-
Chicago Electric 92956 - page 1
3/8” CLOSE QUARTER DRILL Model 92956 OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www .harborfreight.com TO PREVENT SERIOUS INJUR Y , READ AND UNDERST AND ALL W ARNINGS AND INSTRUCTIONS BEFORE USE. Copyright 2005 by Harbor F reight T ools ® . All r ights reser ved. No por tion of this manu ...
-
Chicago Electric 92956 - page 2
PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual f or the saf ety war nings and precautions, assemb ly , operating, inspection, maintenance and cleaning procedures, par ts list and assemb ly diagram. K eep your in voice with this manual. Write the inv oice number on the inside of the front cov e r . K eep this manual and inv o ...
-
Chicago Electric 92956 - page 3
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. 2. Do not operate power tools in e xplosive atmospheres, such as in the presence of flammable liquids, gases, or dust. ...
-
Chicago Electric 92956 - page 4
10. Stay alert. W atch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating po wer tools may result in serious personal injur y . 11. Dress properl y . Do not wear loose clothing or je welry . Contain ...
-
Chicago Electric 92956 - page 5
21. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. T ag damaged tools “Do not use” until repaired. 22. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that ...
-
Chicago Electric 92956 - page 6
9. Industrial applications must f ollow OSHA requirements. 13 . W ARNING! Some dust created by po w er sanding, sa wing, g rinding, dr illing, and other construction activities, contain chemicals known (to the State of Calif or nia) to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: lead from lead-b ...
-
Chicago Electric 92956 - page 7
DOUBLE INSULA TED T OOLS: T OOLS WITH TWO PR ONG PLUGS 1. T ools mar ked “Double Insulated” do not require grounding. They ha ve a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. ...
-
Chicago Electric 92956 - page 8
1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possibl ...
-
Chicago Electric 92956 - page 9
SYMBOLOGY V ~ A xxxx/min. FIGURE D Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V olts Alternating Current Amperes No Load Revolutions Per Minute (RPM) FIGURE C SKU 92956 For technical questions please call 1-800-444-3353 P A GE 9 no RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 VOLT) NAMEPLATE AMPERES ...
-
Chicago Electric 92956 - page 10
SKU 92956 For technical questions please call 1-800-444-3353 P A GE 10 PRODUCT FEA TURES 1. Drill Chuck (3) and Chuc k Key (33): The Close Quar ter Drill is equipped with a 3/8” ke yed Drill Chuck (3) that will accept dr ill bits (not included) with a 1/16” to 3/8” shank. Installing a dr ill bit into the Dr ill Chuck requires the use of the a ...
-
Chicago Electric 92956 - page 11
SKU 92956 For technical questions please call 1-800-444-3353 P A GE 11 OPERA TING INSTRUCTIONS 2. Use the Forward/Reverse Switch (35) to select the desired rotation of the tool. (See Figure D.) 3. Insert a drill bit (not included) into the Drill Chuck (3), and secure the drill bit in the Drill Chuck with the Chuck Key (33). (See Figure D.) 4. Make ...
-
Chicago Electric 92956 - page 12
SKU 92956 For technical questions please call 1-800-444-3353 P AGE 12 14. When you ha ve drilled the hole, remov e the dr ill bit from the hole while the Drill Chuck (3) is still rotating. This prev ents the drill bit from getting caught in the hole and causing damage. 15. Release pressure on the T rigger (30) to stop the Dr ill. (See Figure D.) 16 ...
-
Chicago Electric 92956 - page 13
SKU 92956 For technical questions please call 1-800-444-3353 P AGE 13 5. CA UTION! All maintenance, ser vice, or repairs not listed in this man ual are only to be attempted by a qualified service technician. CARBON BRUSH (19) CARBON BRUSH (19) FIGURE E PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUT OR HAS PRO VIDED THE P ...
-
Chicago Electric 92956 - page 14
ASSEMBL Y DIA GRAM SKU 92956 For technical questions please call 1-800-444-3353 P A GE 14 NOTE: Some parts are listed and shown for assemb ly purposes only , and are not av ailable individually as replacement parts. 33: CHUCK KEY NOT SHOWN. 34 35 ...
¿Tienes una pregunta acerca de Chicago Electric 92956?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Chicago Electric 92956, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Chicago Electric 92956 probablemente compartirá una forma de solucionarlo.