 0.5ºC Below -200ºC, add +2ºC T ype T Below -200ºC: for reference only . 50 times per second, Updates 2-3 times per second Relative T ime 0 ~ 99 sets Logging Interval, Thermocouple T ype, Offset (T1), Offset (T2) (UT322 and UT325 only), Sleep Mode, Line ...
-
Uni-T UT325 - page 36
** END ** Accuracy is specified for ambient temperatures between 18ºC(60ºF)and 28ºC (82ºF) for a period of 1 year , operating temperatures: -10ºC ~ 50ºC (14ºF ~122ºF). The above specifications do not include thermocouple error ,probe tolerance is not included in above technical index. Model UT321/322/323/325: OPERA TING MANUAL 36 ...
-
Uni-T UT325 - page 37
Copyright 2008 Uni-T rend Group Limited. All rights reserved. Manufacturer: Uni-T rend T echnology (Dongguan) Limited Dong Fang Da Dao Bei Shan Dong Fang Industrial Development District Hu Men T own, Dongguan City Guang Dong Province China Postal Code: 523 925 Headquarters: Uni-T rend Group Limited Rm901, 9/F , Nanyang Plaza 57 Hung T o Road Kwun T ...
¿Tienes una pregunta acerca de Uni-T UT325?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Uni-T UT325, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Uni-T UT325 probablemente compartirá una forma de solucionarlo.