-
Culligan Sulfur-Cleer - page 1
Culligan ® Sulfur-Cleer ™ Automatic Water Filter Owners Guide ...
-
Culligan Sulfur-Cleer - page 2
Thank You And Welcome To Your New World Of Better Living With Culligan Water. This system and its installation must comply with state and local regulations. The System is ONLY to be supplied with cold water. The Culligan ® Sulfur-Cleer ™ water filters have been tested against WQA S-200 for the effective reduction of iron up to 1,000 gallons and ...
-
Culligan Sulfur-Cleer - page 3
Table of Contents iii S p e c i fi c a t i o n s ................................................1 I n t r o d u c t i o n ..................................................2 O p e r a t i n g C o n d i t i o n s ...........................................4 F a m i l i a r i z a t i o n ................................................5 P r o g r a ...
-
Culligan Sulfur-Cleer - page 4
This page intentionally left blank. iv ...
-
Culligan Sulfur-Cleer - page 5
Specifications Culligan ® 10” Sulfur-Cleer ™ Filter with Fiberglass Tank Control Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1” 5-cycle reinforced thermoplastic T i m e r ................................................... E l e c t r o n i c C i r c u i t B o a r d O v e r a l l C o n d i t i o n e r H e ...
-
Culligan Sulfur-Cleer - page 6
Introduction Operation Step 1. Service Cycle In the service cycle, raw water enters the inlet port of the media tank. The oxidation process begins. This air/water contact oxidizes the iron and hydrogen sulfide in the water. Oxidized iron particles are trapped by the filter bed as the water passes through. Filtered water enters the lower distribut ...
-
Culligan Sulfur-Cleer - page 7
Step 3. Filter Tank Operation - Backwash Cycle Reversing the flow of water through the filter bed and backwashing dirty water to the drain cleans the filter bed. Raw water enters the filter control valve through the inlet port and is directed down the distributor tube and out the lower distributor at the bottom of the tank, flowing upward thro ...
-
Culligan Sulfur-Cleer - page 8
The concentration limits listed below reflect the minimum or maximum individual limit that each contaminant was tested for separately without any interference of other contaminants in the influent water. In reality, however, we know that these contaminants may be present in combination which may limit the filter’s ability to remove these conta ...
-
Culligan Sulfur-Cleer - page 9
Fam ilia riz atio n Power Loss The Circuit b oard is equipped with a Hi-Cap Capacitor and EEPROM memory chip. The capacitor is capable of maintaining the time, for at least two days, in the event of a power outage. The EEPROM ensures that the individual programming parameters of your filter are not lost. If the power outage lasts long enough to dr ...
-
Culligan Sulfur-Cleer - page 10
Modes of Operation Manual Regeneration Pressing and holding the regen button for 5 seconds will initiate an immediate regeneration. The beeper is to give one beep at the start of manual regeneration (when the motor starts to turn). In delay mode, pressing and releasing the regen button will light the regen icon for regeneration to occur at the set ...
-
Culligan Sulfur-Cleer - page 11
7 The circuit board controls all of the filter functions. These settings are programmed at the time of installation. The following is a list of all the microprocessor functions, in the event that any of the settings need to be adjusted. Display Icons The display is to be backlit and have the icons as shown. Custom LCD Display Six standard 12-segme ...
-
Culligan Sulfur-Cleer - page 12
8 • Time of Regeneration - This setting is used to program the time at which a regeneration is to occur in the delay mode. The display will first show “tor” for two seconds. After “tor” is shown the display will then show the default of 2:00 AM (or the current programmed time of regeneration if already set). The time can be adjusted in 3 ...
-
Culligan Sulfur-Cleer - page 13
9 If any of the days were set to “yes”, the display will show “SETDAY” followed by “SUN”. This selects the current day of the week. The “+” or “-“ key toggles through the days of the week and pressing the “STATUS” key saves the setting and advances to the next programming step. If ALL of the days were set to “no”, then ? ...
-
Culligan Sulfur-Cleer - page 14
Programming (cont.) • Filter Media Life - This setting is available only with flow meter attached. It enables or disables an alert code ( CHANGE MEDIA ) that indicates the end of life for the filter media. The display will show “LIFE” in the left most characters and toggle between “Y” and “N” in the right most character with the “ ...
-
Culligan Sulfur-Cleer - page 15
Programming (cont.) • Auxiliary Output #1 “ON” Time - This setting is used to control the “ON” time of the aux1 output which turns on the compressor and vent solenoid. The aux 1 output should act independently, however, it should never be activated during a regeneration. Upon power up or immediately after a regen, the “ON” time should ...
-
Culligan Sulfur-Cleer - page 16
12 The statistical functions are reached by pressing the “Information” key. Repetitive presses of the “Statistics” key will cycle through the standard statistics mode until cycled back to time of day display. Once either of the Information menus is entered the information shown for each display is outlined below: • Flow Rate (Meter mode o ...
-
Culligan Sulfur-Cleer - page 17
When and How to Bypass Your Water Conditioner 13 Normally, all water except outside lines passes through the water conditioner. There are times when the water conditioner should be bypassed, using the push-button Cul-Flo-Valv ® Bypass, or a 3-way bypass valve. You should bypass: 1. If lines to outside faucets do not bypass the water conditioner, a ...
-
Culligan Sulfur-Cleer - page 18
Regeneration with Bleach When bleach is used to regenerate the Sulfur-Cleer ™ , Culligan strongly recommends the dealer set-up a service contract with the customer to initiate the regeneration when required. If a service contract is not practical, then Culligan recommends the dealer and the customer strictly abide by the following procedure when ...
-
Culligan Sulfur-Cleer - page 19
15 Things to Check Before You Call for Service If you unexpectedly experience problem water, make these simple checks before calling your Culligan dealer. One of the following conditions may be the reason for your interruption of service. Important If any of the following conditions is found, the water filter should be manually recharged according ...
-
Culligan Sulfur-Cleer - page 20
16 Preventative Maintenance The Culligan Sulfur-Cleer ™ water filter has been designed to provide a good, consistent service life. Because of the nature of problem water, we recommend that the local Culligan dealer provide regular maintenance/service contracts for the proper operation of your systems. The water filter service begins with a mult ...
-
Culligan Sulfur-Cleer - page 21
17 Troubleshooting Guide Complaint Problem Cause Solution Iron bleed- through or staining. A. Inadequate backwash of filter 1. Plugged drain line flow control 1. Call your Culligan dealer for service. 2. Insufficient water supply from well. 2. Check for minimum specified flow and pressure requirements of filter system. 3. Plugged media tank i ...
-
Culligan Sulfur-Cleer - page 22
Troubleshooting Guide (cont.) 18 Complaint Problem Cause Solution Water leaking from relief valve. A. Dirt lodged under seat of valve. 1. Pressure has exceeded rating on relief valve and caused valve to open 1. Call your Culligan dealer for service. B. Faulty or defective relief valve 1. Call your Culligan dealer for service. Water is effervescent ...
-
Culligan Sulfur-Cleer - page 23
19 Troubleshooting Guide (cont.) Complaint Problem Cause Solution Water is running to drain continuously. A. Control valve is stuck in regeneration cycle. 1. Electrical service to control(s) has been interrupted. 1. Assure continuous electrical service is available. (check plug, breaker, fuse, etc.) 2. Faulty circuit board. 2. Replace circuit board ...
-
Culligan Sulfur-Cleer - page 24
20 Performance Data Sheet Culligan ® Sulfur-Cleer ™ Water Filter Important Notice — Read this data sheet and compare the capabilities of the unit to your actual water treatment needs. Culligan recommends that you have your water supply tested to determine these needs before purchasing a water treatment unit. Culligan knows the more informed yo ...
-
Culligan Sulfur-Cleer - page 25
21 Records and Data Important Data on Your Water Filter It is advisable to have the salesperson or installer fill in the information below for your future reference. If this has not been done, please ask for it, as it is necessary if you contact your dealer. Identification Model Name Catalog No. Control Model No. Control Serial No. Date of Install ...
-
Culligan Sulfur-Cleer - page 26
Culligan Limited Warranty 22 Culligan ® Sulfur-Cleer ™ Automatic Water Filters You have just purchased one of the finest water conditioners made. As an expression of our confidence in Culligan International Company products, your water conditioner is warranted to the original end-user, when installed in accordance with Culligan specifications ...
-
Culligan Sulfur-Cleer - page 27
23 You Get Your Water Expert, The Culligan Man ® We’re here to provide you with fast, dependable service, making sure any problems you have are taken care of. The Culligan Man has been around for over seventy years, delivering dependable service all along. That’s why people say “Hey, Culligan Man!” ® Because we’re the water experts. And ...
¿Tienes una pregunta acerca de Culligan Sulfur-Cleer?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Culligan Sulfur-Cleer, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Culligan Sulfur-Cleer probablemente compartirá una forma de solucionarlo.