Español dropdown-ico

Manual de instrucciones Extron electronic CS 1226T

33 de páginas 6.42 mb
Descargar

Pasar a la página of 33

Summary
  • Extron electronic CS 1226T - page 1

    User Guide CS 26T and CS 120P Speakers CS 1226T SpeedMount Ceiling Speaker System 6 8-2161-01 Rev . A 08 13 ...

  • Extron electronic CS 1226T - page 2

    Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated danger ous voltage within the product’ s enclosure that may pr esent a risk of electric shock. A TTENTION: This symbol, , when used on the product, is intended to alert the user of important operating and ...

  • Extron electronic CS 1226T - page 3

    FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide r easonable protection against harmful interference when the equipment is operated in a commer cial environment. This equipment generates, uses, and can radiate radi ...

  • Extron electronic CS 1226T - page 4

    Conventions Used in this Guide Notifications The following notifications are used in this guide: W ARNING: A warning indicates a situation that has the potential to result in death or severe injury . A TTENTION: Attention indicates a situation that may damage or destroy the pr oduct or associated equipment. NOTE: A note draws attention to important ...

  • Extron electronic CS 1226T - page 5

    Contents Introduction ............................................................ 1 About this Guide ................................................. 1 Overview ............................................................ 1 Features ............................................................. 1 Application Example ............................... ...

  • Extron electronic CS 1226T - page 6

    CS 26T and CS 120P User Guide • Contents vi ...

  • Extron electronic CS 1226T - page 7

    Intr oduction This section gives an overview of the Extron CS 1226T SpeedMount Ceiling Speaker System, consisting of the CS 26T speakers and CS 120P enclosure. It also pr ovides a list of system features and an application diagram. T opics include: • About this Guide • Overview • Features • Application Example About this Guide T ...

  • Extron electronic CS 1226T - page 8

    • Selectable taps — The rotary tap selector switch, located behind the grille, sets the speaker to operate in either 8-ohm direct or 70 volt /100 volt operation with 16, 8, 4, 2, and 1 watt taps. • Magnetic grille — Magnets spaced around the grille edge enable it to be easily attached and to remain firmly in place. Application Example ...

  • Extron electronic CS 1226T - page 9

    Installation This section provides instructions for installing the CS 26T speakers and the CS 120P enclosure. T opics include: • Installation Considerations • Installation Configurations • Installing the CS 1226T — Single Installer • Installing the CS 120P in a Suspended Ceiling — Division of Labor • Installing the CS 2 ...

  • Extron electronic CS 1226T - page 10

    Installing the CS 1226T System — Single Installer If a single installer is installing the CS 1226T system, follow this procedur e for the entire system: NOTE: The ceiling grid must be installed before the installation of the CS 1226T begins. • V erify if fiberglass ceiling tiles ar e being used (see step 2 below and step11 on page 7 for ...

  • Extron electronic CS 1226T - page 11

    e. Cut out the circle traced in the ceiling tile. f. Replace the tile in the ceiling. 4. R emove the adjacent ceiling tile — T o facilitate the installation process, r emove the tile adjacent to the ceiling tile where the CS 26T will be installed. If the CS 120P is being installed, skip to step 6. Otherwise, proceed to step 5. 5. If NOT using the ...

  • Extron electronic CS 1226T - page 12

    8. Route the cables through the cover plate — NOTES: • The CS 120P is fully UL 2043 compliant only when it is used with a metal conduit or with plenum rated cables. • Installation of all conduits, conduit adapters, wiring, and electrical connections must conform to all applicable building codes and local ordinances. Using a flexible conduit: ...

  • Extron electronic CS 1226T - page 13

    9. Wire the CS 120P — Route the wir es through the H-shaped opening in the CS 120P . Be sure to leave suf ficient slack. Figure 8. Route the Wires Thr ough the H-shaped Opening 10. Replace the terminal cover plate — Reinstall the terminal cover plate onto the CS 120P and tighten the two screws that wer e previously loosened. 11. If the CS 120P ...

  • Extron electronic CS 1226T - page 14

    12. Place the CS 120P into the ceiling grid — Place the CS 120P over the tile grid so that the CS 120P is safely supported on the two short edges. Ensure that the hole in the tile is aligned with the hole in the CS 120P (see figure 10). Fig: Mounting the PRE NOTE: 2' x 2' (600 mm x 600 mm) grid mounting is the same as 2' x 4' ...

  • Extron electronic CS 1226T - page 15

    16. Attach the speaker wires to the captive screw connector — A TTENTION: Do not tin the wires. Tinned wires do not r emain tight in the captive screws and can br eak easily after several bends. Number of Wires per Connection Point Maximum Wire Gauge 1 12 AWG 2 16 AWG 4 18 AWG Attach the speaker wires to the included four -pole captive screw conn ...

  • Extron electronic CS 1226T - page 16

    • Wiring Multiple Speakers Using Loop-through: A loop-through electrical connection is made on the cr ossover board of the CS 26T . Connect the wires to the captive scr ew connectors of the speakers, as shown in figure 15. Be sur e to tighten the screws. Speaker 1 Speaker 2 Wiring Multiple Speakers Using Loop-through IN – LOOP – IN + LOOP ...

  • Extron electronic CS 1226T - page 17

    • The impedance of the speakers downstream of the one being tested can be measured while the system is on by connecting to the outer (LOOP) terminals of the captive screw connector , as shown in figure 17. Impedance T est Points To next speaker(s) Red Wire (+) fr om Amplifier Black Wire (-) fr om Amplifier Amplifier Te st Points Figure 17. ...

  • Extron electronic CS 1226T - page 18

    18. Attach the speaker wire to the strain relief tie down point using the pr ovided zip tie. Captive Sc re w Connector Strain Relief Ta b (zip tie) Figure 19. Attaching the Speaker Wir e to the Strain Relief Point 19. Mount the CS 26T (see figure 20). a. Insert the CS 26T through the bottom of the hole in the ceiling tile that was cut in step 3. b. ...

  • Extron electronic CS 1226T - page 19

    20. Attach secondary support lines — If requir ed, attach all of the secondary support lines as shown in figure 21. A TTENTION: Do not allow any slack in the support cables. NOTE: If the CS 26T will be installed in the CS 120P , do not attach secondary support cables to the speakers. Secondary Support Cables (3) Attach cables he re and secure. An ...

  • Extron electronic CS 1226T - page 20

    22. Set the rotary tap selector switch — Use a small screwdriver to set the tap selector switch to the appropriate setting. A TTENTION: When setting the taps for a distributed (high impedance) system, do not tap the system above the rated power of the amplifier . When connecting multiple speakers in 8-ohm mode, be sure that the combined rated im ...

  • Extron electronic CS 1226T - page 21

    Installing the CS 120P in a Suspended Ceiling — Division of Labor In a division of labor installation, low-voltage contractors install the CS 120P enclosure (construction rough-in phase). NOTE: The ceiling grid must be installed before the installation of the CS 1226T can begin. • V erify if fiberglass ceiling tiles ar e being used (see ste ...

  • Extron electronic CS 1226T - page 22

    4. Cut a hole for the CS 26T speaker . Use the provided cutout template to outline the hole to be cut in the ceiling tile as described below . (If the ceiling tile will not be installed during this phase of the installation, skip to step 6 .) a. Remove the ceiling tile. b. T o find the center of the tile, use a tape measure to measure the space bet ...

  • Extron electronic CS 1226T - page 23

    7. Route the cables through the cover plate — NOTES: • The CS 120P is fully UL 2043 compliant only when it is used with a metal conduit or with plenum rated cables. • Installation of all conduits, conduit adapters, wiring, and electrical connections must conform to all applicable building codes and local ordinances. Using a flexible conduit: ...

  • Extron electronic CS 1226T - page 24

    8. Wire the CS 120P — Route the wires through the H-shaped opening in the CS 120P . Be sure to leave suf ficient slack. Figure 29. Route the Wir es Through the H-shaped Opening 9. Replace the terminal cover plate — Reinstall the terminal cover plate onto the CS 120P and tighten the two screws that wer e previously loosened. 10. If the CS 120P i ...

  • Extron electronic CS 1226T - page 25

    11. Place the CS 120P into the ceiling grid — Place the CS 120P over the tile grid so that the CS 120P is safely supported on the two short edges. If the ceiling tile was installed, ensure that the hole in the tile is aligned with the hole in the CS 120P (see figure 31). Fig: Mounting the PRE NOTE: 2' x 2' (600 mm x 600 mm) grid mountin ...

  • Extron electronic CS 1226T - page 26

    Installing the CS 26T in a Suspended Ceiling — Division of Labor In a division of labor installation, an A V system contractor installs the CS 26T (final installation phase). Use the following procedur e: NOTE: Observe all applicable building codes and local ordinances when installing the speaker . 1. Disconnect power — Power down all attached ...

  • Extron electronic CS 1226T - page 27

    5. Attach the speaker wires to the captive screw connector — A TTENTION: Do not tin the wires. Tinned wires do not r emain tight in the captive screws and can br eak easily after several bends. Number of Wires per Connection Point Maximum Wire Gauge 1 12 AWG 2 16 AWG 4 18 AWG Attach the speaker wires to the included four -pole captive screw conne ...

  • Extron electronic CS 1226T - page 28

    • Wiring Multiple Speakers Using Loop-through: A loop-through electrical connection is made on the cr ossover board of the CS 26T . Connect the wires to the captive scr ew connectors of the speakers, as shown in figure 36. Be sur e to tighten the screws. Speaker 1 Speaker 2 Wiring Multiple Speakers Using Loop-through IN – LOOP – IN + LOOP ...

  • Extron electronic CS 1226T - page 29

    • The impedance of the speakers downstream of the one being tested can be measured while the system is on by connecting to the outer (LOOP) terminals of the captive screw connector , as shown in figure 38. Impedance T est Points To next speaker(s) Red Wire (+) fr om Amplifier Black Wire (-) fr om Amplifier Amplifier Te st Points Figure 38. ...

  • Extron electronic CS 1226T - page 30

    7. Attach the speaker wire to the strain relief tie down point using the pr ovided zip tie. Captive Sc re w Connector Strain Relief Ta b (zip tie) Figure 40. Attaching the Speaker Wir e to the Strain Relief Point 8. Mount the CS 26T (see figure 41). a. Insert the CS 26T through the bottom of the hole in the ceiling tile that was cut in step 2. b. T ...

  • Extron electronic CS 1226T - page 31

    9. Set the rotary tap selector switch — Use a small screwdriver to set the tap selector switch to the appropriate setting. A TTENTION: When setting the taps for a distributed (high impedance) system, do not tap the system above the rated power of the amplifier . When connecting multiple speakers in 8-ohm mode, be sure that the combined rated imp ...

  • Extron electronic CS 1226T - page 32

    Installing the CS 120P in a Har d Ceiling If you are installing the CS 1226T in a har d ceiling (having no ceiling tiles), with the ceiling structure in place, install the CS 120P: • It is the responsibility of the installer to identify a suitable mounting location and pr ovide the mounting hardwar e. • The CS 120P must be mounted as clos ...

  • Extron electronic CS 1226T - page 33

    © 2013 Extron Electr onics All rights reserved. www .extron.com Contact Information Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - W est Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 F AX +1.919.850.1001 F AX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 F AX Extron ...

Fabricante Extron electronic Categoría Speaker

Los documentos del dispositivo Extron electronic CS 1226T que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Extron electronic
- manuales de instrucciones CS 1226T
- hojas de producto Extron electronic
- folletos informativos
- o etiquetas energéticas Extron electronic CS 1226T
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Extron electronic CS 1226T.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Extron electronic CS 1226T, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Extron electronic CS 1226T. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Extron electronic CS 1226T.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Extron electronic CS 1226T, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Extron electronic CS 1226T. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Extron electronic CS 1226T.

El manual de instrucciones completo de Extron electronic debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Extron electronic CS 1226T - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Extron electronic CS 1226T, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Extron electronic CS 1226T que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Extron electronic CS 1226T - que deben facilitarnos los primeros pasos durante el uso de Extron electronic CS 1226T
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Extron electronic CS 1226T
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Extron electronic CS 1226T en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Extron electronic CS 1226T?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Extron electronic CS 1226T, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Extron electronic CS 1226T probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)