-
Graco RTX 650 - page 1
311767C Operation Interior T exture Spra yer RT X 6 5 0 For W ater- Based Materials Only Model 254973: 50 psi (3.5 bar) Maxim um Fluid W or king Pressure 100 psi (7 bar) Maxim um Air Input Pressure Related Manuals Important Safety Instructions Read all warnings and instr uctions in this manual. Sav e these instr uctions . 311777 311771 Model 254973 ...
-
Graco RTX 650 - page 2
Warnings 2 Wa r n i n g s The f ollowing are gener al warnings related to the set up , use , groun ding, maintenance and re pair of this equipmen t. Additional, mo re specific warnings ma y be f ound through out the body of this manu al where applicab le. Symbols appearing in the body of the man ual refer to these gener al warnings. Whe n these sym ...
-
Graco RTX 650 - page 3
Warnings 3 Electric Shoc k Hazard T o reduce the risk of electric shock: • Be sure spr a ye r is adequately g rounded through electrical outlet . • Use only 3-wire, e xtension c ords . • Mak e sure grou nd prongs are intact on spr ay er and e xtension cords. Improp er installation of grounding plug will result in a risk of electr ical shoc k, ...
-
Graco RTX 650 - page 4
Warnings 4 CA UTION W ate r or mater ial remaining in unit when te mperatures are b elow freezing can dam age motor and/or dela y pump star tup . T o insure water and material are complet ely drained out of unit: 1. Remov e material line from spra yer . 2. Tip spray er up as sh own. Bef ore adding material or star ting unit in cold wea ther , run w ...
-
Graco RTX 650 - page 5
Component Identification 5 Component Identification 3.5 cfm@40 min. Q M A K E B P J D C H G ti8369a F L N R Item Component Item Compone nt A Pump Hose Outle t J Bur p Guard B RotoFlex™ II Pump (inside) K ON/OFF Switch C T e xture Spray Gun (Manual 311777) L P ower Cord (120V , 15 ft) D Nozzle (2 included, see N ozzle Selection , page 10) M Materi ...
-
Graco RTX 650 - page 6
Preparation 6 Preparation Pressure Relief Procedure T o reduce risk of injur y , follo w this procedur e whene ver y ou see this symbol throughout this manual, Also , perf orm this procedure whene v er you : • Stop spra ying • Check or repair any par t of this syst em • Install or clean spra y nozzle 1. T ur n power s witch (K) OFF . 2. T rig ...
-
Graco RTX 650 - page 7
Setup 7 Setup T exture Spra ying 1. Connect air hose to user-su pplied air compressor & mater ial hose (G) t o mater ial hose outlet s . 2. Connect use r supplied air ho se to gun. 3. Open air valv e. 4. Connect material hose to gun. 5. Install spra y nozzle. See Recommended Nozzle Selection Char t , page 10. 6. Fill material hopper with 1 gall ...
-
Graco RTX 650 - page 8
Setup 8 8. P oint gun into waste b u c ket and pull trigge r to pump water t hrough the system. Cont inue to trigger gun until material hopper is empty . 9. Install bur p guard (J). Caution , page 3. 10. Add pre-mixed texture mix to mater ial hoppe r . See Mixing Mate rial, pag e 9. 11. Con tinue to trigger gun and spr ay into w aste buc ket until ...
-
Graco RTX 650 - page 9
Mixing Material 9 Mixing Material Dry Mix - 40 lb (18 kg) ba g. 1. Slo wly add one 40 l b . (18 kg) bag of te xture material to 5-6 gallons (18.9- 22.7 liters) of cle an water as instructed on the bag instructions . 2. Agitate to mix, using a ha lf-inch, variable speed drill with mixing paddle , to a smooth, lump-free consistency . 3. Allow ceiling ...
-
Graco RTX 650 - page 10
Spray Techniques 10 Spra y T echniques Recommended Nozzle Selection Char t 1 Control air v olume with gun air v alve . 2 F or more material v olume tr y a larger nozzle. Adjusting the System Sufficient fluid ou tput (v olume and pressure) and good atomization is a balance of atomizin g air , material thickne ss/material flow an d nozzle selection. ...
-
Graco RTX 650 - page 11
Shutdown and Cleanup 11 Shutdo wn and Cleanup T exture Spra ying (5 gallon Material Hopper) When you hav e finished spra ying: 1. T ur n spray er power switch (K) ON (air comp ressor can remain OFF) . 2. Close gun air v alve . 3. T rigger gun into buc ket until most of te xture mix is pumped out. 4. Fill material hopper with 2-4 gallons of clean wa ...
-
Graco RTX 650 - page 12
Troubleshooti ng 12 T r oubleshooting Prob lem C ause Solution Spra yer won’t r un P ower s witch not o n T ur n switch on. No pow er at wall outle t Chec k outlet by plugging in another appliance . If appliance does not work, try another outlet. Wrong size ge nerator Use a 3500 wa tt or larger gener ator . Ref er to Generator Require ments , pag ...
-
Graco RTX 650 - page 13
Troubleshooting 13 Speed of a pplication slow or slower New pump hose not broken in properly Run pump d r y f or no more than 2 minutes. Material too thic k Thin material. Nozzle too small Change nozzles to a larger siz e. See Recommended Nozzle Selection Char t, page 10. T oo much air being used P ar tially close gun air v alve to redu ce air flow ...
-
Graco RTX 650 - page 14
Technical Data 14 Te c h n i c a l D a t a Main Unit Po wer Re quirements . . . . . . . . . . . . . . . . . . . . 120 V a c, 60 Hz, 15A, 1 phase Maximum Fluid Working Pre ssure . . . . . . . . . . . . . . . . . . 50 psi, (3.5 bar) Maximum Air Working P ressure . . . . . . . . . . . . . . . . . . . . 100 psi (7.0 b ar) Compresso r Specifications . . ...
-
Graco RTX 650 - page 15
Notes 15 Notes ...
-
Graco RTX 650 - page 16
Graco Warrant y 16 Graco W arranty Graco warrants all equipment ref erenced in this document which is manufactured by Gr aco and bearing its nam e to be free from de fec t s i n material and workmanship on the date of sale to the original purch aser f or use. With the e xception of any special, e xtend ed, or limited warr anty published b y Graco , ...
¿Tienes una pregunta acerca de Graco RTX 650?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Graco RTX 650, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Graco RTX 650 probablemente compartirá una forma de solucionarlo.