-
Epson 1640XL - page 1
Using Optional Equipment 33 Chapter 3 Using Optional Equipment There ar e three op tions a vailable for the EPSO N Expression 1640XL color scan ner: the transparency unit (B813202), the automati c document fe eder (B813212), and the IEEE 1394 FireWire scanner interface card (B808342). You can pu rchase these o ptions from your rese ller or from the ...
-
Epson 1640XL - page 2
34 Transparen cy Unit Unpacking the T ransparency Unit Make sure that a ll of the fo llowing it ems are include d in the tran sparency un it box. If any item s are miss ing or dama ged, cont act your EPSO N dealer , or contact EPSON at (562) 276-4382 (in the United States) or (905) 709-3839 (in Canada). Ke ep all the packi ng ma terial s so you can ...
-
Epson 1640XL - page 3
Using Optional Equipment 35 Removing the Shipping Screws To prevent dama ge during shi pping, two shi pping scre ws are att ached to the transp arency unit t o secure its lam p assemb ly. Yo u must remove these screws before using the t ranspare ncy unit. 1. Turn the transparency unit so the glass side faces up. 2. Use a Phillips head (cross head) ...
-
Epson 1640XL - page 4
36 Transparen cy Unit 4. Align the transpar ency unit’s pins with the h ole s in the scanner and lowe r the unit until it rests securely. 5. Insert the guide pin an d adjust pin that ca me with th e transp arency unit in to the screw holes. Ma ke sure th e adjust pin’s arrow faces directly to wards the center of th e guide pi n. 6. Place th e t ...
-
Epson 1640XL - page 5
Using Optional Equipment 37 8. Connec t the transp arency unit’s connecto r to the op tion ( ADF/TPU ) connector at the back of the scanner. Tighten the attached screws to secure the connect or. If you haven’t co nnected the sc a nner to your comp uter, see the Start Here sheet for instructio ns. Then plug the sc anner i n and turn it on. See C ...
-
Epson 1640XL - page 6
38 Transparen cy Unit Loading 35 mm film Follow th ese steps to load 35 m m positive or negati ve f ilm: 1. Place th e 35 mm filmst rip guide o n a flat surface and re move th e cover from one of the st rip holde rs. 2. Inse rt a fi lmstri p in th e ho lder face down. 3. Repl ace t he st rip hol der yo u removed in step 1. 4. Repeat steps 1 through ...
-
Epson 1640XL - page 7
Using Optional Equipment 39 5. Place the 35 mm fil mstrip guide on the document tabl e, and align it wi th t he no tch on the tran sparen cy guide a s shown . 6. Clo se th e TPU and be gin scanning. If you’r e using EPSON Sc an, set t he foll owing opt ions: ■ If you’re using Home Mode, selec t one of t he foll owing fo r the Document Ty pe o ...
-
Epson 1640XL - page 8
40 Transparen cy Unit Loading 35 mm slides Follow th ese steps to load 35 m m slides: 1. Load slid es in the 35 mm slide holder as shown. Make sure the glossy side of each slide faces down, and t he film emulsion layer faces up. 2. Posi tion the slide ho lder on the document tabl e. Align the slide h older with the not ch on the tr ans paren cy gui ...
-
Epson 1640XL - page 9
Using Optional Equipment 41 Loading 4 × 5-inc h film Follow th ese steps to load 4 × 5-inch film: 1. Place the 4 × 5-inch film guide on a flat surfa ce and remo ve the cove r from on e of the fil m holde rs. 2. Insert the film in the film holder, making sure the glossy (smooth) side of the film faces down and the film emulsion layer faces up. T ...
-
Epson 1640XL - page 10
42 Transparen cy Unit Loading 120-size or 220-si ze (medium f ormat) film Follow these ste ps to load 120-size or 220-size format film : 1. Place the 120/220-si ze film guide o n a flat surface and open the cove r for one of th e film hol ders. 2. Insert the film in the film holder, making sure the glossy (smooth) side of the film faces down, and t ...
-
Epson 1640XL - page 11
Using Optional Equipment 43 Loading non-stan dard siz ed film Follow th ese ste ps to loa d non-st andard sized fi lm: 1. Place the film dire ctly on the document table making sure the glossy (smooth) side of the fil m faces down. If the refle ctive document mat is installe d in the trans parency uni t, remove it. 2. Clo se th e TPU and be gin yo u ...
-
Epson 1640XL - page 12
44 Transparen cy Unit Scanning Reflective Documents To scan reflective document s with the transp aren cy unit installe d, insert the re flective document mat incl uded with the transparency unit. 1. Open the transparency unit. If the re’s a film guid e or tran sparen cy unit o n the document table, rem ove it. 2. Slide the mat into place an d in ...
-
Epson 1640XL - page 13
Using Optional Equipment 45 Adjusting the Transp arency Guide Scanning Angle If your scanne d image ’s edges are at a slight angle , adjus t the sca nning an gle by t urning the adjust pin. The direction and degr ee you adju st the an gle depen ds on your indiv idual scanner and the pla cement of t he docume nt to be scanned. You may want to expe ...
-
Epson 1640XL - page 14
46 Automatic Document Feeder Installing the Automatic Document Feeder Follow th e steps below to in stall th e auto matic do cument feeder on your scanner: 1. Make sure yo ur scanner is turned off and unplug t he cables. 2. Remove your scan ner’s documen t cover by grasping the back of the cover as sho wn and easi ng the cover up. 3. Attach th e ...
-
Epson 1640XL - page 15
Using Optional Equipment 47 5. Pla ce th e tw o knobs inc luded with the ADF bes ide the scan ner. 6. Align the inst alla tion screws with the holes in the ADF a nd slide to geth er as sho wn. 7. Tw ist t he knob s on to t he en ds of the s crews and ti ghten th em using th e enclos ed screwdri ver tool . 8. Attach the ADF’s connector to the scan ...
-
Epson 1640XL - page 16
48 Automatic Document Feeder 9. Peel the backing from the stopper and fr om t he pape r eje ct su ppor t provided with the A DF. Then attach the stopper a nd paper eje ct support to the scan ner as s hown. Insert the ta bs on the pa per e ject suppo rt into the slots a t the ri ght end of the document table. 10. Cl ose t he ADF . If you haven’t c ...
-
Epson 1640XL - page 17
Using Optional Equipment 49 ■ Is not bound. ■ Has no carbon coating. Follow th ese steps to load pape r: 1. Slide the right edge guides all th e way to the right. 2. Make sure th at the switch on the lo wer left corn er of the AD F is set with the switch towards the circular mark as shown. 3. Arrange your stack of originals face up. Follow the ...
-
Epson 1640XL - page 18
50 Automatic Document Feeder Insert the document un til it mee ts resista nce. If your document is large, slid e out the p aper support. 4. Slide the edge gui des to the ed ges of your paper. 5. Scan your document. If you’re using EPSO N Scan, foll ow these guide lines: ■ Selec t either Of fi ce Mo de or Professional Mode in the Mode box. ■ S ...
-
Epson 1640XL - page 19
Using Optional Equipment 51 Fixing Paper Jams If a paper ja m occurs, fo llow these s teps to clea r it: 1. Open the A DF cover to dete rmine where the pa per ja m occurred. 2. If paper is jammed in t he feeder, open th e cover on the le ft and slowl y pu ll out t he ja mme d pape r as shown. Be car eful not to pul l too har d or the paper may t ea ...
-
Epson 1640XL - page 20
52 IEEE 1394 Fi reWire Scanner Interface Card 3. If pape r jams in th e pape r ejec t posit ion, o pen th e cove r on t he righ t and sl owly pull ou t the jamme d paper as shown. 4. After re movi ng the j ammed paper, close th e ADF cover. IEEE 1394 FireWire Scanner Interface Card To use the IEEE 1394 FireWire scanner interface card (B808342), you ...
-
Epson 1640XL - page 21
Using Optional Equipment 53 Installing the Card in You r Scanner Before you begin, turn off the scanner and dis connect t h e power cord and any cables. 1. Remove th e two screws securing th e shield plate to the scanne r’s op tion al inte rfa ce slot, and the n remove the plate . Put the screws in a safe place in case you want to reinst all th e ...
¿Tienes una pregunta acerca de Epson 1640XL?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Epson 1640XL, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Epson 1640XL probablemente compartirá una forma de solucionarlo.