-
Hoover 53391 - page 1
Review this manual before operating cleaner ...
-
Hoover 53391 - page 2
This cleaner was inspected and packaged carefully before being shipped from the factory. If you should happen to need assistance during assembly or operation, call l-800-944-9200 for automated referral of authorized service outlet locations ( U.S. only ) or l-330-499-9499 to speak with a representative in our Consumer Response Center. 1 DO NOT RETU ...
-
Hoover 53391 - page 3
lmwwtant Safeauards! - -m- - - - _----- _- -rl-- -- When using an electrical appliance, always follow basic precautions, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Warning. injury: n To reduce the risk of fire, electric shock, or Do not use outdoors or on wet surfaces. Close supervision is necessary when any applianc ...
-
Hoover 53391 - page 4
Unpacking Unpack cleaner from carton and identify the parts shown. Re- move and dispose of the card- board packing. A. Canister cleaner B. Power nozzle C. Paper bag D. Extension wands and hose The assembled cleaner will look like the drawing below. T 16 15-l 3 ...
-
Hoover 53391 - page 5
Cleaner description 1. 2. 3. 4. 5. 6. 7. a. 9. Cover: remove by lifting up top section of carrying handle and pulling forward. Carrying handle Check bag indicator: shows red when paper bag should be checked for fullness. Extension wands: use with power nozzle. If added length is desired when using cleaning tools, add one or both wands to hose. Spri ...
-
Hoover 53391 - page 6
Questions or Concerns? The Hoover Company wants to quickly resolve any concerns about your cleaner or questions regarding its use. Look on the list provided with the product for your local Hoover Factory Service Center or in the Yellow Pages under “Vacuum Cleaners - Household” for the nearest Authorized Hoover Warranty Service Dealer (Depot) or ...
-
Hoover 53391 - page 7
Attach second wand to the first. Position cord into cord clips on wands, placing excess cord between nozzle and bottom cord clip. To attach hose to wands, rotate plastic latch ring on hand grip until slots in opening align. Push hand grip onto wand so that button projection fits into slot. Turn plastic latch ring to lock wand in place. Push plug on ...
-
Hoover 53391 - page 8
How to use To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plu ...
-
Hoover 53391 - page 9
Suction regulator The suction regulator is located on the hand grip and is used to increase or decrease suction for various cleaning tasks. If the power nozzle is difficult to push on some carpet, open the suction regulator. This will prevent damage to the belt. Cleaning tools The cleaning tools have many uses. Select the tool best suited for the c ...
-
Hoover 53391 - page 10
To connect and remove tools To connect tools, insert end of tool into extension wand and snap into -. position. To disconnect, press down on the center of the spring latch and remove tool. Tools attach to hand grip by rotating plastic ring until slots in the opening align. Insert tool and turn latch ring, as shown, to lock tool in place. To remove ...
-
Hoover 53391 - page 11
How to store Your cleaner can be stored on end as shown in the illustration. Store power nozzle with handle in upright position. The hose and extension wands can be stored disassembled from the cleaner if desired. Maintenance The following sections are concerned with proper maintenance of the cleaner. Familiarize yourself with these home maintenanc ...
-
Hoover 53391 - page 12
How to replace Disconnect cleaner from electrical outlet. 1. Remove cover by lifting top section of carrying handle and pulling forward. 3. Place lower notched edge of new bag collar into grooves located inside front of cleaner. 2. Depress latch and lift out used bag. 4. Pull collar forward until latch snaps into collar. Open folds of bag. Push top ...
-
Hoover 53391 - page 13
Obstructions Remove larger items from carpet and floor surfaces before vacuuming to help prevent obstructions in hose, wands or nozzle connector, and to maintain cleaning effectiveness of your cleaner. There are two conditions that will indicate that an obstruction has occurred: 1. Cleaner stops running (See Thermal Protector section.) 2. Cleaner c ...
-
Hoover 53391 - page 14
How to clean Disconnect cleaner from eiectri- cai outlet. The secondary filter is located inside the cleaner behind the paper bag. To remove filter, first remove cover of cleaner, then lift out filter. Clean filter by rinsing it in water. When dry, slide filter back into position. Do not operate cleaner without the secondary fiiter in place. The be ...
-
Hoover 53391 - page 15
2. Return nozzle to original position; and lift off nozzle cover. 1 MOTOR PULLEY 3. If the belt is not broken, pull it off the motor pulley. 4. Lift up end of agitator. Remove old belt from agitator pulley and replace with new belt. 5. Stretch belt back and attach to motor pulley. Hold opposite end of agitator in place. Push belt end forward, rotat ...
-
Hoover 53391 - page 16
6. Position nozzle cover on front lip of nozzle base. Press cover into place. Turn nozzle over and replace screws. The agitator When to replace Disconnect cleaner fern eiectri- cai outlet. When agitator brushes are worn, the agitator should be replaced. To check condition of brushes, move the edge of a card across agitator opening while turning agi ...
-
Hoover 53391 - page 17
Lubrication The motor is equipped with bearings, which have been lubricated for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to either motor bearing. The agitator is equipped with two ball bearings that should be lubricated periodically by a Hoover Factory Service Center or an Authorized Warra ...
-
Hoover 53391 - page 18
Service To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: 0 checking the Yellow Pages under “Vacuum Cleaners - Household” OR - 0 checking the list of Factory Service Centers provided with this cleaner OR - 0 calling I-800-944-9200 ...
-
Hoover 53391 - page 19
0 1/, HOOVER and V# are registered trademarks THE HOOVER COMPANY, NOFiiH CANTON, OHIO 44720 R4 4-96 S3395040/9 I Litho USA 56513-331 ...
¿Tienes una pregunta acerca de Hoover 53391?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hoover 53391, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hoover 53391 probablemente compartirá una forma de solucionarlo.