-
Whirlpool AWM 1007 - page 1
DEFINITION OF USE This appliance is exclusivel y destined to wash and spin machine washable laundry in quantities which are usual for private households. • Observe the instructions given in these Instructions for Use and in the separa te Programme Chart when using the washing machine. • Keep these Instructions for Use and the Programme Chart; i ...
-
Whirlpool AWM 1007 - page 2
FIRST WASH CYCLE PRECAUTIONS AND GENERAL RECOMMENDATIONS 1.Safety Instructions • This washing machine is not intended for use by persons (including children ) with reduced physical, sensory or mental capabiliti es, or lack of experience and knowledge, unless they have been given supervision or instructio n concerning use of the appliance by a per ...
-
Whirlpool AWM 1007 - page 3
DESCRIPTION OF THE WASHING MACHINE CHILD SAFETY 1. Worktop 2. Control panel 3. Detergent dispenser 4. After-Sales Service sticker (on the front panel behind the door frame) 5. Door 6. Door handle • To open the door pull the handle • Close the door by pushing it firmly (the lock will click into place) 7. Adjustable feet 8. Filter behind the cove ...
-
Whirlpool AWM 1007 - page 4
DETERGENTS AND ADDITIVES P ouring in deter gents and additives Pull out the d eter gen t disp enser to its full e xten t. P our in deter g ent: Chamber • Detergent for the pre-wash Chamber • Detergent for the main wash • Stain remover • Water softener For use of powd er deter g ent : Push the gr ey slid er o f the divid er insert to th e le ...
-
Whirlpool AWM 1007 - page 5
Notes: • Keep detergents and additives in a dr y place and out of reach of children. • If you use descaling agents , dyes or bleaches, make sure they are suitable for washing ma chine use. Descaler could contain com ponents that can damage pa rts of your washing machine. • Do not use solvents (turpentine, benzine, etc.) Do not machine wash fa ...
-
Whirlpool AWM 1007 - page 6
DRAINING RESIDUAL WATER Residual water should be removed: • before moving a washing machine (relocation), • when installing in areas prone to frost and • before removing the filter. 1. Before emptying the residua l water, switch the appliance off and un plug it from the mains socket. Make sure that the water ha s cooled before draining. 2. Tu ...
-
Whirlpool AWM 1007 - page 7
CLEANING THE FILTER The filter must be taken out if: • the washing machine does not drain properly, • small items, e. g. buttons and coins rattle in the pump and • 2 to 3 times a year for inspection. You must remove the residual water before t aking out the filter. Carry out the steps in the “Draining Residual Water” section, but only up ...
-
Whirlpool AWM 1007 - page 8
CARE AND MAINTENANCE Appliance exterior and control panel • Clean using a neutral hou sehold detergent and a damp cloth (do not use abrasive products or solvents). • Dry with a soft cloth. Appliance interior • If you never or seldom wash your laundry at 95°C, we recommend to occasionally run a 95°C programme without lau ndry, adding a small ...
-
Whirlpool AWM 1007 - page 9
TROUBLESHOOTING GUIDE This washing machine is equipped with automatic safety functions which de tect and diagnose faults at an early stage and react appropriately. Often, however, the faul ts detected are small enough to be solved in a matter of minutes. For example: The appliance will not start; no lamp lights up. Check whether: • The appliance ...
-
Whirlpool AWM 1007 - page 10
What should I do when the automatic safety system detects a malfunction? The programme is interrupted and various indicators (if available) poi nt to the source of the fault. Fault description table a. No or not enough water inlet • Open the water tap and check wether the water supply pressure is sufficient. • Remove kinks in the water supply h ...
-
Whirlpool AWM 1007 - page 11
AFTER-SALES SERVICE Before contacting After-Sales Service: 1. Try to remedy the problem yourself (see “Troubleshooting Guide”). 2. Restart the programme to check whether the problem has so lved itself. 3. If the machine continues to function incorrectly, call After-Sales Service. Specify: • The nature of the problem. • Appliance and model N ...
-
Whirlpool AWM 1007 - page 12
INSTALLATION Remove the transit bolts 1. Slacken the four bolts with the spanner supplied. 2. Unscrew the bolt by hand. 3. Grip the bolt and remove it through the la rge aperture. 4. Seal the resulting holes usin g the plastic caps supplied. To do this, insert the caps in the wide part of the hole in the direction of the arro w and push them into t ...
-
Whirlpool AWM 1007 - page 13
Adjust the feet Small unevennesses in the floor can be compensated for by screwing the four appliance feet up or down (never use pieces of wood, cardboa rd or similar material): 1. The washing machine must be installed horizontally in width and depth. Use a spirit level. 2. Loosen the locknut cloc kwise using the wrench provided. 3. Adjust the heig ...
-
Whirlpool AWM 1007 - page 14
Connect the water supply hose(s) (A or B, depending on the model) • If your washing machine has one inlet hose and one inlet valve on the back: connect to cold water supply only. • If your washing machine ha s two inlet hoses and two inlet valves on the back: co nnect to cold and hot water supply, or to cold water supp ly only by us ing the Y-p ...
-
Whirlpool AWM 1007 - page 15
5019 301 15247 GB Printed in Germany Ecological P aper 1/0410 ELECTRICAL CONNECTION For Great Britain only Warning - this appliance must be earthed Fuse replacement If the mains lead of this a ppliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S. T.A. approved fuse to BS 1362 type and proceed as foll ...
¿Tienes una pregunta acerca de Whirlpool AWM 1007?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Whirlpool AWM 1007, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Whirlpool AWM 1007 probablemente compartirá una forma de solucionarlo.