-
Pelco C2403M-C - page 1
ADDENDUM P elco W or ldwide Headquar t ers 3500 Pelco Way • Clovis , California 93612 USA USA & Canada • T el: 800/289-9100 • Fax: 800/28 9-9150 International • T el: 1-559/292-1 981 • Fax : 1-559/348-112 0 www .pelco.com Addendum No. C3409M Date December 22, 2005 Manuals Affected C2462M-B, C2403M-C, C2 410M-H, C2491M-B, C2496M Manual ...
-
Pelco C2403M-C - page 2
090 Series Camclosure ® Indoor Integrated Camera System ® INST ALLA TION C2462M-B (10/05) ...
-
Pelco C2403M-C - page 3
2 C2462M-B (10/05) CONTENTS Section Page IMPORT ANT SAFEGUARDS AND WARNINGS .................................................................................... 3 WELCOME ......................................................................................................................................... 4 REMOVE THE BUBBLE ..................... ...
-
Pelco C2403M-C - page 4
C2462M-B (10/05) 3 IMPORT ANT SAFEGUARDS AND W ARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and must not be installed where exposed to rain and ...
-
Pelco C2403M-C - page 5
4 C2462M-B (10/05) WELCOME Thank you for purchasing Pelco’ s Camclosure ® Integrated Camera System for indoor applications. The ICS090 Series system integrates a camera and lens package in a small, discreet dome. The system is easy to install and can be mounted to the surface of a ceiling/wall or recessed in a ceiling/wall. Prior to installation ...
-
Pelco C2403M-C - page 6
C2462M-B (10/05) 5 REMOVE THE BUBBLE T urn the bubble counterclockwise and lift (refer to Figure 1). Place the bubble on a non-abrasive surface. If the unit is supplied with a liner , remove the liner before installing the unit. T o remove the liner , gently lift it from the unit. Place the liner to the side; it will be reinstalled along with the b ...
-
Pelco C2403M-C - page 7
6 C2462M-B (10/05) INST ALL THE BACK BOX The installation methods for the ICS090 Series include the following: • Mount to the surface of a ceiling/wall • Install in a suspended ceiling • Install in a fixed ceiling/wall • Mount to the surface of a 4S standard electrical box • Install in a 4S deep electrical box Select the best method for y ...
-
Pelco C2403M-C - page 8
C2462M-B (10/05) 7 Figure 2. Ceiling/Wall Installation Installation to Surface of a Ceiling/Wall Refer to Figure 2 for the following steps. Refer to Figure 3 if installing the unit to a concrete ceiling/wall. 1. Pull video and power wires through the ceiling/wall. 2. Connect the video cable/wires. BNC – Connect the BNC connector from the Camclosu ...
-
Pelco C2403M-C - page 9
8 C2462M-B (10/05) SURF ACE MOUNT RING BACK BO X ST ANDOFF Figure 5. How to Remove Surface Mount Ring from Back Box In-Ceiling Installation – Suspended Ceiling Refer to Figure 4 for the following steps. 1. Remove the ceiling tile from the ceiling. 2. Cut a four -inch diameter hole in the ceiling tile. 3. Remove the surface mount ring from the bac ...
-
Pelco C2403M-C - page 10
C2462M-B (10/05) 9 In-Ceiling Installation – Fixed Ceiling/Wall Refer to Figure 6 for the following steps. 1. Cut a four -inch diameter hole in the ceiling/wall. 2. Remove the surface mount ring from the back box. Refer to Figure 5 and do the following: a. Place fingers on the circular marks located on the sides of the surface mount ring. b. Pinc ...
-
Pelco C2403M-C - page 11
10 C2462M-B (10/05) Installation to Surface of a 4S Standard Electrical Box Refer to Figure 7 for the following steps. 1. Attach the adapter ring to the 4S box with the two 8-32 x 1.00-inch screws (supplied). 2. Connect the video cable/wires. BNC – Connect the BNC connector from the Camclosure to a mating BNC connector . T wisted Pair – Blue wi ...
-
Pelco C2403M-C - page 12
C2462M-B (10/05) 11 8-32 x 1.00 (SUPPLIED) ADAPTER RING BACK BOX 8-32 X .750 (SUPPLIED) CEILING/ WALL 4S DEEP ELECTRICAL BOX Installation in a 4S Deep Electrical Box Refer to Figure 8 for the following steps. 1. Remove the surface mount ring from the back box. Refer to Figure 5 and do the following: a. Place fingers on the circular marks located on ...
-
Pelco C2403M-C - page 13
12 C2462M-B (10/05) CAMERA POSITIONING Manually rotate and tilt the camera module to position the camera. Do not over -rotate the module. Excessively turning the module in one direction could result in damage to the wiring. T ilt 140 ° Pan 360 ° Rotation 360 ° Figure 9. How to Position Camera ...
-
Pelco C2403M-C - page 14
C2462M-B (10/05) 13 Figure 11. Varifocal Lens Adjustments CAMERA ADJUSTMENTS VARIFOCAL LENS ZOOM AND FOCUS ADJUSTMENTS 1. Select a field of view by turning the zoom adjustment ring clockwise/counterclockwise. Refer to Figure 10. 2. T ighten the zoom locking screw . 3. Adjust the focus by moving the focus locking screw clockwise/counterclockwise. 4. ...
-
Pelco C2403M-C - page 15
14 C2462M-B (10/05) SWITCH SETTINGS Switch Settings for Fixed Focal Length Lens Without Auto Iris Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensa- tion (factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions where there are no bright spots that dar ...
-
Pelco C2403M-C - page 16
C2462M-B (10/05) 15 VERTICAL PHASE ADJUSTMENT (24 V AC OPERA TION ONL Y) When using more than one camera power supply , a brief vertical roll may occur on the monitor when a camera view is switched. T o eliminate vertical roll reverse the 24 V AC connections on one camera. If both cameras are connected to the same transformer , this should solve th ...
-
Pelco C2403M-C - page 17
16 C2462M-B (10/05) REINST ALL THE DOME DOME LINER INST ALLA TION If the unit is supplied with a dome liner , reinstall the liner before installing the bubble. T o install the liner refer to Figure 13 and do the following: 1. Align the studs located on the camera module with the clips on the liner . 2. Lightly pinch the sides of the liner , opposit ...
-
Pelco C2403M-C - page 18
C2462M-B (10/05) 17 SERVICE CONNECTOR An optional 4-foot service/monitor cable, part number ICS090-SC, is available for on-site setup and adjustments. T o use the cable simply plug one end of the cable directly into the service connector of the ICS090 and connect the other end to any standard BNC (VIDEO IN) connector on a monitor . T o assemble a l ...
-
Pelco C2403M-C - page 19
18 C2462M-B (10/05) SPECIFICA TIONS BACKBOX Electrical Input V oltage: 12 VDC or 24 V AC ( ± 10%), auto-sensing Power Consumption: 3 watts or less Video Connector: BNC General Pan/T ilt Adjustment Pan: 360 ° T ilt: 140 ° (20 ° to 160 ° range) Rotation: 360 ° Construction Back Box and Surface Mount Ring: ABS plastic Bubble: Polycarbonate Finis ...
-
Pelco C2403M-C - page 20
C2462M-B (10/05) 19 PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years ...
-
Pelco C2403M-C - page 21
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ® ...
¿Tienes una pregunta acerca de Pelco C2403M-C?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Pelco C2403M-C, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Pelco C2403M-C probablemente compartirá una forma de solucionarlo.