-
Sendai CD788 - page 1
CAR CD / MP3/WMA PLAYER RDS RECEIVER CD788 e 13 022706 ITEM CODE : 345827 CD788 ...
-
Sendai CD788 - page 2
CONTROL AND FUNCTION KEYS 16 VOLUME UP/DOWN BUTTON 4 EJECT BUTTON POWER BUTTON DISPLA Y BUTTON RESET BUTTON 18 BAND BUTTON MP3 SEARCH BUTTON TUNING UP/DOWN TRACK UP / DOWN BUTTONS PRESET STA TIONS BUTTONS (M1~M6) MENU BUTTON 11 15 12 8 9 AUTOMATICA LLY STORE / PRESET SCAN (AS/PS) BUTTON MP3-ID3-TAG INFORMATION BUTTON PANE L RELEASE BUTTON SELECT BU ...
-
Sendai CD788 - page 3
1.HANDLING COMP ACT DISCS MOISTURE CONDENSAT ION NOTES ON CDs P. 2 P. 3 P. 4 P. 1 P. 5 P. 6 P. 7 1. 2. 3. 4. 5. NOTES ON DISCS There are paste residue. Ink is sticky (P .5). Stickers that are beginning to peel away , leaving a sticky residue (P .6). Labels are attached (P .7). On a rainy day or in a very damp area, moisture may condense on the lens ...
-
Sendai CD788 - page 4
2. INSTALLATION Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requir ...
-
Sendai CD788 - page 5
DIN REAR-MOUNT (METHOD B) Installation using the screw holes on the sides of the unit. Fastening the unit to the factory radio mounting bracket. 1. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted) and tighten the screws at 2 places on each side. 2. Screw 3. Factory radio mountin ...
-
Sendai CD788 - page 6
E - 5 3. DETACHABLE CONTROL P ANEL (D.C.P .) Removing The Detachable Control Panel (D.C.P .). 1. Turn the power off 2. Press the D.C.P . release button 3. Remove the D.C.P . PANEL RELEASE BUTTON B A 2 Attaching the DCP CAUTION 1. Attach the panel at the right side first, with point B on the main unit touching point A on the D.C.P . (As shown on the ...
-
Sendai CD788 - page 7
E - 6 4. WIRING DIAGRAM FEMALE WITH MALE TERMINAL ISO CONNECTOR 4PIN+8PIN FUSE SOCKET ISO CONNECTOR FUSE 5 6 3 1 2 4 7 8 5 6 3 1 2 4 7 8 Figure 1 CONNECTOR A CONNECTOR B REAR LINE OUT L-CH R-CH RED WHITE GREY (See Figure 1) AMP AMP AMPLIFIER WIRING (SEE AMPLIFIER INSTRUCTIONS) ANTENNA EXTENDER CABLE ISO CONNECTOR WIRING CHART GROUND FUNCTION/LABEL ...
-
Sendai CD788 - page 8
2. MODE BUTTON (MODE) E - 7 Press this button to remove the control panel. 5. BASIC OPERATIONS 14. PANEL RELEASE BUTTON (REL) 1. POWER ON/OFF BUTTON ( ) Press POWER button or any other button on the front of the radio (except Open/Eject)to turn the unit on. Press POWER button again to turn the unit off. 3. MUTE BUTTON ( MUTE ) Press the mute button ...
-
Sendai CD788 - page 9
Fader Press the AUDIO SELECT button five times, then press the Volume down / up button to adjust the fader between the front and rear speakers from R12 (full rear) to F12 (full front). "C00” Represents a center fader level between the front and rear speakers. PRESS 1 PRESS 2 3 4 5 8. DISPLAY (DISP) Press DISPLAY momentarily to navigate throu ...
-
Sendai CD788 - page 10
Contrast The contrast level of the display is set at "CONTRAST 05" by default. Press the volume down/up button to adjust the contrast level from 00 to 10. Dimmer The dimmer feature of the display is set to "DIMMER High" by default. Press the volume down/up button to turn the dimmer to the Iow setting. Clock Format This option al ...
-
Sendai CD788 - page 11
Personal T ext Message Press the MENU button will see the “PTM” on the display ,this will allow the user to input his favor .greeting note on the display. The “INPUT MESSAGE” will be displayed by default. User is allowed to input max. 20 letters or symbols for the “PTM” to be displayed on the LCD. When “PTM” is displayed on the disp ...
-
Sendai CD788 - page 12
IGNITION OFF CLOCK RECALL The user can recall to display the clock time by press DISPLAY button, even when ignition is off. E - 11 GREETING NOTE There are three different greeting note displayed on LCD base on different condition. 1.When the unit is powered on, one of three greeting will display based on the time of day: Good Morning, Good Afternoo ...
-
Sendai CD788 - page 13
Manual Tuning Press the Up Tuning or Down T uning button for more than 3 seconds to move the radio frequency number up or down one step. Auto Seek Tuning Press the Up Tuning or Down T uning button for less than 3 seconds to move to next station automatically. 6. TUNER OPERATION Recall a Station Select a band (if needed). Press a preset button to se ...
-
Sendai CD788 - page 14
7. CD PLAYER OPERA TION INSERT AND EJECT CD Insert a CD label-side up with the unit turned on, and the disc will begin to play. Press the Eject button to stop CD play and eject the CD. The unit does not have to be turned on to eject the CD. PAUSE BUTTON (PA U) Press the pause button to suspend disc play. Press the pause button again to resume disc ...
-
Sendai CD788 - page 15
MP3/WMA SECTION E - 14 RDS functions - AF Alternative Frequencies - CT Clock Time - EON Enchanced other Network - PI Program identifications - PS Program service name - PTY Program Type - REG Regional Change - TA Traffic Announcement - TP Traffic program By pressing AF button < 3 seconds to select AF ON/OFF . “AF ON” or “ AF OFF” will sh ...
-
Sendai CD788 - page 16
MP3/WMA SECTION E - 15 User can store his favor PTY into the preset memory M1 to M6. After selected a PTY item, long press any one of the preset memory button can store the selected PTY . To recall the stored PTY item by switching on PTY mode then press preset memory < 3 seconds, the unit will automatically search the stored PTY station in the p ...
-
Sendai CD788 - page 17
MP3/WMA SECTION E - 16 TA Volume “18” will be displayed by default. The user now has 5 seconds to adjust by using volume up/down button from “0-40”. When TA function is activated, if a TA program is tuned in at the volume level set regardless of the volume of the other source at the time. Note: When the unit tuned into a TA program. The vol ...
-
Sendai CD788 - page 18
E - 17 9. MP3/WMA OPERATION MP3 and WMA (Windows Media Audio) music files are digital audio files that are compressed to allow more files on a single CD. This unit can play MP3/WMA directly from files contained on a CD-R/RW using the buttons on the receiver.Depending on the media type and recording method, some CD-R/RW's may be incompatible wi ...
-
Sendai CD788 - page 19
E - 18 Writing Files into a Medium When a medium containing MP3/WMA data is loaded, the unit checks all data. If the medium contains many folders or non-MP3/WMA files, MP3/WMA play will be delayed, it may take time for the unit to move to the next file, and searches may not be performed smoothly. Loading such a medium may produce loud noise and cau ...
-
Sendai CD788 - page 20
FILE/FOLDER PLAY There are three different play methods as following: Press M2 button more than 3 seconds during playing MP3/WMA disc for “intro play” all files of the current folder. Intro play should restart from the first song of the current folder , after all files in the current files have been intro-played. To disable current folder “in ...
-
Sendai CD788 - page 21
MP3/WMA FILE OR FOLDER SEARCHING (volume down/up button) During MP3 or WMA files playback, press MP3 search button (Band Button) twice LCD will display “Navigate search”, Press “Audio Select” key or press volume down/up button to enter the “Navigate search”. Press volume down/up button until LCD displayed “06”, Short Press MP3 enter ...
-
Sendai CD788 - page 22
ID3 INFORMATION DISPLAY If any MP3/WMA file recording with ID3 Tag information. The ID3 information such like Album title, Track title, Artist Title will be displayed and automatic scrolling through the LCD while the file is playing. User also allows pressing the AS/PS button repeatedly to view the ID3 tag information manually. E - 21 ICON DESCRIPT ...
-
Sendai CD788 - page 23
E - 22 GENERAL AM/MW Power Supply Polarity Speaker impedance Power Output Frequency Range Intermediate Frequency Usable Sensitivity Stereo Separation S/N Ratio DC 11 -14V Negative Ground 4 ohms 4 x 40W 87.5-108 Mhz 10.7 MHz Better than 15dB at S/N 30 dB 25 dB at 1KHz 50 dB 10.SPECIFICATIONS CD PLAYER REMARK : Specifications subject to change withou ...
-
Sendai CD788 - page 24
ERROR 1 ERROR 2 ERROR 3 No File Disc Error Mechanism Error Servo Focus Error Servo T racking Error No file Format supports for Playback on the disc Maybe disc dirty / disc scratched /disc upside down. Press the reset button to correct the problem. If the error code does not disappear , consult your nearest service dealer . Replace the disc. Replace ...
¿Tienes una pregunta acerca de Sendai CD788?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sendai CD788, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sendai CD788 probablemente compartirá una forma de solucionarlo.