-
AT&T 7610 - page 1
Part 2 © 1998 Philips Consumer Communications L.P . All rights reserved. Printed in Mexico. 848233037 Issue 1A T&T User's Manual for Cordless Answering System T elephone 7610 Fold open this manual for information about this telephone's installation and operation. Please r ead Part 1 – Important Product Information, included in this ...
-
AT&T 7610 - page 2
INST ALLA TION AC Adapter Modular W all Jack Standar d AC Outlet Power Cor d T elephone Line Cor d Plug the other end of the line cord into a modular phone jack. Make sure the plug snaps firmly in place. 6 Mount the base on the wall. (W ALL MOUNTING ONL Y) Hold the base so that the mounting knobs on the standard wall jack will fit into the holes on ...
-
AT&T 7610 - page 3
INST ALLA TION CHARGING HANDSET IN USE MEMO/REWIND FAST FWD SAVE CLOCK PLAY/ST OP VOLUME Use with other buttons to change settings. Base Antenna (extended) Recor d or play outgoing announcement. Cover T urn system on or off. Lift panel door to access featur es (see figur e at right). Audible clock; also use with CHANGE to set time/day . Adjust mess ...
-
AT&T 7610 - page 4
BA TTERIES 3 Charging the Handset Battery Pack The batteries need charging when: • The phone beeps four times when you press P . • The LOW BA TTER Y light on the handset flashes on and off. • The phone does not respond when you press P , and no lights go on. Place the handset in the base so the CHARGING light goes on. The batteries will be fu ...
-
AT&T 7610 - page 5
IN CASE OF DIFFICUL TY • Place the handset in the base, and check to make sure the CHARGING light is on. Unplug the AC adapter from the outlet, wait 15 seconds, then plug it in again. The CHARGING light should go on. W ait another 15 seconds, then pick up the handset and press P . The phone should operate properly . If it does not, try the next s ...
-
AT&T 7610 - page 6
IN CASE OF DIFFICUL TY If you have difficulty hearing messages • If messages are garbled, the recording heads may be soiled and should be cleaned. • Unplug the system from the electrical outlet. • Remove the cassette tape. • Use any good tape deck cleaning kit, and follow the manufacturer's instructions — OR — Rub the front face of ...
-
AT&T 7610 - page 7
OPERA TION Making A Call 1 Press P , and wait for the PHONE light to go on steadily . 2 When you hear a dial tone, dial the number . NOTE: Y ou might experience a slight delay befor e you hear a dial tone, as the AutoSelect featur e sear ches for a clear channel. Answering a Call If this phone is ringing and the handset is in the base, lift the han ...
-
AT&T 7610 - page 8
MEMOR Y This cordless phone can store 10 telephone numbers that you can dial just by pressing p and one of the number buttons. Additionally , the phone of fers a memory location accessed by pressing m . Storing Speed-Dial Numbers 1 Make sure the PHONE light is off. 2 Press p . 3 Enter the phone number (up to 16 digits). 4 Press p . 5 Press any numb ...
-
AT&T 7610 - page 9
8 OPERA TING RANGE This cordless telephone operates at the maximum power allowed by the Federal Communications Commission (FCC). Even so, the handset and base can communicate over only a certain distance — which can vary with the locations of the base and handset, the weather , and the construction of your home or office. When you make a call, if ...
-
AT&T 7610 - page 10
9 V olume Control Use the volume control on the side of the base to adjust the answering system volume. Slide the control up toward the back of the base to increase volume while listening to your announcement or messages, or down toward the bottom of the base to decrease volume. Recording Y our Announcement Before using this answering system, you n ...
-
AT&T 7610 - page 11
ANSWERING SYSTEM OPERA TION Ring Select Use the Ring Select switch on the back side of the base unit to select how many times the line will ring before the system answers a call. Set to 4 for four rings, or set to TS for T oll Saver . When you set the system to TS , the system answers after 4 rings when you have no new messages, and after 2 rings w ...
-
AT&T 7610 - page 12
FROM A REMOTE TOUCH TONE PHONE Remote Access Code The Remote Access Code is a 3-digit code which lets you access your answering system away from your home or of fice. The factory setting is 123 (printed under the microcassette lid on the base). Y ou can change this code to any 3-digit number between 100 and 999, except 323 and 523. Y ou can only ch ...
-
AT&T 7610 - page 13
© 1998 Philips Consumer Communications, L. P . All rights reserved. Printed in Mexico. 848233052 Issue 1 A TT Answering System 7610 Operation From a Remote T ouch T one Phone T o access you r answering system: 1 Dial your telephone numbe r . 2 When the system answers, enter your 3-digit Remot e Access Code . The system announces the number of mess ...
-
AT&T 7610 - page 14
COMMAND PRESS Play all messages 1 Play only new messages 2 Replay messages 1 after playing messages Rewind Hold down 4 ; release to pla y . Fast Forward Hol d down 6 ; release to pla y . Clear messages 3 , 3 . Stop 5 ; press 1 to pla y . Record announcement 7 , , speak after long beep, press 5 to stop. Change Remot e Access Code 9 , 9 , enter new c ...
¿Tienes una pregunta acerca de AT&T 7610?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con AT&T 7610, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con AT&T 7610 probablemente compartirá una forma de solucionarlo.