Español dropdown-ico

Manual de instrucciones Sharp PG-F320W

34 de páginas 1.63 mb
Descargar

Pasar a la página of 34

Summary
  • Sharp PG-F320W - page 1

    MODEL PG-F320W DA TA PR OJECT OR SETUP MANU AL Connecting Pin Assignments ............................ 2 RS-232C Specifications and Commands .......... 4 Setting up the Projector Netw ork En vironment ... 9 1. Connecting the Projector to a Computer .......... 10 2. Setting an IP Address f or the Computer .......... 11 3. Setting up a Network Connec ...

  • Sharp PG-F320W - page 2

    -2 Connecting Pin Assignments COMPUTER Input/Output Pin No. Signal 1. Video input (r ed) 2. Video input (green/sync on gr een) 3. Video input (blue) 4. Not connected 5. Not connected 6. Earth (red) 7. Earth (green/sync on green) 8. Earth (blue) 9. Not connected 10. GND 11. Not connected 12. Bi-directional data 13. Horizontal sync signal: TTL level ...

  • Sharp PG-F320W - page 3

    -3 Connecting Pin Assignments RS-232C T erminal : mini DIN 9 pin f emale connector RD SD SG RS CS Signal Name 8 9 6 5 21 4 3 7 Pin No. 1. 2. 3. 4. 5. 6. 7. 8. 9. I/O Reference Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to CS in internal circuit Connec ...

  • Sharp PG-F320W - page 4

    -4 Computer contr ol A computer can be used to control the pr ojector by connecting an RS-232C serial control cable (cr oss type, commerciall y availab le) to the projector . (See page 24 of the projector’ s operation manual f or connection.) Communication conditions Set the serial port settings of the computer to match that of the table. Signal ...

  • Sharp PG-F320W - page 5

    -5 Commands Example: When turning on the projector , make the following setting. → ← PO W R _ 1 __ OK Projector Computer Computer DVI Normal Stretch Dot By Dot Full Area Zoom V-Stretch Normal Stretch Dot By Dot Full Area Zoom V-Stretch CONTROL CONTENTS Power ON Standby mode (or 30-second startup time) COMMAND PARAMETER RETURN Power Projector Co ...

  • Sharp PG-F320W - page 6

    -6 OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or E ...

  • Sharp PG-F320W - page 7

    -7 RS-232C Specifications and Commands OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR O ...

  • Sharp PG-F320W - page 8

    -8 RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (or 30-second startup time) COMMAND PARAMETER RETURN Image Shift OSD Display Video System Background Lamp Setting Auto Sync Auto Power Off Auto Restart STANDBY Mode Auto Keystone PRJ Mode Language Setup Guide System Sound Internal Speaker RGB Frequency Check Fan Mode Lamp ...

  • Sharp PG-F320W - page 9

    -9 Pag e 1 0 1. Connecting the pr ojector to a computer Setting up the Projector Network Environment This section describes the basic procedure f or using the projector via the network. If the network is alread y constructed, the projector’ s network settings ma y need to be changed. Please consult your netw ork administrator for assistance with ...

  • Sharp PG-F320W - page 10

    -10 Setting up the Pr ojector Network En vironment 1. Connecting the Pro- jector to a Computer Establishing a one-to-one connection fr om the projector to a computer . Using a LAN cab le (Category 5, cross-o ver type) you can config- ure the projector via the computer . 1 Disconnect the computer’ s LAN cable fr om the existing netw ork. 2 Connect ...

  • Sharp PG-F320W - page 11

    -11 Setting up the Projector Netw ork En vironment 2. Setting an IP Address for the Computer The following describes how to make settings in Windows ® XP (Professional or Home Edition). 1 Log on the network using the administrator’ s account for the computer . 2 Click “Star t”, and clic k “Control P anel”. 3 Click “Network and Internet ...

  • Sharp PG-F320W - page 12

    -12 Setting up the Pr ojector Network En vironment 1 2 After confirming or setting, proceed to “3. Setting up Network Connection f or the Pr ojector” . 5 Click “Internet Protocol (TCP/IP)”, and click the “Properties” button. 6 Confirm or change an IP address f or the setup computer . 1 Confirm and note the current IP ad- dress, Subnet m ...

  • Sharp PG-F320W - page 13

    -13 Setting up the Projector Netw ork En vironment 3. Setting up a Network Connection for the Projector Settings for suc h items as the projector’ s IP address and subnet mask are compatible with the existing netw ork. Set each item on the pr ojector as follows. (See page 50 of the projector’ s operation manual f or setting.) DHCP Client : Off ...

  • Sharp PG-F320W - page 14

    -14 4 The TCP/IP setting screen ap- pears, ready for network settings f or the projector . Note • Confirm the existing network’ s segment (IP address group) to avoid setting an IP ad- dress that duplicates the IP addresses of other network equipment or computers. If “192.168.150.2” is not used in the network having an IP address of “192.1 ...

  • Sharp PG-F320W - page 15

    -15 Controlling the Projector via LAN Controlling the Projector Using Internet Explorer (Version 5.0 o r later) Complete connections to external equipment before starting the operation. (See pages 21- 25 of the projector’ s operation manual.) Complete the A C cord connection. (See page 25 of the projector’ s operation manual.) Note • When con ...

  • Sharp PG-F320W - page 16

    -16 Confirming the Projector Status (Status) On this screen, you can confirm the projector status. Y ou can confirm the following items : • • • • • MA C Address • • • • • Power • • • • • Condition • • • • • Lamp Timer • • • • • Lamp Life • • • • • Input • • • • • Signal Info • ...

  • Sharp PG-F320W - page 17

    -17 Contr olling the Projector via LAN Setting and Adjusting the Projector (Settings & Adjustments ) Example: “Picture” screen display for COMPUTER On these screens, you can make pr ojector settings or adjust ments. Y ou can set or adjust the follo wing items : • • • • • Picture Mode • • • • • CLR T emp • • • • ? ...

  • Sharp PG-F320W - page 18

    -18 Contr olling the Projector via LAN Making General Settings for the Network (Network - General) On this screen, you can make general settings relating to the network. After clic king the “Apply” button, the set val- ues appear . Confirm that the values are set properl y , and then clic k the “Confirm” but- ton. Note • After setting ite ...

  • Sharp PG-F320W - page 19

    -19 Contr olling the Projector via LAN Set ting Error Items and Destination Addresses to which E - m ail is to be Sent when an Error Occurs (Mail – Recipient Settings) On this screen, you can input e-mail destina- tions to which err or notification (error items) e-mails are sent. Note • E-mail Address can be up to 64 characters. • Y ou can in ...

  • Sharp PG-F320W - page 20

    -20 Setting up the Pr ojector Using RS-232C or T elnet When Connecting Using RS-232C 1 Launch general purpose terminal emulator . 2 Input settings for the RS-232C port of the terminal em ulator as follows. Baud Rate : 9600 bps* Data Length : 8 bit Parity Bit : None Stop Bit : 1 bit Flow Control : None * This is the f actor y default setting. If the ...

  • Sharp PG-F320W - page 21

    -21 Setting up the Pr ojector Using RS-232C or T elnet When Connecting Using Telnet 1 Click “Star t” from the Windows ® desk- top and select “Run”. 2 Enter “telnet 192.168.150.2” in the text box that opens up. (If the IP address of the projector is 192.168.150.2.) 3 Click the “OK” button. 4 “User Name:” is displayed. Input the ...

  • Sharp PG-F320W - page 22

    -22 Setting up the Pr ojector Using RS-232C or T elnet SETUP MENU (Main Menu) [1] IP Address IP address settings. (P age 25 ) [2] Subnet Mask Subnet mask settings. (Page 25 ) [3] Default Gateway Def ault gatewa y settings. (Page 25 ) [4] User Name (Factory default setting : Not Re- quired) Setting of user name f or security protection. (P age 25 ) ...

  • Sharp PG-F320W - page 23

    -23 View Setting Detail List ([V]View All Setting) 1 1 1 1 1 Enter “v” and press the “Enter” key . Display all setting values(*). Enter number or symbol of item to be selected on the SETUP MENU . When setting, input the details to be set. Setting is carried out one item at a time, and sa ved at the end. ▼ SETUP MENU ---------------------- ...

  • Sharp PG-F320W - page 24

    -24 Save Settings and Quit ([S]Save & Quit) Save set values and quit menu. 1 1 1 1 1 Enter “s” and press the “Enter” key . 2 2 2 2 2 Enter “y” and press the “Enter” key . ▼ SETUP MENU ---------------------------------SETUP MENU-------------------------------- [1]IP Address [2]Subnet Mask [3]Default Gatewa y [4]User Name [5]Pas ...

  • Sharp PG-F320W - page 25

    -25 IP Address Setting ([1]IP Address) Setting of IP address. 1 1 1 1 1 Enter “1” and press the “Enter” key . 2 2 2 2 2 Enter numerical value to be set and press the “Enter” key . Display IP address after change (*). Subnet Mask Setting ([2]Subnet Mask) Setting subnet mask. 1 1 1 1 1 Enter “2” and press the “Enter” key . 2 2 2 2 ...

  • Sharp PG-F320W - page 26

    -26 Password Setting ([5]Password) Carrying out security protection using password. 1 1 1 1 1 Enter “5” and press the “Enter” key . 2 2 2 2 2 Enter passw ord and press the “Enter” key . Displa y set passw ord (*). Note • Password can be up to 8 characters. • Y ou can input the characters below : a-z, A-Z, 0-9, -, _ • In the de f a ...

  • Sharp PG-F320W - page 27

    -27 Disconnecting All Connec- tions ([D]Disconnect All) It is possible to disconnect all the TCP/IP connec- tions currently recognized b y the projector . Even if the COM Redirect port is fixed in the Busy status due to a problem, it is possible to force the Ready status back by carrying out this disconnection. 1 1 1 1 1 Enter “d” and press the ...

  • Sharp PG-F320W - page 28

    -28 Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) It is possible to confirm that a network connection between the projector and a computer etc. is work- ing normally . 1 1 1 1 1 Enter “5” and press the “Enter” key . 2 2 2 2 2 Enter IP address of device to be tested and press the “Enter” key . Display entered IP address ( ...

  • Sharp PG-F320W - page 29

    -29 Setting of Search Port (ADVANCED[0]Search Port) Sets the por t number used when searching f or the projector from the network. 1 1 1 1 1 Enter “0” and press the “Enter” key . 2 2 2 2 2 Enter numerical v alue and press the “Enter” key . Display set numerical value (*). Note • Set according to need. N o r mally , use with the f ac- ...

  • Sharp PG-F320W - page 30

    -30 1 Click “Star t” – “All Programs” – “Accessories” – “Communica- tions” – “HyperT erminal”. • If you do not ha ve HyperT er minal in- stalled, see the operation manual of y our computer . • Depending on the settings of your com- puter , you ma y be required to enter your area code and other details. Enter the inf ...

  • Sharp PG-F320W - page 31

    -31 Resetting the Lamp Timer of the Pr ojector via LAN 5 Click “Properties” on the “File” menu. 6 Click the “Settings” tab, and then c lick “ASCII Setup”. 7 Select the chec k box es next to “Send line ends with line feeds”, “Echo typed character s locally”, and “Append line feeds to in- coming line ends”, and clic k “O ...

  • Sharp PG-F320W - page 32

    -32 Comm unication cannot be established with the pr ojector When connecting the pr ojector using serial-connection Check that the RS-232C terminal of the projector and a computer or the commercially av ailable controller are connected correctly . Check that the RS-232C cab le is a cross-ov er cable. Check that the RS-232C port setting for th ...

  • Sharp PG-F320W - page 33

    -33 Tr oubleshooting Ta ke the f ollowing steps for chec king the network settings for the computer . 1. Open a command prompt (MS-DOS Prompt). • In the case of Windows ® 98 or 98SE: click “ST AR T” ➔ “Programs” ➔ “MS-DOS Prompt” in order . • In the case of Windows ® Me: click “ST ART” ➔ “Programs” ➔ “Accessor ...

  • Sharp PG-F320W - page 34

    -34 Check if the “TCP/IP” protocol is oper ating correctly using the “PING” command. Also , check if an IP address is set. 1. Open a command prompt (MS-DOS Prompt). • In the case of Windows ® 98 or 98SE: click “ST AR T” ➔ “Programs” ➔ “MS-DOS Prompt” in order . • In the case of Windows ® Me: click “ST ART” ➔ ? ...

Fabricante Sharp Categoría Home Theater System

Los documentos del dispositivo Sharp PG-F320W que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Sharp
- manuales de instrucciones PG-F320W
- hojas de producto Sharp
- folletos informativos
- o etiquetas energéticas Sharp PG-F320W
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Sharp PG-F320W.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Sharp PG-F320W, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Sharp PG-F320W. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Sharp PG-F320W.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Sharp PG-F320W, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Sharp PG-F320W. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Sharp PG-F320W.

El manual de instrucciones completo de Sharp debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Sharp PG-F320W - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Sharp PG-F320W, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Sharp PG-F320W que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Sharp PG-F320W - que deben facilitarnos los primeros pasos durante el uso de Sharp PG-F320W
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Sharp PG-F320W
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Sharp PG-F320W en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Sharp PG-F320W?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sharp PG-F320W, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sharp PG-F320W probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)