-
Hans Grohe 14801XX1 - page 1
Bar Faucets Installation Instructions / W arranty Allegro E 14801XX1 HighArc ...
-
Hans Grohe 14801XX1 - page 2
2 English T echnical Specification Recommended water pressure 14.7 - 72.5 PSI Recommended hot water temp. 120° - 140° F* Hole size in mounting surface 1-1/2” Max. mounting surface thickness 2 3/8” Max. flow rate 2.2 GPM *Please know and follow all applicable local codes when setting the temperature on the water heater . Installation Considera ...
-
Hans Grohe 14801XX1 - page 3
3 Installation Push the spout into place on the faucet. T ighten the spout set screw . Install the hot and cold supply lines to the stops with 3/8” compression fittings (included). Use two wrenches, as shown, to prevent the supply hoses from twisting. Place the faucet and sealing washer on the mount- ing surface. If the mounting surface is less t ...
-
Hans Grohe 14801XX1 - page 4
4 Install the handle Install the handle screw on the cartridge stem. T ighten only 4 turns. Place the handle over the stem and handle screw . Press it firmly into place. Use a 4 mm Allen wrench to finish tightening the screw . Install the screw cover . User Instructions Push the handle to the right to turn the water on. Push it back to the left to ...
-
Hans Grohe 14801XX1 - page 5
5 Allegro E Bar Faucet 14801XX1 T echnical Specification Recommended water pressure 14.7 - 72.5 PSI Recommended hot water temp. 120° - 140° F* Hole size in mounting surface 1-1/2” Max. mounting surface thickness 2 3/8” Max. flow rate 2.2 GPM *Please know and follow all applicable local codes when setting the temperature on the water heater . ...
-
Hans Grohe 14801XX1 - page 6
6 Install the hot and cold supply hoses on the stops with 3/8” compression fittings (included). Use two wrenches, as shown, to prevent the hoses from twist- ing and becoming loosened from the faucet. Do no t a l lo w e i th e r h os e t o t w is t . T w i st i ng th e s up p ly h o se m a y ca u se it to lo o se n fr om th e fa uc e t, wh i ch ma ...
-
Hans Grohe 14801XX1 - page 7
7 Données techniques Pression d’eau recommandée 14,7 - 72,5 psi T empérature recommandée pour l’eau chaude 120° – 140°F* Dimension du trou dans la surface de montage 1-1/2 po Profondeur maximale de la surface de montage 2 3/8 po Débit 2,2 gpm max. tuyaux d’arrivée de 3/8 po - requièrent des raccords à compression de 3/8 po (non co ...
-
Hans Grohe 14801XX1 - page 8
8 Installation du robinet Enclenchez le bec en col de cygne sur le corps du robinet. Serrez la vis. Placez l’anneau d’étanchéité et le robinet sur la surface de montage. Installez la rondelle de plastique, la rondelle en fibre, la rondelle de friction et l’écrou de montage. Si l’épaisseur du comptoir dépasse 1 3/8 po (3,5 cm) ou si l? ...
-
Hans Grohe 14801XX1 - page 9
9 Installation de la poignée Installez la vis de la poignée sur la tige. Serrez 4 tours complets. Placez la poignée sur la tige et vissez la poignée. Appuyez bien fermement sur la poignée pour la fixer en place. Utilisez une clé hexagonale de 4 mm pour finir de serrer la vis. Installez le cache-vis. Instructions à l’intention de l’utilis ...
-
Hans Grohe 14801XX1 - page 10
10 Données techniques Pression d’eau recommandée 14,7 - 72,5 psi T empérature recommandée pour l’eau chaude 120° – 140°F* Dimension du trou dans la surface de montage 1-1/2 po Profondeur maximale de la surface de montage 2 3/8 po Débit 2,2 gpm max. * V ous devez connaître et respecter tous les codes de plomberie locaux applicables pou ...
-
Hans Grohe 14801XX1 - page 11
11 Installation du robinet 14801XX1 Placez l’anneau d’étanchéité et le robinet sur la surface de montage. Installez la rondelle en fibre, la rondelle de friction et l’écrou de montage. Serrez l’écrou de montage et les vis de serrage. Connectez les tuyaux d’arrivée d’eau chaude et d’eau froide aux tuyaux d’alimentation à l’a ...
-
Hans Grohe 14801XX1 - page 12
12 Replacement Parts 1 flange 96468XX0 2 nut 96461000 3 cartridge 92730000 4 aerator 13085XX0 5 connection hose 96316001 6 fixing set 95049000 7 sealing set 92646000 8 plastic washer 97523000 9 axial ring 97558000 10 screw 97662000 11 handle screw 96059000 12 seal 95008000 13 handle, Solaris 06981XX0 14 handle, Stratos 06983XX0 15 handle, Metro 069 ...
-
Hans Grohe 14801XX1 - page 13
13 Cleaning Recommendation for Hansgrohe Pr oducts Modern lavator y faucets, kitchen faucets, and showers consist of ver y different materials to comply with the needs of the market with regard to design and functionality . T o avoid damage and returns, it is necessar y to consider certain criteria when cleaning. Cleaning Materials for Faucets and ...
-
Hans Grohe 14801XX1 - page 14
14 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY ...
-
Hans Grohe 14801XX1 - page 15
15 C. Labor or other expenses for the disconnection, deinstallation, or return of the product for warranty service, or for installation or reinstallation of the product (including but not limited to proper packaging and shipping costs), or for installation or reinstallation of the product. D. Accessories, connected materials and products, or relate ...
-
Hans Grohe 14801XX1 - page 16
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770-360-9880 • Fax 770-360-9887 www .hansgrohe-usa.com US - Installation Instructions • Part No. 90551001-03 • Revised 09/2008 ...
¿Tienes una pregunta acerca de Hans Grohe 14801XX1?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hans Grohe 14801XX1, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hans Grohe 14801XX1 probablemente compartirá una forma de solucionarlo.