-
Wayne-Dalton 9800 - page 1
GARAGE DOORS & OPENERS Part No. IMPORT ANT NO TICES! Wayne-Dalton highly recommends that you read and fully under - stand the Installation Instructions and Owner’ s Manual before you attempt this installation. T o avoid possible injur y , read the enclosed instructions carefully before installing and operating the garage door . Pay close atte ...
-
Wayne-Dalton 9800 - page 2
2 Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com A. FLAGANGLES: A1. Fully Adjustable (F .A.) Flagangles A2. Quick Install (Q.I.) Flagangles B. JAM ...
-
Wayne-Dalton 9800 - page 3
I m p o r t a n t S a f e t y I n s t r u c t i o n s DEFINITION OF KEY WORDS USED IN THIS MANUAL: W ARNING W ARNING INDICA TES A POTENTIALL Y HAZARDOUS SITUA TION WHICH; IF NOT AVOIDED , COULD RESUL T IN SEVERE OR FA T AL INJURY . CAUTION: PROPER TY DAMAGE OR INJURY CAN RESUL T FROM FAILURE TO FOLLOW INSTRUCTIONS. IMPORT ANT : REQUIRED STEP FOR SA ...
-
Wayne-Dalton 9800 - page 4
1/4”-20 x 11/16” Self drilling screws (as required) 5/16” x 1 5/8” Hex head lag screws (as required) (2) 3/8”- 16 Hex nuts 1/4”-14 x 5/8” Self tapping screws (as required) 1/4”-20 x 9/16” Track bolts (as required) 1/4”-20 x 5/8” Tamper resistant Self drilling screws (as required) Clevis pins 5/16” Washers Cotter pins 1/4”- ...
-
Wayne-Dalton 9800 - page 5
opening during installation. Equally space nails approximately 12” to 18” apart. For Fully Adjustable track: For the header , align the weatherstrip 1/8” to 1/4” inside the header edge, and temporarily secure it to the header with equally spaced nails. Starting at either side of the jamb, fit the weatherstrip up tight against the temporari ...
-
Wayne-Dalton 9800 - page 6
INST ALLA TION Before installing your door , be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. Failure to do so may result in an improperly installed door . NOTE: Reference TDS 160 for general garage door terminology at www.dasma.com . Quick Install Flag Angles T ools: None ...
-
Wayne-Dalton 9800 - page 7
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com pattern. Secure jamb bracket using (1) 1/4”-20 x 9/16” track bolt and (1) 1/4”-20 flange hex ...
-
Wayne-Dalton 9800 - page 8
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com Vertical track assembly Jamb bracket Flag angle Flag angle lag screw locations 5/16” x 1-5/8” L ...
-
Wayne-Dalton 9800 - page 9
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com of the door; tighten the bottom lag screw . Flag angles must be parallel to the door sections. Repe ...
-
Wayne-Dalton 9800 - page 10
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com Center bracket Vertical line Mounting surface Horizontal line Center of end bearing bracket Equal d ...
-
Wayne-Dalton 9800 - page 11
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com Center bracket bushing assembly Stationary spring cone (2) 3/8”-16 x 1-1/2” Hex head bolts (2) ...
-
Wayne-Dalton 9800 - page 12
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com T orsion shaft Winding cone Spring Approved winding rods Set screws Rear Back Hangs T ools: Ra tche ...
-
Wayne-Dalton 9800 - page 13
Please Do Not Return This Product T o The Store. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pages business listings or go to the Find a Dealer section online at www.W ayne-Dalton.com Sound framing members Perforated angle Horizontal track (3) 5/16” Bolts and nuts Perforated angle ...
-
Wayne-Dalton 9800 - page 14
Door Arm Hookup T ools: Needle nose pliers Align hole in the door arm with holes in drawbar operator bracket tabs, as shown. Insert 5/16” x 1-1/4” clevis pin, making sure hole in clevis pin is outside of second tab of drawbar operator bracket. Insert hairpin cotter into clevis pin hole and spread hairpin cotter to secure assembly , as shown. Sp ...
-
Wayne-Dalton 9800 - page 15
Cleaning Y our Garage Door IMPORT ANT : DO NOT USE A PRESSURE W ASHER ON YOUR GARAGE DOOR! While factory-applied finishes on garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a period of time. Slight chalking may also occ ...
-
Wayne-Dalton 9800 - page 16
W ARNING W ARNING NEVER REMOVE, ADJUST , OR LOOSEN THE BOL TS, SCREWS AND/OR LAG SCREWS ON THE COUNTERBALANCE (END OR CENTER BEARING BRACKETS) SYSTEM OR BO TTOM CORNER BRACKETS OF THE DOOR. THESE BRACKETS ARE CONNECTED TO THE SPRING(S) AND ARE UNDER EXTREME TENSION. TO AVOID POSSIBLE SEVERE OR F A T AL INJURY , HAVE ANY SUCH WORK PER- FORMED BY A T ...
-
Wayne-Dalton 9800 - page 17
Lifetime limited warranty Model 9800 Subject to the terms and conditions contained in this Lifetime Limited Warranty , Wayne-Dalton (“Manufacturer”) warrants the sections of the garage door for as long as you own the door against: i) The door becoming inoperable due to rust-through of the steel skin backer from the core of the door section, cau ...
-
Wayne-Dalton 9800 - page 18
AFTER INST ALLA TION IS COMPLETE, F ASTEN THIS MANUAL NEAR THE GARAGE DOOR. Please Do Not Return This Product T o The Store Thank you for your pur chase. Contact your local Wayne-Dalton dealer . T o find your local Wayne-Dalton dealer , refer to your local yellow pa ges business listings or go to the Find a Dealer section online at www .Wayne-Dalt ...
¿Tienes una pregunta acerca de Wayne-Dalton 9800?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Wayne-Dalton 9800, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Wayne-Dalton 9800 probablemente compartirá una forma de solucionarlo.