-
Makita 4340FCT - page 1
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. ENGLISH Jig Sa w MODEL 4340T MODEL 4340CT MODEL 4340FCT 001905 DOUBLE INSULA TION ...
-
Makita 4340FCT - page 2
2 SPECIFICATIONS • Due to our continuing programme of research and de velopment, the specifications herein are subject to change without notice. • Note: Specifications may dif fer from country to countr y . SYMBOLS END201-2 The follo wing show the symbols used for the equipment. Be sure that you understand their meaning bef ore use. ........... ...
-
Makita 4340FCT - page 3
3 GENERAL SAFETY RULES GEA001-3 W ARNING: Read all instructions. F ailure to f ollow all instructions listed below ma y result in electric shock, fire and/or serious injur y . The term “power tool” in all of the warnings listed below ref ers to your mains-operated (corded) po wer tool or batter y- operated (cordless) pow er tool. SA VE THESE IN ...
-
Makita 4340FCT - page 4
4 19. Store idle power tools out of the reach of c hil- dren and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. P ower tools are dangerous in the hands of untrained users. 20. Maintain power tools. Chec k for misalignment or binding of moving parts, breakage of parts and any other condition that ...
-
Makita 4340FCT - page 5
5 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Selecting the cutting action This tool can be operated with an orbital or a straight line (up and do wn) cut- ting action. The orbital cutting action thrusts the blade forw ard on the cutting stroke ...
-
Makita 4340FCT - page 6
6 CA UTION: • The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function ma y no longer work . The tools equipped with electronic function are easy to operate because of the fol lo wi ng fea tu re s. Constant speed control Electronic speed control for obtaining constant spee ...
-
Makita 4340FCT - page 7
7 K eeping that situation, inser t the saw blade into the b lade clamp as far as the two protrusions of the blade can not be seen. Return the tool opener to its or iginal position. After installing, alwa ys make sure that the blade is securely held in place b y trying to pull it out. CA UTION: • Do not open the tool opener excessiv ely , or it ma ...
-
Makita 4340FCT - page 8
8 Bevel cutting CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore tilting the tool base. With the tool base tilted, you can mak e bevel cuts at an y angle between 0 ° and 45 ° (left or right). Loosen the bolt on the back of the base with the he x wrench. Move the base so that the bolt is positioned in the center of ...
-
Makita 4340FCT - page 9
9 Cutouts Cutouts can be made with either of two methods A or B. A) Boring a starting hole For internal cutouts without a lead-in cut from an edge, pre-drill a starting hole 12 mm or more in diameter . Inser t the blade into this hole to start your cut. B) Plunge cutting Y ou need not bore a starting hole or make a lead-in cut if you carefully do a ...
-
Makita 4340FCT - page 10
10 Dust extraction The dust nozzle (accessory) is recommended to perform clean cutting opera- tions. T o attach the dust nozzle on the tool, insert the hook of dust nozzle into the hole in the base. The dust nozzle can be installed on either left or right side of the base. Then connect a Makita vacuum cleaner to the dust nozzle . CA UTION: If you t ...
-
Makita 4340FCT - page 11
11 1. Straight cuts When repeatedly cutting widths of 160 mm or less, use of the rip fe nce will assure fast, clean, str aight cuts. T o install, inser t the rip fence into the rectan- gular hole on the side of the tool base with the fence guide f acing down. Slide the rip fence to the desired cutting width position, then tighten the bolt to secure ...
-
Makita 4340FCT - page 12
12 Guide rail adapter set (accessory) When cutting parallel and unif or m width or cutting straight, the use of the guide rail and the guide rail adapter will assure the production of f ast and clean cuts. T o install the guide rail adapter , inser t the rule bar into the square hole of the base as far as it goes . Secure the bolt with the hex wren ...
-
Makita 4340FCT - page 13
13 Anti-splintering device For splinter-free cuts , the anti-splintering device can be used. T o install the anti-splintering device, mo ve the tool base all the wa y forward and fit it from the back of tool base . When you use the cover plate , install the anti-splintering device onto the co ver plate. CA UTION: • The anti-splintering device can ...
-
Makita 4340FCT - page 14
Memo 14 ...
-
Makita 4340FCT - page 15
Memo 15 ...
-
Makita 4340FCT - page 16
Makita Cor poration Anjo , Aichi, Japan 884426E228 ...
¿Tienes una pregunta acerca de Makita 4340FCT?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 4340FCT, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 4340FCT probablemente compartirá una forma de solucionarlo.