-
Kenwood KDC-5019 - page 1
KDC-519 KDC-5019 © B64-2148-00 (K) CD-RECEIVER INSTR UCTION MANU AL AMPLI-TUNER LECTEUR DE CD MODE D’EMPLOI REPRODUCT OR DE DISCOS COMP A CT OS RECEPT OR DE FM/AM MANU AL DE INSTR UCCIONES T ake the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from ...
-
Kenwood KDC-5019 - page 2
— 2 — English Contents Wa rning .......................................3 Safety precautions ......................4 About CDs ...................................6 General features .........................7 Power Selecting the Source V olume Attenuator Loudness System Q Audio Control Speaker Setting Switching Display Switching Clock Display Sta ...
-
Kenwood KDC-5019 - page 3
— 3 — 2 Wa rning Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety . Location : Bottom Panel FCC W ARNING This equipment ...
-
Kenwood KDC-5019 - page 4
— 4 — English Safety precautions To prevent injury or fire, take the following precautions: • Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery , or ground wires, make sure to use automotive- grade wires or other wires with a 0.75mm 2 (A W ...
-
Kenwood KDC-5019 - page 5
— 5 — • If you experience problems during installation, consult your Kenwood dealer . • If the unit fails to operate properly , press the Reset button. The unit returns to factory settings when the Reset button is pressed. If the unit still fails to operate properly after the Reset button has been pressed, contact your local KENWOOD dealer ...
-
Kenwood KDC-5019 - page 6
— 6 — English About CDs Handling CDs • Don’t touch the recording surface of the CD. • CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. • Don’t stick tape etc. on the CD. Also, don’t use a CD with tape stuck on it. When using a new CD If the CD cente ...
-
Kenwood KDC-5019 - page 7
Press the [SRC] button. Source required Display T uner "TUNER" CD "CD" External disc "DISC"/"CD2" Auxiliary input "AUX" Standby (Illumination only mode) "ALL OFF" For Auxiliary input one of the below optional accessories is necessary . - KCA-S210A - CA-C1AX - CD changer with an Auxiliary i ...
-
Kenwood KDC-5019 - page 8
1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below . 4 Adjust the Audio item Press the [ 4 ] or [ ¢ ] button. Adj ...
-
Kenwood KDC-5019 - page 9
Switching the information displayed. Press the [DISP] button. Each time the button is pressed the display switches as shown below . In T uner source Information Display Frequency Station name "SNPS" In CD & External disc source Information Display T rack T ime Disc name "DNPS" Disc title (In External disc source) "D-TIT ...
-
Kenwood KDC-5019 - page 10
Selecting the display when this device is switched to Auxiliary input source. 1 Select Auxiliary input source Press the [SRC] button. Select the "AUX" display . 2 Enter Auxiliary input display setting mode Press the [DISP] button for at least 2 seconds. Auxiliary Input Display Setting Characters can be entered by using a remote with a num ...
-
Kenwood KDC-5019 - page 11
The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the Faceplate 1 Tu rn the ignition OFF or press the [SRC] button for at least 1 second. The power turns OFF and the faceplate slides open. 2 Holding the center part of the faceplate pull it out. • When the faceplate is kept remove open, according to the ...
-
Kenwood KDC-5019 - page 12
T uner features Prevents tampering with the unit while your car is being serviced etc. Hiding the control panel Press the [SRC] button for at least 1 second. The faceplate slides open. When the time set in <OFF Wait T ime Setting> (page 20) lapses, the faceplate is hidden and the power turns OFF . Showing the control panel Press the left part ...
-
Kenwood KDC-5019 - page 13
Putting the station in the memory . 1 Select the band Press the [FM] or [AM] button. 2 Select the frequency to put in the memory Press the [ 4 ] or [ ¢ ] button. 3 Put the frequency in the memory Press the [#1] — [#6] button for at least 2 seconds. The preset number display blinks 1 time. On each band, 1 station can be put in the memory on each ...
-
Kenwood KDC-5019 - page 14
CD/External disc control features Calling up the stations in the memory . 1 Select the band Press the [FM] or [AM] button. 2 Call up the station Press the [#1] — [#6] button. Preset T uning Putting stations with good reception in the memory automatically . 1 Select the band for Auto Memory Entry Press the [FM] or [AM] button. 2 Open Auto Memory E ...
-
Kenwood KDC-5019 - page 15
Fast Forwarding Hold down on the [ ¢ ] button. Release your finger to play the disc at that point. Reversing Hold down on the [ 4 ] button. Release your finger to play the disc at that point. Fast Forwarding and Reversing Playing discs set in the optional accessory disc player connected to this unit. Press the [SRC] button. Select the display for ...
-
Kenwood KDC-5019 - page 16
Playing the first part of each song on the disc you are listening to and searching for the song you want to listen to. 1 Start T rack Scan Press the [SCAN] button. "Scan ON" is displayed. 2 Release it when the song you want to listen to is played Press the [SCAN] button. T rack Scan Replaying the track/disc you're listening to. Press ...
-
Kenwood KDC-5019 - page 17
Selecting the CD displayed in the DNPS of the CDs set in the Disc changer . 1 Enter DNPP mode Press the [DNPP] button on the remote. When "DNPP" is displayed the DNPS display in order . Forward / Reverse display Press the [DISC–] or [DISC+] button. 2 When the disc you want is displayed Press the [OK] button on the remote. The disc being ...
-
Kenwood KDC-5019 - page 18
Because authorization by the Security Code is required when it's removed from the vehicle, personalizing this unit is by using the Security Code is a help in preventing theft. Security Code Setting during operation beep sound etc. functions. The Menu system basic operation method is explained here. The reference for the Menu items and their se ...
-
Kenwood KDC-5019 - page 19
1 Select Clock Adjustment mode Press the [FM] or [AM] button. Select the "Clock Adjust" display . 2 Enter Clock Adjust mode Press the [ 4 ] or [ ¢ ] button for at least 1 second. The clock display blinks. 3 Adjust the hours Press the [FM] or [AM] button. Adjust the minutes Press the [ 4 ] or [ ¢ ] button. 4 Exit Clock adjustment mode Pr ...
-
Kenwood KDC-5019 - page 20
T emporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station. Display Setting "CRSC ON" The CRSC is ON. "CRSC OFF" The CRSC is OFF . Strong electrical fields (such as from power lines) may cause unstable sound quality when CRSC is turned ON. In such a situation, turn it OFF ...
-
Kenwood KDC-5019 - page 21
Basic Operations of remote Setting the displayed text scroll. Display Setting "Scroll Auto" Repeats scroll. "Scroll MANU" Scrolls when the display changes. The text scrolled is shown below . • CD text • MD title T ext Scroll <In External disc control mode> — 21 — [#0] — [#9] FM/AM/DISC + /DISC – ATT 38 4 / ¢ V ...
-
Kenwood KDC-5019 - page 22
[FM]/ [AM] buttons Select the band. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. [ 4 ]/ [ ¢ ] buttons T une up or down band. [#0] — [#9] buttons Press buttons [#1] — [#6] to recall preset stations. [DIRECT] button Enters and cancels the <Direct Access T uning> (page 13) mode. In T uner source [ 4 ...
-
Kenwood KDC-5019 - page 23
— 23 — Do not use any accessories other than those provided with your unit. If you use other accessories, you may damage the unit. 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - battery . 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. ...
-
Kenwood KDC-5019 - page 24
English — 24 — ANT. CONT ILLUMI P.CONT FRONT • L FRONT • R REAR • L REAR • R – + FRONT REAR 15 FM/AM antenna input 10 Rear left output (White) 11 Rear right output (Red) Fuse (10A) 27 Wiring harness (Accessory 1 ) 22 28 White/Black 31 Gray/Black 34 Green/Black 37 Purple/Black White 30 Gray 33 Green 36 Purple 39 To front left speaker 2 ...
-
Kenwood KDC-5019 - page 25
— 25 — Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Phillips truss head sheet metal screw (commercially availab ...
-
Kenwood KDC-5019 - page 26
English — 26 — 1 Insert the removal tool into the indentations in the hard rubber frame, and pull it gently until the lock is released. Accessory 8 Removal tool 3 Refer to the section "Removing the faceplate" (page 11) and then reattaching the faceplate. Never insert the taptite screws (ø2 X 4 mm) in any other screw holes than the on ...
-
Kenwood KDC-5019 - page 27
— 27 — What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. 01 ✔ The fuse has blown. ☞ After checking for short circuits in the wires, replace the fuse with one with the ...
-
Kenwood KDC-5019 - page 28
English — 28 — T uner source ? Radio reception is poor . 39 ✔ The car antenna is not extended. ☞ Pull the antenna out all the way . ✔ The antenna control wire is not connected. 40 ☞ Connect the wire correctly , referring to the section on <Connecting Wires to T erminals>. ? The desired frequency can’ t be entered with the Direct ...
-
Kenwood KDC-5019 - page 29
— 29 — If the following situations, consult your nearest service center: • Even though the disc changer is connected, the Disc Changer source is not ON, with "AUX" showing in the display during the Changer Mode. • Even though no device (KCA-S210A, CA-C1AX, KDC-CPS87, KDC-CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connect ...
-
Kenwood KDC-5019 - page 30
English — 30 — Specifications FM tuner section Frequency range (200 kHz space) ............87.9 MHz – 107.9 MHz Usable sensitivity (S/N = 30dB) .................... 9.3dBf (0.8 µV/75 Ω ) Quieting Sensitivity (S/N = 50dB) ............... 15.2dBf (1.6 µV/75 Ω ) Frequency response ( ± 3 dB) .................................30 Hz – 15 kH ...
¿Tienes una pregunta acerca de Kenwood KDC-5019?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Kenwood KDC-5019, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Kenwood KDC-5019 probablemente compartirá una forma de solucionarlo.