-
EverFocus EHD525EX - page 1
EVERFOCUS 1/3” Sony ExV iew Day/Night Rugged Dome Color Camera Operation Instructions Model No. EHD525EX Please read this manual first for correct install ation and op eration. This manual should be re tained for future reference. The information in th is manual was current when published. The manufacturer reserves the right to revise and impr ov ...
-
EverFocus EHD525EX - page 2
1 7. Do not operate the camera beyond the sp ecified temperature, humidity or power source ratings. Use the camera at temperatures within -40 ℃ ~ 50 ℃ (-40 ℉ ~ 122℉) and humidity between 20%~ 80%. The input power source is 12VDC/24V AC. PREF ACE The most technically advanced EHD s eries are the newest vandal-resistant Color Rugged Dome Came ...
-
EverFocus EHD525EX - page 3
2 z Conduit x 1 z Power & V ideo Cable x 1 z Desiccant Pack x 1 z Manual x 1 Optional Accessory z W all Mount Bracket (BA-EHD) SPECIFICA TIONS Pickup Device 1/3'' SONY EXView CCD Video Format NTSC or PAL Scanning System NTSC: 525 TV lines, 60 fields/sec PAL: 625 TV lines, 50 fields/sec Picture Elements 768 x 494(NTSC) ; 752 x 582(PAL) ...
-
EverFocus EHD525EX - page 4
3 Power Source 12VDC/24VAC Power Consumption 24VAC: 6VA max. (Heater OFF) 24VAC: 20.5VA max. (Heater ON) 12VDC: 4W max. (Heater OFF) 12VDC: 11.5W max. (Heater ON) Dime nsions 130mm(W) x 98.8mm(H) x 130mm(D); 5.1"(W) x 3.9"(H) x 5.1"(D) Weight 1.7kg ; 3.7lbs Operating Temperature -40°C~50°C ;- 40°F~122°F (20%~80% Hu midity) Certif ...
-
EverFocus EHD525EX - page 5
4 2. Remove the camera. T o remove the camera, first unplug the wire connection on the b ack of the camera. Then loosen the 2 locking scr ews on the camera base, push the camera base to the right (toward heater direction, as shown in Figure 3), r emo ve th e c am er a f ro m t he mou nt in g b as e. Reinstall the camera and the cable while the base ...
-
EverFocus EHD525EX - page 6
5 Attach the base to the w all or ceiling, fix the base by the 4 setscrew s attached in the accessory pack. The dome is weighted 1.7kg, please make sure if the mounting is strengthened enough to support it, if not, please reinforce the mounting according to the environ ment. Note : Th e diameter of the screw hole is ψ 4.7mm. Caution: T o prevent m ...
-
EverFocus EHD525EX - page 7
6 4. Re-assemble Camera 1. When mounting COLOR RUG GED DOME CAM ERA on the wall, please aim the “ Wa l l ” in line with the triangle “ S ” marked on the lead frame. (Factory default) 2. When mounting COLOR RUG GED DOME CAM ERA on the ceiling, please aim the “ Ceiling ” in lin e with the triangle “ S ” marked on the lead frame. 6 Fig ...
-
EverFocus EHD525EX - page 8
7 5. W ire Connection Connect the power supply cable (24V AC/12VDC), video output and alar m output to the proper connectors shown as Figure 7. The V. Phase adjustment screw is located on the termination board. The vertical phase may require adjustment to synchronize the ve rtical phase of the camera with other camera in the system when it is to be ...
-
EverFocus EHD525EX - page 9
8 syn c mod e. Make th e adju st men t w hen t he v er tic al p has e of the c a mera do es not match with other cameras. 6. V iew A ngle Adjustment The camera can be rotated 360 ° horizontally , 140 ° vertically and 60 ° 3’rd axis view angles (as shown in Figure 8). Adjust the proper camera view angle as needed. If a vari-focal lens is used, ...
-
EverFocus EHD525EX - page 10
9 7. Repositioning the adjust ment stick (only for 3.6-9mm V ari-focal lens) a) The default position of adjustment stick is shown as below: b) While zooming In/Out with the adjustment stick, it may obstruct oth er adjustments of Iris Level and V ideo Output. c) In this case, y ou can gently take off the adjust ment stick and plac e it to the other ...
-
EverFocus EHD525EX - page 11
10 ...
-
EverFocus EHD525EX - page 12
11 DIP SWITCH FUNCTION LL (Line-Lock) OFF/ON To select the sync mode between Intern al Sync.(LL off) and Line-Lock (LL on). Set the line-lock off, the camera will synchronize to the in ternal time base. Set the line-lock ON, the camera’s vertical sy nchronization can be driven by the AC signal in the power lines. Note: Line-Lock sync mode operati ...
-
EverFocus EHD525EX - page 13
12 BLC (Back Light Compensation) ON/OFF When BLC is turned on, the AGC, ES and IRIS operating points are d etermined by averaging over the cent er area instead of entire field-of -view, so that a dimly-lit foreground object at center area can be clearly distinguish ed from brightly-lit backgrounds. BLC should not be u s ed unless it is needed to co ...
-
EverFocus EHD525EX - page 14
13 SIMPLE INSTRUCTIONS FO R THE DESICCANT P ACK Due to the camera lens blurred from the humidity inside the camera. The desiccant pack abso rbs the humidity ; please refer to the easy instruction as follows: 1. Adjust all settings first and place the d esic cant pack on the horizont al rod, then bend the horizontal rod and fix it. 2. Install the ou ...
-
EverFocus EHD525EX - page 15
14 EverFocus Electronics Corp. Head Office: 12F , No.79 Sec. 1 Shin-T ai W u Road, Hsi-Chih, T aipei, T aiwan TEL: +886-2-26982334 F AX: +886-2-26982380 www .everfocus.co m.tw USA L.A. Office: 1801 Highland A ve. Unit A Duarte, CA 91010, U.S.A. TEL: +1-626-844-8888 F AX: +1-626-844-8838 www .everfocus.co m USA N.Y . Office: 415 Oser A venue Unit S ...
¿Tienes una pregunta acerca de EverFocus EHD525EX?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con EverFocus EHD525EX, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con EverFocus EHD525EX probablemente compartirá una forma de solucionarlo.