-
Tripp Lite 200502023 - page 1
Owner’ s Man ual Quiet Mobile P o wer Congratulations! Y ou've purchased the most advanced, feature-rich Inverter/Charger designed for recreational applications. T rip p Lite R V Inverter/Chargers are the quiet alternative to generators-with no fumes, fuel or noise to deal with! Y ou get AC electricity any where and anytime you need it: away ...
-
Tripp Lite 200502023 - page 2
Inverter/Charger DC V olt: 12 Wire Gauge T win 00 (2/0) W atts 6 4 2 0 00 (2/0) (RV2012OEM, RV2512OEM & R V3012OEM only) 500 15 ft 25 ft 39 ft 62 ft 79 ft 158 ft. 700 1 1 ft 18 ft 28 ft 44 ft 56 ft 1 12 ft. 1000 N/R 12 ft 20 ft 31 ft 39 ft 78 ft. 2000 N/R N/R N/R 16 ft 20 ft 40 ft. 2400 N/R N/R N/R 13 ft 16 ft 32 ft. 3000 N/R N/R N/R 10 ft 13 f ...
-
Tripp Lite 200502023 - page 3
3R Impor tant Safety Instructions SA VE THESE INSTR UCTIONS! This manual contains important instructions and warnings that should be followed during the installation, operation and storage of all T ripp Lite Inverter/Chargers. Note: For Marine installations, please r eplace this page with the page titled "For Marine Applications Only" fou ...
-
Tripp Lite 200502023 - page 4
4R Feature Identification Identify the premium features on your specific model and quickly locate instructions on how to maximize their use. Configuration DIP Switches: optimize Inverter/Charger operation depending on your application. See Configuration section for setting instructions. Operating Mode Switch: controls Inverter/Charger operation. Th ...
-
Tripp Lite 200502023 - page 5
5R Operation Switch Modes After configuring, mounting and connecting your Inverter/Charger , you are able to operate it by switching between the following oper- ating modes as appropriate to your situation: AUTO/REMOTE: Switch to this mode when you need constant, uninterrupted AC power for connected appliances and equipment. The Inverter/Char ger w ...
-
Tripp Lite 200502023 - page 6
6R Select Battery T ype—REQUIRED (All models) CAUTION: The Battery T ype DIP Switch setting must match the type of batteries you connect, or your batteries may be degraded or damaged over an extended period of time. See “Battery Selection,” p. 10 for mor e information. Battery T ype Switch Position Gel Cell (Sealed) Battery Up W et Cell (V en ...
-
Tripp Lite 200502023 - page 7
7R Select Battery Charger -Limiting Points—OPTIONAL (Not on 612 Models) “Most Limiting” (#B2 & #B1 Up): Charger -limiting takes effect the moment any 120V AC load is applied; charger out- put falls gradually from full output at no 120V load passing through to no output at full load. “Less Limiting” (#B2 Up & #B1 Down, factory sett ...
-
Tripp Lite 200502023 - page 8
8R Set Battery Charging Amps—OPTIONAL (function included on switch on 612 models) Check specifications for your unit’ s high- and low-charging amp options. By setting on high charging, your batteries will char ge at maximum speed and your R V 12V DC system loads will be well-supplied. When setting on low charging, you lengthen the life of your ...
-
Tripp Lite 200502023 - page 9
9R Battery Selection 540 watts ÷ 12V = 45 DC Amps 270 Amp-Hours ÷ 55 Amps In verter/Charger Rating = 5 Hours Rechar ge Select A uxiliary Battery T ype (if any) Select “Deep Cycle” batteries to receive optimum performance from your Inverter/Charger . Do not use ordinary car or starting ba tteries or batteries rated in Cold Cranking Amps (CCA). ...
-
Tripp Lite 200502023 - page 10
10R Mounting W ARNING! Mount y our In verter/Charger BEFORE DC battery and A C power connection. Failure to f ollow these instructions ma y lead to per sonal injury and/or damage to the In ver ter/Charger and connected systems. T ripp Lite manufactures a variety of different Inverter/Char gers with a variety of different mounting options for use in ...
-
Tripp Lite 200502023 - page 11
11R • Connect DC W iring: Though your Inverter/Charger is a high-efficiency con- verter of electricity , its rated output capacity is limited by the length and gauge of the cabling run- ni ng from the bat- tery to the unit. Use the shortest length and largest diameter cabling (maximum 2/0 gauge) to fit your Inverter/Charger’ s DC Input terminal ...
-
Tripp Lite 200502023 - page 12
12R T o avoid overloading your Inverter/Charger , match the power requirements of the equipment you plan to run at any one time (add thei r total watts) with the output wattage capacity of your Inverter/Charger model (see Specifications). Do not confuse “continuous” wattag e with “peak” wattage ratings. Most electric motors require extra po ...
-
Tripp Lite 200502023 - page 13
13R Service Before returning your Inverter/Charger for service, follow these steps: 1.) Review the installation and operation instructions to ensure that the service problem does not originate from a misreading of the instructions. Also, check that the circuit breaker(s) are not t ripped.* 2.) If the problem continues, do not contact or return the ...
-
Tripp Lite 200502023 - page 14
1111 W . 35th Street, Chicago, IL 60609 USA 773.869.1234 (USA) • 773.869.1212 (International) www .tripplite.com 200502023 93-2254_ES ...
¿Tienes una pregunta acerca de Tripp Lite 200502023?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Tripp Lite 200502023, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Tripp Lite 200502023 probablemente compartirá una forma de solucionarlo.