-
Makita 6OLODW - page 1
Cordless Drills - Capacities No load speed Net weight Steel I Wood Wood screw 10 mm 1318") 600 Rimin. 1.1 kg (2.4 Ibs) 4.5 mm x 20 mm (311 6" x 314") 10 mm (318") MODEL 6010D 10 mm (318") MODEL 6OlODW 10 mm (318") MODEL 6OlODWK With Fast Charger With Fast Charger and Carrying Case Overall length 227 mm 19") INSTRU ...
-
Makita 6OLODW - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invit ...
-
Makita 6OLODW - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext ...
-
Makita 6OLODW - page 4
IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord I. SAVE THESE INSTRUCTIONS - This manual 25 50 100 150 18 18 18 16 contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using ba ...
-
Makita 6OLODW - page 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the batte ...
-
Makita 6OLODW - page 6
Installing or removing battery cartridge *Always switch off the tool before inser- tion or removal of the battery cartridge. *To remove the battery cartridge, pull out the set plate on the bottom of the tool and grasp both sides of the cartridge while withdrawing it from the barrel. To insert the battery cartridge, align the tongue on the battery c ...
-
Makita 6OLODW - page 7
Bit installation & removal CAUTION : Always set the Forward-Reverse switch lever to NEUTRAL when installing, removing or adjusting bits or accessories. Chuck When installing a drill bit, notice that there are three holes in the chuck at which you must use the key for tighten- ing. Insert the chuck key in any of the 3 holes and turn to the left ...
-
Makita 6OLODW - page 8
Switch action Move the reversing switch lever to the position for clockwise rotation or the )J& position for counterclockwise. To start the tool, simply pull the trigger. Release the trigger to stop. When the re- versing switch lever is in the neutral posi- tion, the tool will not start even if you pull the trigger & Reversing -switch lever ...
-
Makita 6OLODW - page 9
*Pressing down too hard on the tool will not speed up the drilling. In fact, this undue pressure will only serve to damage the tip of your drill bit, decrease your drilling per- formance and shorten the service of the tool. *There is a tremendous force exerted on the tool/bit at the time of hole break through. Grip the drill firmly and exert care w ...
-
Makita 6OLODW - page 10
Grip .The grip shown on the right is recom- mended. However, grip the tool firmly with both hands when drilling a large- diameter hole. *The hole on the heel of the tool is a con- venient way to carry it by a cord, hook or other means. 10 ...
-
Makita 6OLODW - page 11
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bits 0 Fast charger 0 Charger 12V for car Phil ...
-
Makita 6OLODW - page 12
Mar~-l1-'87 US 10 mm (318") CORDLESS DRILL Model 6010D Note: The switch and other part configurations may differ from country to country. 12 ...
-
Makita 6OLODW - page 13
MODEL 6010D Mar 11 87 EN 10 12 13 14 16 17 25 27 'Ff $:D DESCRIPTION ,",",, DESCRIPTION 1 1 1 1 7 1 1 1 11 21 31 41 51 61 71 81 91 Pan Head Screw M5x18 Drill Chuck S10 Gear Plane Bearing 5 DC Motor 7 2 V Plane Bearing 3 Gear 13-58 Switch Plane Bearing 3 Housing Ser lWilh Item 271 Baffery 7000 Holder 6 Name Plate Pan Head Screw M4x22 ...
-
Makita 6OLODW - page 14
The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. 1 Ni-Cd To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been ...
¿Tienes una pregunta acerca de Makita 6OLODW?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 6OLODW, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 6OLODW probablemente compartirá una forma de solucionarlo.