-
Clifford AvantGuard II - page 1
Owner' s Manua l World-Clas s Aut o Securit y T M Av antGu ar d I I ...
-
Clifford AvantGuard II - page 2
...
-
Clifford AvantGuard II - page 3
Table of Contents EXTREMELY IMPORTANT NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 How to Operate the Premier™ Remote Control . . . . . . . . . . . . . . . . . . 3 How to Disarm the System with the Remote Control . . . . . . . . . . . . . . . ...
-
Clifford AvantGuard II - page 4
EXTREME LY IMPORTANT NOTICE If the AvantGuard II’s control unit is removed from the vehicle for any reason, the supplied RED jumper wire MUST BE CONNECTED to pins #8 and #11 of the PIGTAIL connecto r . WARNING 1. The AvantGuard II is designed to be used only on a gasoline-powered, fuel-injected vehicle with automatic transmission. If attempts are ...
-
Clifford AvantGuard II - page 5
How to Operate the Premier™ 4x8 Remote Control The Premier 4-button/8-channel, 4-billion code remote control provides incredibly high digital code security to give you the ultimate in protection against professional thieves using digital code scanners. Even a thief equipped with the most sophisti - cated scanning device would need more then 19 ye ...
-
Clifford AvantGuard II - page 6
How to Arm the System with the Remote Control 1. Press remote control button I/channel 1. 2. Simultaneousl y , several actions will take place to confirm remote disarming: • The siren will chirp twice providing audible confirmation from a distance. (If you prefe r, you can turn off the chirp acknowledgements (see page 7 for details). • The park ...
-
Clifford AvantGuard II - page 7
Valet Mode Whenever your vehicle is to be serviced, washed or valet parked, you must use the valet mode to disarm the system and override its Smart AutoArming feature. How to Enable V alet Mode 1. Insert your key and turn the ignition to the “ON” position. 2. Flip the valet/program switch to its latched (non-momen - tary) position. 3. The LED w ...
-
Clifford AvantGuard II - page 8
Smart AutoArming™ If you forget to arm your system with the remote control, it will arm itself automat - ically 30 seconds after the vehicle doors are closed. (The Multicolor LED will blink green for visual confirmation of the 30-second Smart AutoArming countdown). If you re-open any door(s) within the 30-second countdown, the AutoArming process ...
-
Clifford AvantGuard II - page 9
Prior Intrusion Attempt Alert If the alarm sounded while you were awa y , when you remotely disarm the system will issue three chirps and three flashes of the parking lights. You’ll note that the Multicolor LED will blink in red 1-7 times, pause for one second then repeat the cycle four more time. Count the number of red blinks in any one of the ...
-
Clifford AvantGuard II - page 10
b. To turn the chirps on : Flick the switch to its latched position, then back to center . c. Y ou will hear 3 chirps to confirm chirp muting or restoration. 7. Turn the ignition off . Y ou will hear 3 chirps to confirm exiting of program mode. One-Cycle Chirp Muting: This is particularly useful when parking in a quiet residential area. Just rapidl ...
-
Clifford AvantGuard II - page 11
Remote Engine Starting How to Remotely Start the Engine Remote control button II (channel 2) will remotely start (or shut down) the engine: 1. With the remote control microswitch in the up position, press and hold button II (channel 2) until you see your vehicle’s parking lights flash twice. (NOTE: A single flash indicates a fault condition, e.g. ...
-
Clifford AvantGuard II - page 12
How to Engage AutoStart 1. Make sure that the gas tank is at least half full. To conserve battery powe r , make sure the air conditione r, radio and all other accessories are turned off. 2. Insert your ignition key and turn the switch to the “ ON ” position. 3. Within 10 seconds, press and hold the valet/program switch to its momentary position ...
-
Clifford AvantGuard II - page 13
How to Program Your AvantGuard II NOTE: A Quick Programming Guide is on pages 17-19. However, if you are programming the system for the first time, we strongly recommend that you follow the detailed instructions in the specific sections that follow before attempting to use the guide. F or your convenience, everything was preprogrammed for you at th ...
-
Clifford AvantGuard II - page 14
How to Set Your Own Personalized Siren Sound Y ou can program a unique code of siren chirps to recognize your system at a distance.. Y our Personalized Siren Sound will consist of any combination of eight or less dot (short) and/or dash (long) siren pulsating sounds. A dot is a 1/4-second siren chirp. A dash is a 3/4-second chirp. A short pause of ...
-
Clifford AvantGuard II - page 15
How to Adjust Sensitivity of the Optional OmniSensor You can easily increase or decrease the sensitivity of the optional OmniSensor any time, any place, without tools and without even knowing where to sensor is mounted. To change sensitivity of the optional OmniSenso r, use the following procedure: 1. Turn ignition to the ON position. 2. Within 10 ...
-
Clifford AvantGuard II - page 16
How to Enable/Disable AutoLock and AutoUnLock The system automatically locks your car doors 5 seconds after you shift the trans - mission into Drive. Conversel y , the doors automatically unlock after you turn the ignition off. To disable or re-enable this feature, use the following procedure: 1. Turn ignition to the ON position. 2. Within 10 secon ...
-
Clifford AvantGuard II - page 17
How to Set the Smart AutoArming Entry Delay Entry delay is programmable from 1 to 59 seconds (factory preset to 15 seconds). For security reasons, the entry delay should be just enough time for you to open the door and turn on the ignition. To set a new entry dela y , use the following procedure: 1. Turn ignition to the ON position. 2. Within 10 se ...
-
Clifford AvantGuard II - page 18
b. Flip the switch to its latched position, then back to center . You will hear 3 chirps . c. Tap the switch to its momentary position 1 time . d. Flip the switch to its latched position, then back to center . You will hear 1 chirp . e. Flip the switch to its latched position, then press button II on your remote. Y ou will hear 3 chirps to confirm ...
-
Clifford AvantGuard II - page 19
Quick Programming Guide Once you are familiar with the AvantGuard II programming procedures, you may use this quick guide to make programming changes. IMPORTANT: DO NOT use this guide unless you have programmed the AvantGuard II before. If you have never programmed the system before, you should refer first to the detailed programming instructions i ...
-
Clifford AvantGuard II - page 20
Programmable Feature Parameter Action Step Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Personalized Siren Sound Any pattern of up to 8 dots and/or dashes Flick switch to M M L C MMM L C Number of chirps 2 3 3 3 Special instructions 2 Siren duration From 1 second to 5 minutes Flick switch to M M L C M M L C L 4 C Number of chirps 2 2 1 3 Optional OmniSe ...
-
Clifford AvantGuard II - page 21
Programmable Featur e Parameter Action Step Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 AutoLock and AutoUnLock Enable Flick switch to M L C M M L C L C Number of chirps 1 2 3 Disable Flick switch to M L C M M L C M Number of chirps 1 2 3 AutoStart Enable Flick switch to M L C M L C M C Number of chirps 1 1 3 3 Special instructions 12 13 70-243C/80-121 ...
¿Tienes una pregunta acerca de Clifford AvantGuard II?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Clifford AvantGuard II, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Clifford AvantGuard II probablemente compartirá una forma de solucionarlo.